A quotation for an outdoor swim spa usually arrives as a short PDF with a model number, a set of dimensions and a price. Two suppliers can quote the same WS-S04B shell at very different totals, and the difference is almost never visible on the first read. The buyer who signs the cheaper sheet often pays the gap later, in electrical work, in freight surcharges or in equipment they assumed was included.

This guide walks through how to read a manufacturer’s proposal for the Outdoor Swim Spa WS-S04B line by line: what each specification actually controls on site, which lines must be confirmed in writing before an order is placed, and what a complete submission should contain. It is written for procurement staff, contractors and project managers specifying a spa for a villa, resort or private residence.

The short version: treat the model number as a starting point, not a specification. The lines that decide your site cost are the equipment list, the electrical load, the filtration arrangement and what the freight quote excludes. Ask every supplier for those four items in writing, then compare like with like.

1. Confirm the model code matches the configuration you were shown

The catalogue holds dozens of swim spa listings under a handful of prefixes — WS-S, WS-PC, WS-SP and the numbered 115/125/130 series. Letters appended to a code are not decoration: within one family you will find base codes alongside variants carrying B, X, T, U, M, C, CT, L and S suffixes, plus separate listings for each. The WS-S04, WS-S04B and WS-S04X are three distinct listings, each with its own detail page.

The practical consequence: a supplier may quote you on the base model after you have toured a showroom example or reviewed photographs of a different variant. Check that the exact code in the quotation header matches the model whose specifications you were evaluating, and that the product image attached to the quotation is the same unit. If a proposal quotes “WS-S04 series” without a full code, send it back.

2. Read the shell dimensions against your site, not against the brochure

The published catalogue dimension for WS-S04B is 3900 × 2200 × 1450 mm. Those three numbers are where most early planning errors begin, because a spa is never installed at its shell size.

Work outward from the shell in three stages:

  • Structural opening. The 3900 mm length and 2200 mm width must fit the prepared plinth or recess with tolerance for levelling. Confirm whether the quoted dimension is the outer shell or includes any perimeter cladding, steps or an integrated bench.
  • Access route. The unit travels to site as a fabricated shell, not as loose components. Measure gates, doorways, turning radii and any overhead obstruction along the delivery path, and confirm with the supplier how the spa is craned or carried into position. A 1450 mm height matters less than the smallest pinch point on your route.
  • Plant and service space. Pumps, the filter pump and the control system need a reachable location and clearance for maintenance. Anything you intend to bury behind finished walling should be excluded from the enclosure or given an access hatch.

Ask the manufacturer to state which dimension is shell, which is footprint and whether steps are part of the quoted item. If your architect has drawn a recess, send them the drawing and ask for written confirmation that the proposed configuration fits it.

3. Turn the equipment list into a line-by-line inclusion table

The published specification sheet for WS-S04B records the following. Use it as your comparison baseline and require every supplier to confirm each row against their own quotation:

Specification line Catalogue entry for WS-S04B What to verify in the proposal
Control system 1 set Which controller, where it mounts, whether remote or app control is included or optional.
Water pump 3 pcs Output per pump and which jets each drives. Pump count alone does not tell you the pressure at any seat.
Filter pump 1 pc Flow rate, filter type and whether sand filtration is included or an option.
Jet total 31 pcs; 6 water columns Layout drawing showing jet positions, and whether all jets run simultaneously or in zones.
LED lighting 2 pcs; 28 small LED lights Which fittings are body lights and which are accent lighting, plus control method.
Total power 10.35 kW Whether this figure includes the heat pump, and the supply it assumes.
Swim training system Not listed Explicitly ask whether a swim current is offered for this model and at what cost.
Features shown Water jets, LED lighting, Ozone Whether ozone generation and any sterilisation are fitted or optional extras.

Two of those rows deserve particular attention. The catalogue records the swim training system as not listed for WS-S04B, so if a swim current is central to how you intend to use the spa, do not assume it exists on this model — ask, and let the answer decide whether you should be looking at a longer model instead. And note that the catalogue also flags configuration-dependent availability across the range: options such as control systems, UV sterilisation, additional water pumps, heat pumps, sand filtration, insulation and steps are listed as catalog options whose compatibility varies by model. A low quote is frequently a base configuration with those items removed.

Do not hard-code a figure from the catalogue into your own tender documents. Published specification sheets are transcriptions of product pages, and pages get revised. Require the supplier to restate every number in the quotation itself, dated, and to sign the version they are pricing against.

4. Reconcile the electrical load before you accept a price

A total power figure of 10.35 kW is a substantial load, and it is the line most likely to be misread. Three questions decide whether your quotation is comparable with another supplier’s:

  • What is inside the 10.35 kW? Heating is normally the dominant draw. If one proposal includes a heat pump and another lists it as an option, their power figures and their prices are not measuring the same machine.
  • What supply does the manufacturer assume? Single-phase or three-phase, voltage and frequency vary by market. Ask for the required supply in writing and give that requirement to your electrician early; upgrading a service late in a project is expensive work.
  • Where does the spa’s wiring end? Establish the boundary between factory-supplied components, local electrical work and any control or protection devices you must source locally. Get that demarcation stated in the proposal.

The catalogue entry for this model carries an explicit instruction to confirm included equipment and electrical requirements for the selected configuration. Treat that as a requirement, not boilerplate: the manufacturer’s own documentation is telling you that the published numbers describe a range, not your unit.

5. Check what the freight quotation leaves out

A swim spa is heavy, awkward and priced as an installed asset, so the delivery terms change the real cost more than with most goods on a project list. A supplier working across furniture and building materials will typically arrange sea, air or rail freight, handle customs paperwork and packaging, and quote door to door — but the boundary of that service is what you need in writing.

For each proposal, confirm:

  • the Incoterm and exactly which leg of the journey the price covers;
  • whether unloading at site, crane hire and carry-in are included or your responsibility;
  • who prepares import documentation and who pays duty and clearance;
  • whether cargo insurance is in the quoted price or offered separately;
  • the packaging type and container arrangement, which determines whether a second unit on the same project can share a container.

If you are also sourcing poolside loungers, pergolas, outdoor dining sets or wet-area finishes from the same vendor, ask for a combined shipment. Coordinating swim spa, outdoor furniture and interior fixtures through one supplier reduces the number of separate consignments, delivery windows and site handovers to manage.

6. Test the vendor’s after-sale position in writing

Marketing pages promise installation support, snag inspection, warranty cover, spare parts and maintenance response times. Those promises are worth nothing until they appear in your contract with defined scope. Before you sign, ask three specific questions:

  • Who performs commissioning on site? A manufacturer’s own team, a local subcontractor or your contractor. Ask which, and what training is handed over.
  • What exactly does the warranty cover, and for how long? Shell, pumps, jets, controls, lighting and heating usually carry different terms. Ask for them itemised.
  • How are spare parts supplied after year one? A pump or controller that cannot be replaced locally turns a serviceable product into an unusable one.

Any response time quoted in marketing material should be treated as a claim to verify, not a service level. Put the number you need in your purchase order and see whether the supplier accepts it.

7. Score the proposal itself

The quality of a submission tells you a great deal about how the project will run. A manufacturer comfortable with export projects will send a complete pack without being chased; one who cannot is signalling what coordination will cost you later.

A proposal worth shortlisting includes:
  • the exact model code and a current photograph of the unit being priced;
  • an itemised inclusion/exclusion list against every option in the catalogue;
  • a dimensioned drawing showing shell, footprint and access clearances;
  • a jet layout plan and pump schedule;
  • the required electrical supply and total load, stated for the quoted configuration;
  • freight terms naming each leg of delivery and who bears cost and risk;
  • itemised warranty terms and a spare-parts route;
  • a named contact responsible for production coordination and site queries.

Send the same specification to three suppliers and compare on that structure. Where one quotation is materially cheaper, the reason will show up in this list — as an omitted heat pump, a sand filter moved to extras, or a freight price that stops at the port.

8. Coordinating the spa with the rest of the project

A swim spa rarely stands alone. It sits against paving and wall finishes, under a pergola or hardtop, beside loungers and storage for chemicals and towels, and within reach of the same electrical service as pool lighting. When those items come from different vendors, each handover becomes a coordination point where responsibility blurs.

Santerson operates as a China-based manufacturer and one-stop furniture and building materials supplier, in operation since 2008, with a published product range spanning swimming pools, outdoor furniture, sanitary fixtures, lighting, wall and ceiling finishes, flooring and cabinetry. Its stated service scope runs from design consultation and material selection through production, freight and door-to-door delivery to installation and after-sales support. For a poolside scheme that means the spa, the seating around it and the surrounding finishes can be specified against one set of drawings and delivered on one schedule.

Where a fixed shell size will not work for your space, the catalogue also lists a customizable shape outdoor spa covering square, round, oval and curved configurations. That is a different product route from WS-S04B, so decide which one you are quoting before you start comparing prices.

A single vendor makes coordination easier; it does not remove the need for an itemised inclusion list, a confirmed electrical requirement and freight terms you have read.

Putting it together

Assessing a proposal for WS-S04B is not about deciding whether 31 jets sound impressive or whether 3900 mm feels long enough. It is about forcing every supplier to describe the same machine, on the same site, under the same delivery terms — and then reading what they left out.

Work through the eight steps in order: fix the model code, test the dimensions against your access route, itemise the equipment list, reconcile the electrical load, define the freight boundary, pin down after-sale scope, score the completeness of the submission, and decide whether one vendor should carry the wider package. A quotation that survives that process is a quotation you can compare.

For configuration confirmation on WS-S04B — included equipment, electrical requirements, options and freight arrangements for your project — send your drawings and site details to the Santerson project team and request a written specification against the model code.

SANTERSON  |  View Outdoor Swim Spa WS-S04B  |  Browse the swimming pool range