A swim spa that fits an eight-metre footprint looks simple on a brochure until the quotation arrives. Two units with similar external lengths can differ widely in jet count, pump arrangement and installed electrical load, and those differences decide whether the unit suits a villa terrace, a resort garden or a hotel wellness area. The Outdoor Swim Spa WS-S08CT is one model in SANTERSON's configurable outdoor swim and hydrotherapy range. Below is the comparison checklist we suggest using when evaluating it, so that quotations from different suppliers actually describe the same product.

Start with the footprint, not the feature list

The catalog lists WS-S08CT at 8000 × 2400 × 1420 mm. Before anything else, put those three numbers onto your site drawing. Length and width determine the slab, the clearance for maintenance access and the transport route to the position; depth determines water volume, seating posture and how usable the swim lane feels for an adult of a given height. A one-metre difference in length between configurations can change whether two people can sit comfortably in the hydrotherapy zone while someone else swims against the current.

Compare the footprint with the other eight-metre-class models we publish, because internal layout differs even when length is close:

  • WS-S08CT — 8000 × 2400 × 1420 mm; swim training system 1 set; jet total 35 pcs; water pump 1 pcs; filter pump 1 pc; control system 1 set; LED lights 6; total power 8.35 kW.
  • WS-S08T1 / WS-S08T2 — 7800 × 2200 × 1500 mm; swim training system 1 set; jet total 50 pcs; water pump 2 pcs; filter pump 1 pc; total power 9.55 kW.
  • WS-S08M — 8020 × 2260 × 1280 mm; jet total 58 pcs; water pump 2 pcs; filter pump 1 pc; total power 6.95 kW; no swim training system listed in the captured specifications.
  • WS-S08B — 7800 × 2200 × 1500 mm; jet total 98 pcs; water pump 4 pcs; filter pump 2 pc; control system 2 sets; waterfall feature; total power 14.6 kW.

Read as a set, these four lines show the trade-off clearly. The WS-S08CT sits at the lower electrical load end of the group while still including a swim training system, which matters if your site's power supply is already committed to other building services. If jet count and hydrotherapy intensity drive the decision, the same catalog range offers configurations with substantially more jets at a higher installed load.

Check what the swim training system actually delivers

WS-S08CT is listed with one swim training system set, which places it in the exercise-first category rather than the lounge-first category. When you compare suppliers on this point, ask three specific questions instead of accepting the phrase "swim current". First, how is the flow generated — a dedicated nozzle assembly or a repurposed jet line? Second, is the flow adjustable, and by what means? Third, what clear swim length remains once the seating and jet zone are taken into account at the catalog depth of 1420 mm?

A buyer who intends lap training for rehabilitation or daily fitness should treat the swim lane as the primary requirement and the spa seating as secondary. A hospitality wellness room, by contrast, often needs throughput: guests rotating through a short session. Those two uses justify different configurations even at identical external dimensions.

Compare jet count together with pump arrangement

Jet totals are the number suppliers quote most readily and interpret least carefully. WS-S08CT is specified with 35 jets, one water pump and one filter pump. A higher jet total usually implies more pumps and a higher total power figure, which is exactly what the comparison list above shows across the range. What you want in writing is the split between hydrotherapy jets and the swim current supply, plus which pump serves which function, because that determines whether massage intensity drops when the swim system is running.

Reconcile total power with your electrical design

The catalog figure for WS-S08CT is 8.35 kW total power. Treat that as the starting point for an electrical conversation with your engineer, not as the finished answer. Heating method changes it substantially: a heat pump option draws differently from resistive heating and suits year-round use in cooler climates far better. Insulation, which appears in the catalog options list, is what keeps that load steady once the water is at temperature. Ask for the wiring diagram, breaker sizing and any requirements for dedicated circuits before you place the order, and confirm the same details against the final configuration rather than the base model.

Water treatment: ozone standard, UV optional

Ozone appears in the features shown for WS-S08CT. UV sterilisation is a catalog-listed option across the swim spa range rather than something to assume on every configuration. For a project where several users share the water daily, decide early whether UV belongs in your specification, because retrofitting after production adds cost and delay. Filtration is another decision point: the base specification lists a filter pump, while sand filtration appears among the catalog options. Which one you need depends on placement — a unit beside a landscaped garden pool deck collects far more debris than one under cover.

Lighting and control are project details, not decoration

WS-S08CT is listed with six LED lights and one control system. In a villa the control position is a matter of convenience; in a hotel or resort it affects how staff operate the unit, whether settings can be locked, and how the lighting coordinates with surrounding landscape lighting. Confirm the control interface type and mounting location on the drawing before production, and specify which zones the LED fixtures illuminate if you are matching an existing lighting design.

Options to price into the quotation from day one

The catalog lists these options for the range: control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so each item needs confirming against your chosen configuration. Steps and insulation in particular are cheap to add at production and awkward to solve later on site.

How a one-stop supplier changes the comparison

A swim spa rarely arrives as an isolated purchase on a project. The surrounding deck, wall cladding, outdoor furniture and lighting are usually specified by the same team, and mismatched suppliers create gaps in responsibility. As a China furniture and building materials manufacturer, SANTERSON supplies swim spas alongside outdoor furniture collections and interior fixtures, with custom/OEM service, logistics and door-to-door delivery, installation support and after-sales service handled under one project scope. For villa and hospitality buyers coordinating several trades, that reduces the number of interfaces you have to manage — see our wider product range for what sits alongside the spa.

A short checklist before you sign

  • Confirm external dimensions against the slab and access route, including maintenance clearance.
  • Ask how the swim current is generated and whether it is adjustable.
  • Get the jet split and pump assignment in writing, not just a jet total.
  • Reconcile total power with your supply; specify heating method and insulation.
  • Decide on UV sterilisation and filtration type before production starts.
  • Fix control interface type and position on the drawing.
  • Confirm included equipment and electrical requirements for the exact configuration you ordered — catalog specifications describe the standard build, and options change them.

Comparing WS-S08CT this way keeps the conversation with any supplier on measurable ground: dimensions, current generation, pump duty, installed load and treatment method. Send us your site drawing and intended use, and we will confirm which configuration in the range matches both.