A wall hung toilet looks simple once it is on the wall. The work behind it is not. Before the bowl of the Wall Hung Toilet 1051W is fixed in place, the rough-in, the supporting frame, the concealed cistern, the access route for future servicing and the finished wall build-up all have to be settled on paper. A plan that covers these items keeps the plumbing trade, the tiling trade and the joiner working from the same drawing instead of arguing on site.

This article sets out what a complete installation plan for the 1051W should contain, in the order the decisions actually have to be made.

Start with the bowl dimensions and the waste outlet

The published envelope of model 1051W is 530 mm deep by 360 mm wide by 360 mm high, and it discharges through a P-trap with a 180 mm rough-in. Those two figures drive everything else on the drawing.

Write both onto the plan before anything else:

  • the height of the waste centre above the finished floor, which sets where the horizontal drain enters the wall;
  • the depth of the bowl projection from the finished wall face, which decides how much clear floor space is left in front of it;
  • the height of the rim above the finished floor, agreed with the client before the frame is fixed.

The 180 mm P-trap figure is a nominal value from the product page. Mark it on the drawing as a reference dimension and confirm it against the current technical data sheet for the batch being ordered, then send that confirmed number to the site team. A rough-in treated as approximate is the single most common cause of a bowl sitting proud of the wall or a waste connection being rebuilt.

Specify the supporting frame and how it reaches the structure

A wall hung bowl carries live load, so the plan has to state where that load goes. Show the frame position, the fixing points, and whether the load is taken by timber or steel studs, by a masonry wall, or by a framed enclosure built out from the wall. Note the stud centres and the need for solid blocking behind every fixing point.

On a stud wall that cannot take the load directly, a floor-supported enclosure is usually the practical answer. The plan should then show the enclosure dimensions, the position of the access panel, and how the finished face relates to the tile line, because the bowl bolts to the frame and not to the tile.

Show the concealed cistern and the flush plate

The 1051W is designed to work with a concealed water tank system. The plan needs one drawing that fixes three items together:

  • the cistern position inside the wall or enclosure, including its depth and the fill connection;
  • the flush plate position on the finished face, set high enough on the panel to be used comfortably and clear of the shower screen, mirror and towel rail;
  • the air gap and fixing detail between the flush plate and the bowl.

Draw the flush plate on the tiled elevation, not only on the plumbing riser. When it is drawn twice in two different trades' documents, it ends up in two different places.

Keep a service access route open

Everything except the bowl is behind a wall once the tiles are on. The plan must show how a plumber reaches the fill valve, the flush mechanism and the waste connection later, without breaking the finish. Two details are worth drawing explicitly: the access panel through the enclosure, sized so that a hand and a tool fit inside it; and the bowl-to-frame connection, which should be removable with standard tools.

If the design calls for an access panel hidden behind a mirror or cabinet, note that on the plan and give the opening dimensions. An access route that exists only as an idea is not an access route.

Record the wall build-up and the finished floor line

Wall hung ware is set out from finished faces, so the plan has to state the make-up of both. List the wall as a build-up: frame, cistern, batten, lining, waterproofing where wet, adhesive, tile. Give the total thickness and show it against the room dimension. Do the same for the floor, including screed or adhesive bed and the floor finish.

This is also where the wall-hung benefit is realised. Because the 1051W leaves the floor empty, the tile can run continuously under it and the floor can be mopped in one pass. That only works if the floor tiles are set out before the bowl position is fixed, so show the tile line on the same drawing as the bowl centre.

Check the ceramic and the glaze against the use

The 1051W is made from vitreous ceramic with a glossy glaze, which resists limescale and staining and takes routine cleaning well. For a hotel or serviced apartment bathroom, add to the plan who cleans the bowl daily and with what, since aggressive acidic cleaners damage glaze and metal trim over time. A short care note issued with the handover pack saves disputes later.

For projects specifying more than one fixture from the same range, note that the 1051 series also covers matching Wall Hung Ceramic Basin 1051B, Freestanding Pedestal Basin 1051S and the one-piece Washdown One Piece Toilet 1051A. Grouping them on one schedule keeps the look of a guest bathroom or a run of hotel rooms consistent, and it puts all the sanitary ware on a single order.

Plan the rest of the wet room around it

The bowl sits inside a larger fit-out. The installation plan should carry the coordinating items rather than leave them to be picked up on site:

  • the vanity or countertop and its basin, drawn at the same scale as the toilet so clearances between fixtures can be read off the drawing;
  • the shower set and its controls, checked against the position of the bowl and the enclosure;
  • mirror cabinet, lighting and towel rail positions on the tiled elevations;
  • wall panelling or stone finishes where they meet the tiled enclosure.

Where a project needs these items together, SANTERSON supplies bathroom ceramics, vanities, showers, lighting and interior fixtures as part of one furniture and building materials programme, which shortens the coordination list on a villa or hospitality job.

Finish the plan with a pre-fix sign-off list

Before any wall is closed, the plan should be signed off against a short list:

  1. confirmed rough-in and waste height from the current data sheet;
  2. frame fixing points blocked into the structure;
  3. cistern fill and flush plate positions marked on the finished elevations;
  4. access panel size and location shown;
  5. wall and floor build-up thicknesses stated;
  6. bowl rim height agreed with the client;
  7. care and cleaning note prepared for handover.

A wall hung toilet is judged by how clean the finished wall looks. It is installed correctly by what the drawing settled beforehand. Put the rough-in, the frame, the cistern, the access route and the build-up on one set of coordinated drawings, and the 1051W goes up in a day.