An outdoor swim spa sits somewhere between a plunge pool, a hydrotherapy tub and a lap pool, so two units that look almost identical on a brochure can end up with very different site works, running costs and daily usability. If you are specifying Outdoor Swim Spa WS-S04B for a villa terrace, a resort garden or a private wellness area, the useful comparison is not price against price. It is whether the specification matches the plot, the users and the maintenance routine you can actually sustain. Below is the checklist we suggest using before you request a final quotation.

Start with the footprint, not the jet count

The catalogue lists WS-S04B at 3900 × 2200 × 1450 mm. Three numbers decide whether the unit fits your site at all: the external length and width for the slab and clearances, and the 1450 mm depth for both water volume and how adults sit in it. A deeper shell suits seated hydrotherapy and gives a more comfortable resting position, while shallower formats in the same range trade depth for a longer or wider basin.

Compare the external dimensions against your prepared base with working clearance left on at least one side for the equipment access and future servicing. Then compare internal water depth against who will use the spa: lap-style training, children playing, or adults using jets for recovery all want different geometry. Ask the supplier to confirm which measurements are external shell and which are internal water depth before you brief your civil contractor.

Read the pump and jet layout as a system

The WS-S04B specification sheet shows 3 water pumps, 1 filter pump, a total of 31 jets including 6 water columns, and a listed total power of 10.35 kW. Those figures only mean something as a group. Jet count alone tells you very little; jet type and position tell you far more. Water columns deliver a directional, full-body stream, while smaller jets give localized pressure. A configuration built around several columns behaves differently from one that spreads many small jets across the seating ledges.

For comparison, sibling models in the same range show different balances: WS-S04 lists 26 jets with 4 water columns and a listed total power of 8.25 kW, while WS-S04X shows a higher jet count at 85 pieces on a shallower 950 mm shell. Neither is "better". They point at different use cases, and the difference in listed total power is the number your electrical and operating budget should be built around.

SpecificationWS-S04BWS-S04WS-S04X
Catalogue dimensions (mm)3900 × 2200 × 14504090 × 2200 × 11103990 × 2260 × 950
Water pumps / filter pump3 pcs / 1 pc3 pcs / 1 pc3 pcs / 1 pc
Jets31 pcs, incl. 6 water columns26 pcs, incl. 4 water columns85 pcs
Listed total power10.35 kW8.25 kW8.85 kW
Features shown on the pageWater jets, LED lighting, OzoneWater jets, LED lighting, Ozone, WaterfallWater jets, LED lighting, Ozone, Waterfall

Figures above are transcribed from the published catalogue pages for each model. Treat them as a starting point and confirm the exact configuration in writing on your proforma invoice, because options and included equipment change between builds.

Check what is included before you price the extras

Optional accessories listed for this range include control systems, UV sterilization, additional water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so a low base quotation can quietly become a much higher delivered figure once the essentials are added. Work through each item and ask three questions: is it included in the quoted price, is it compatible with this specific shell, and what does it change in running power and maintenance?

  • Heat pump and insulation — determine how the water is heated and how fast it loses heat overnight. These matter most where the spa is used year-round rather than seasonally.
  • Filtration type — a standard filter pump and a sand filtration setup carry different cleaning routines and consumable costs.
  • Water treatment — ozone is shown as a feature on this model; ask whether UV sterilization is offered as an addition and how the two interact in the control logic.
  • Steps and access — steps affect both the entry height for users and the space needed around the shell.
  • Control system — confirm how many zones are controlled, and what happens if a controller needs replacing in the field.
Electrical note: the listed total power is the figure to design around, but supply capacity, protection devices and earthing must be confirmed with a local licensed electrician against your own installation requirements. Ask the supplier which pumps and heaters are energized simultaneously before sizing the circuit.

Confirm site preparation and delivery scope in writing

Most swim spa disputes are not about the product; they are about the boundary between what the factory supplies and what happens on site. Before ordering, get written confirmation of: the prepared base specification and load expectations, drainage arrangements, who supplies and installs the steps or surrounding decking, and whether the quoted price covers door-to-door delivery, customs paperwork and on-site installation.

SANTERSON describes a turnkey workflow covering design consultation, production, logistics and door-to-door delivery, then installation and after-sales support. That scope is useful for project buyers who want one supplier handling the swim spa alongside other outdoor products, but you should still confirm transit terms, duties and installer availability for your own country on a case-by-case basis rather than assuming them.

Compare the whole outdoor package, not one item

A swim spa is rarely specified alone. Poolside lounging, shade structures and wet-area flooring usually follow in the same purchase order, and buying them together simplifies finishes, delivery windows and warranty contacts. The catalogue range includes Luxury Outdoor Swim Spa with Massage Jets, LED & Water Features for larger layouts, Customizable Shape Outdoor Spa, Personalized Hydrotherapy Pool where the plot demands a bespoke form, and Modern Aluminum Outdoor Dining Set & Sun Lounger for the seating immediately around the water. Aluminium frames and teak-look tops in those collections are chosen because they sit outdoors next to splashed water without the maintenance load of solid timber.

If you are furnishing a resort or villa project, matching the swim spa shell finish to the surrounding lounger frames and wall finishes is easier when one supplier handles both. Our swimming pool category lists the models in this range with their published specifications so you can shortlist on dimensions and jet layout before talking to us.

Five questions that settle the comparison

  • Does 3900 × 2200 × 1450 mm fit the site with servicing clearance, and is the depth right for the users?
  • Which pumps are included in the quoted price, and what does the listed total power mean for expected use patterns?
  • Are heat pump, insulation, filtration and water treatment quoted as included or as extras?
  • Who prepares the base, connects drainage, installs steps and commissions the system on site?
  • Which items are stocked as spare parts, and how are replacements shipped to your location?
Send us the model reference (WS-S04B), a sketch of the intended location with access notes, and your rough usage pattern — seasonal or year-round. We will confirm the configuration, included equipment and electrical requirements for that build, and quote it together with the surrounding outdoor furniture and finishes if required.