A materials schedule only works when every line can be traced back to the same drawing revision. For bathroom packages that usually means ceramics are specified last, after furniture, flooring and joinery have already been locked in — and that is exactly where a single wall-hung basin becomes a project-wide problem. This guide walks through how we place the Wall Hung Ceramic Basin 1050WB, Luxury Gold Line Wall Mount Bathroom Sink inside a whole-project materials schedule, from the first room-by-room take-off to the final delivery list, so the specification survives value engineering and arrives on site complete.
Why the basin line decides the rest of the bathroom package
Wall-hung basins sit at the intersection of three trades: the wall framing that carries the concealed frame, the tiling that finishes around it, and the joinery or vanity — if any — that has to clear its projection. Change the basin after the tiling detail is drawn and you redraw the set-out. Change it after the joinery shop drawings are approved and you re-issue those too. Specifying the 1050WB early fixes three variables at once: a soft trapezoid wall-hung body in vitreous china with a gold line accent, fixed to the wall by its back panel rather than by a cabinet, with a pre-drilled faucet hole for a single tap fitting.
Because it needs no vanity carcass, the 1050WB also removes an entire schedule line — and the moisture exposure that comes with one — from guest bathrooms, villa secondary bathrooms and boutique hotel restrooms, which is where this type of basin is usually selected. The open floor beneath it is a housekeeping argument as much as a design one: there is no plinth or toe kick to trap water, and hard flooring can run through without a break.
Step 1 — Group the bathrooms into types, not numbers
Before any product code goes into the schedule, group the rooms. On hospitality and villa projects we normally see three categories, and each one takes a different basin decision:
- Principal / master bathrooms — vanity-led, statement finishes, usually a larger basin with counter space either side.
- Guest and secondary bathrooms — small footprints, high traffic, minimal joinery. This is where a wall-hung basin earns its place.
- Service and poolside bathrooms — durability and cleanability first, decorative detailing kept restrained.
Write the group into the schedule column instead of repeating a room number. The buyer, the tiling contractor and the furniture supplier all read that column differently, and a shared grouping is what stops the same code being ordered for a powder room and a spa bathroom.
Step 2 — Specify within one matching series wherever the rooms repeat
A materials schedule with one basin code per bathroom is difficult to price, difficult to deliver in consolidated shipments, and difficult to keep consistent when stock has to be replenished mid-project. The cleaner approach is to buy inside a matched sanitary collection so that the gold line detailing carries across rooms without looking repeated.
The 1050WB belongs to the 1050 series, which is why it can sit in the same schedule block as its siblings:
- Wall Hung Ceramic Basin 1050WC, Luxury Gold Line Wall Mount Sink — the tall, vertical silhouette, used where the basin is meant to read as a feature piece rather than a utilitarian one.
- Freestanding Pedestal Basin 1050B, Luxury Gold Line Ceramic Stand Basin — the floor-supported option for rooms where the wall construction will not take a wall-hung loading arrangement.
- Washdown One Piece Toilet 1050A, Luxury Gold Line Ceramic WC — the coordinating WC, with both P-trap and S-trap rough-in options to suit different drainage layouts.
The practical benefit is not decorative. When three rooms share one series, the same glaze, the same gold line treatment and the same supplier batch cover them, so colour and finish variation between rooms stops being a snag-list item at handover.
Step 3 — Put the fixing method in the schedule, not just the model number
Two projects can order the same basin and get two very different site outcomes, because wall-hung ceramics depend on what is behind the finish. For the 1050WB the note that matters to the site team is how it is retained: a back-panel fixing to the wall, with no cabinet taking the load. That single line tells the framing contractor where reinforcement is needed, tells the tiler where the sealant joint falls, and tells the plumber where the waste and supply connections have to land relative to the finished face.
We record three things against the line:
- Fixing type — wall-hung, back-panel fixed, no vanity support.
- Wall build-up — finished face dimension, and whether the partition is masonry, steel stud or timber.
- Tap arrangement — pre-drilled single faucet hole, so the mixer is scheduled to match rather than chosen on site.
Dimensions for this basin are published as 495×440×390 mm. Treat that as the design figure and confirm it against the current technical sheet before the set-out drawings are issued — trap positions, rough-in and any standard-related claims should always be checked against the final documentation rather than carried forward from a brochure.
Step 4 — Cross-reference the schedule so trades see their dependencies
A materials schedule that lists products in isolation gets read once and forgotten. A schedule that cross-references gets used. Alongside the basin line we add pointers to the packages that have to agree with it: bathroom sanitary fixtures for the ceramic package itself, floating vanity and undermount basin lines for the rooms where a wall-hung basin is not the answer, and vanity lighting for the mirror zone above it. That way, if the 1050WB is dropped from one room during value engineering, the dependent lines are visible in the same view and can be revised together.
This is also where you protect the design intent. If a reviewer objects to the gold line, the schedule should already show which alternative basins keep the same proportions and which change the whole character of the room — otherwise the substitution happens on site with no drawing behind it.
Step 5 — Consolidate the ceramics into the wider procurement package
Ceramics ordered separately from furniture, flooring and finishes arrive separately, get inspected separately, and are checked against separate documents. Coordinating interior fixtures with the rest of the fit-out under one supplier keeps the schedule in one place: the same revision number applies to the basin, the joinery it sits beside, the flooring beneath it and the lighting above it. Our furniture and building materials project procurement service exists for exactly this situation — one coordinated package across bathroom ceramics, cabinetry, wall and floor finishes, lighting and loose furniture.
For projects outside China, the practical gain is in freight planning. Wall-hung basins are fragile, bulky and easy to damage when they travel as an afterthought shipment alongside a full container of furniture. Packing them within the coordinated package means crating is designed around them, and the unloading sequence matches the installation sequence rather than fighting it.
Step 6 — Add a pre-order approval line to the schedule
The last column most schedules omit is the one that prevents rework: a sample or mock-up reference against the basin line. For a decorative piece like this, where a gold line detail sits against a white glaze under a project's own lighting, we recommend approving a physical unit before the full quantity is released — ideally installed in a mock-up bathroom next to the chosen tile, tapware and mirror light.
That one line item typically resolves more disputes than any amount of specification writing: it settles glaze tone, how visible the gold line reads at sitting height, and whether the trapezoid proportions work against the actual wall width.
A short checklist for the schedule
- Bathroom grouped by type, not only by room number.
- Basin specified inside one matched series wherever rooms repeat.
- Fixing method and wall build-up written against the ceramic line.
- Tapware scheduled to match the pre-drilled hole arrangement.
- Cross-references to vanity, countertop and lighting lines in the same view.
- Sample or mock-up approval recorded before bulk release.
- Dimensions confirmed against the current technical sheet at set-out stage.
If you are assembling a bathroom package for a hotel, villa or multi-unit project and want the ceramic lines coordinated with the rest of the fit-out rather than tendered separately, send us your schedule and drawings. Our team will confirm which rooms suit a wall-hung basin, which need the floor-supported alternative, and what the coordinated package looks like delivered — see our turnkey interior project solutions or contact us directly to start the review.