A sheet of MCM flexible travertine stone veneer arrives on site looking like a roll of stone rather than a crate of slabs. That single difference changes the whole delivery and installation plan: fewer crates, lighter loads, no lifting gear for curved surfaces, and a cutting trade instead of a stonemason. This article walks through how buyers, contractors and project managers line up sampling, substrate preparation, quantities, freight and fixing sequence for this bendable soft stone, so the cladding goes on the wall without re-orders, re-cuts or waiting on trades.

Why flexible stone behaves differently from rigid cladding

SANTERSON describes MCM flexible travertine as an ultra-thin, lightweight and bendable modified-clay sheet that replicates the natural hole texture of travertine. Because it is thin and flexible, it wraps curved walls, cylinders and special-shaped surfaces that rigid stone panels cannot follow without expensive kerfing or heat forming. The practical consequence for scheduling is that the wall shape stops being a fabrication problem and becomes a fixing detail.

The same flexibility changes what has to be checked before the sheets are ordered. A rigid panel schedule assumes flat planes, right angles and factory-cut edges. Flexible stone is cut on site with simple tools, so most adjustments happen at the wall rather than in the factory. That shortens lead time but shifts responsibility onto accurate setting-out and a properly prepared base.

Step 1: Confirm the substrate before you confirm the order

Flexible stone sheets are bonded to the base with tile adhesive, so the base decides whether the installation holds. Before quantities are signed off, get written confirmation from the site team on:

  • Base material. Cement-based render, blockwork or gypsum board are the bases this product family is fixed to; timber framing, steel and existing tile each need their own preparation note.
  • Flatness and soundness. A thin sheet follows the surface rather than bridging it, so hollow render, cracks and uneven plaster will read through the finished face.
  • Curvature radius. Record the actual radii of arches, columns and feature curves on drawing, because tight radii change how sheets are cut and overlapped at joints.
  • Interior or exterior exposure. Facade, parapet and exposed walls need a fixing and jointing approach suited to weather; interior feature walls do not.

Ask for this information in the same round as the design query. If it arrives after production starts, the re-specification costs more than the time it saved.

Step 2: Order samples and settle the colour run early

Travertine-look flexible stone is produced in multiple colours, and SANTERSON supplies free samples so buyers can judge texture and tone against the actual lighting of the project. Order samples for every colour under consideration, not just the preferred one, and pin them to a wall on site for a few days. Interior LED lighting and daylight shift the apparent warmth of beige and cream tones far more than a catalogue image suggests.

Settle three points while the samples are circulating:

  • The colour or colours to be used, including whether feature walls intentionally mix tones.
  • The batch plan — whether all wall areas draw from one production run or from staged runs per zone.
  • Who signs off the approved sample, and how it is stored on site as the reference for inspection.

Step 3: Take off quantities with waste and spare stock built in

Flexible sheets are cut on site, so take-off should follow the setting-out drawing rather than a nominal panel count. Work through the wall areas in the order the trades will install them.

Area typeWhat to measurePlanning note
Flat interior wallsNet face area, less openings; add a cutting allowance for the sheet formatStraight runs are the fastest work on site — schedule them first so the fixing crew establishes adhesive open time and joint rhythm.
Curved walls, arches, columnsDeveloped surface area plus overlap at each wrap and returnCut patterns for tight radii during the mock-up, not during production. Log the radius of every curve on the drawing.
External facade and feature entrancesNet area plus detailing at edges, reveals and terminationsFix these zones after the interior run so the crew is practiced before weather-exposed work begins.
Renovation over existing finishesExisting surface condition, plus removal or overboarding allowanceOld render and loose tile are the most common cause of delay on refurbishment walls; survey them before delivery, not after.

Order spare material with the main consignment. Off-cuts cover future repairs and any panel that gets damaged after handover, and a later top-up order may come from a different production run.

Step 4: Group the flexible stone with the rest of the fit-out in one shipment

Wall cladding rarely arrives alone. A hospitality or villa package normally includes cabinetry, doors, vanities, lighting and loose furniture, and each of those has its own production clock. As a one-stop furniture and building materials supplier, SANTERSON handles freight forwarding by sea, air and rail along with customs paperwork, packing lists, certificates of origin, container loading and shipment tracking, so cladding can be consolidated with joinery instead of travelling as a separate small consignment.

Two sequencing rules keep that consolidation useful:

  • Cladding lands before the wet trades finish. Adhesive-bonded sheets need a dry, cured base. Book the delivery date against the render and plaster completion date, not against the general fit-out start.
  • Heavy or bulky joinery lands after the cladding on shared corridors. Cabinetry and stone-look panels travelling through the same doorway should arrive in the order they are installed, so finished walls are not damaged by later deliveries.
Confirm import terms, duties, insurance and delivery scope for each project individually. Freight arrangements are quoted per consignment and destination; nothing in a product article guarantees transit time or landed cost.

Step 5: Build the installation sequence into the programme

For most projects the fixings follow a fixed order, and the programme should show it explicitly:

  1. Setting-out. Mark curves, reveals and joint lines on the prepared base; confirm heights of switch plates, sockets and service outlets against the sheet layout.
  2. Mock-up panel. Fix one flat section and one curved section for approval before opening the full batch. This is where colour match, joint width and adhesive coverage get signed off.
  3. Flat runs. Complete straightforward walls first to lock in the work rhythm and adhesive timing.
  4. Curved and special-shaped surfaces. Wrap arches, columns and feature curves once the crew is familiar with the sheet's behaviour.
  5. Joints and terminations. Treat edges, internal corners and reveals last, when any cut adjustments are already resolved.
  6. Snag list and protection. Walk the walls with the client representative, protect finished surfaces from later trades, and record the approved sample reference for future repairs.

Handover records that make repairs simple

At completion, keep four items in the project file: the approved physical sample, the colour and batch reference from the packing list, the setting-out drawing showing curve radii, and the spare stock location. Flexible stone is repaired panel by panel, so a future maintenance crew that has these four items can match a replacement without re-cladding a whole wall.

Related flexible cladding options from the same range

Projects that mix textures often specify more than one bendable sheet. The MCM flexible rammed earth panel reproduces the rough layered look of traditional rammed earth in white and earth-brown tones, fixed to cement bases or gypsum board with tile adhesive and cut on site with simple tools — a common pairing for homestay, restaurant and villa lobbies where travertine is used in the wet and public areas. The flexible wood grain cement wall panel takes the same flexible format in a mineral, cement-based sheet with a moulded timber surface; it is described as non-combustible and water-resistant, can be rolled for transport, and has a white raw surface that can be painted to a project colour.

Specifying all three families on one purchase order means one set of samples, one freight consignment and one installation crew cycle, which is where the coordination effort pays back most.

Start with a drawing and a wall list

Send the setting-out drawing, the interior and exterior wall schedule, and the curve radii, and SANTERSON's team can advise sheet format, colour run and packing plan for your project. Enquiries through the contact page are answered within 24 hours during business hours (Monday to Saturday, 8:00 AM to 6:00 PM GMT+8). Ask for free samples with your first enquiry so colour approval runs in parallel with the quantity take-off.

Product specification, fixing method and jointing details should always be confirmed against the current product page and the project's local building requirements before ordering. The MCM flexible travertine stone veneer product page lists the available colours, applications and the installation approach summarised above.