An outdoor dining programme only works when the furniture arrives ready to be set out, levelled and handed over. Below is the installation plan we build around our Extendable Aluminum Slat Dining Table, Matching Wicker Dining Set & Bar Table Stool Set — the rope-woven outdoor family that covers three layouts at once: an extendable slat-top dining table, a square dining set for terrace corners and a high bar set with stools for pool bars and café frontages. The same plan applies whether you are furnishing a resort outdoor restaurant, a holiday villa or a coastal café.
1. A Layout Drawing Before the Furniture Is Made
The first deliverable in the plan is a set-out drawing, not a container. Because this series mixes dining height and bar height on one terrace, the drawing has to show clearances for both: circulation behind pulled-out dining chairs, walking space around bar stools, and enough room at the extension end of the slat table so it can actually be opened during peak season without blocking a path or a door swing.
Send us your terrace dimensions, entrance widths and any fixed elements — planters, railings, shade structures, pool coping — and our design team returns furniture layouts and 3D visual renderings under our Interior Design Services. That drawing becomes the basis for the packing list, so what arrives matches what was planned.
2. Site Conditions Recorded in Writing
Installation problems on hardstanding almost always trace back to ground that nobody measured. Your plan should record, before production:
- The finished surface under the dining and bar zones — pavers, timber decking, screed or gravel — and how level it is across the full set-out area.
- Whether the area sits in a salt-spray zone. The metal surfaces in this series are powder coated to stand seaside salt spray, but the coating still needs to be matched to the exposure you describe.
- Drainage and fall away from the building, so water does not pond under slat tops or around stool feet.
- Wind exposure on exposed terraces and roof decks, and whether any item needs anchoring or a fixed position.
- Delivery access: lift sizes, gate widths, stair flights, crane or hoist needs, and how far the crates must be carried by hand.
3. What Is in Each Crate and How It Arrives
A plan that does not name the contents is not verifiable at the dock. Our packing list states, per crate, the component, quantity and finish, so your site team can check the delivery against the drawing on day one. For this series that means slat table tops and extension leaves, frames, woven-rope chairs, bar stools, teak-look or solid top panels, fixings and hardware sets — each grouped by the zone it belongs to, dining or bar.
Freight is arranged under our Logistics & Door-to-Door Delivery service: sea, air or rail forwarding, commercial invoices, packing lists, certificates of origin and the customs paperwork your broker needs, with shipment tracking and container loading planned so crates unload in installation order.
4. Assembly Sequence on Site
Write the sequence into the plan so whoever supervises the day is not improvising:
| Stage | What happens | Who checks it |
|---|---|---|
| Unpack and stage | Crates moved to the correct zone, contents counted against the packing list, protective packaging kept until inspection is complete. | Your site representative with our coordinator |
| Frame assembly | Aluminium frames bolted up on a level surface; all fixings tightened to the torque in the instruction sheet; extension mechanism worked open and closed before loading. | Installer |
| Top and slat fitting | Slat tops, extension leaves and table panels seated and fixed; gaps checked for even alignment across the whole run. | Installer |
| Rope-woven seating | Woven-rope chairs and bar stools assembled onto their frames; seat height and level checked with the intended cushion. | Installer |
| Set-out to drawing | Items placed on the finished surface, levelled individually, clearances re-measured against the set-out drawing. | Site supervisor |
| Inspection and handover | Snag list closed out, spare fixings handed over, care instructions issued, sign-off recorded. | Both parties |
5. Levelling and Fixing Rules
State the levelling rule explicitly. On an outdoor hardstanding, each table and stool must sit solid on all contact points with no rocking, which usually means adjustable feet or packing shims rather than relying on the sub-base being perfect. Where a set is exposed to strong wind, agree in advance which items are anchored and what fixing detail applies to that surface — timber decking and pavers take different fixings.
Also state what must not be done: do not tighten slat assemblies with the table resting on an uneven base, and do not force an extension leaf that has not been checked for debris in the runners.
6. Spare Parts, Spares Kit and Care Notes
Include a spares kit in the order rather than chasing single bolts later: spare fixings, a set of feet or glides, and replacement hardware for the extension mechanism. Our Installation & After-sales Support service covers on-site installation, inspection and snags, warranty coverage, spare parts and replacement, and ongoing maintenance.
Hand over a one-page care sheet at completion: how to clean powder-coated frames and woven rope, how often to check fixings in a commercial setting, how to store or cover cushions between seasons, and what to do if a teak-look surface is scratched. Commercial operators who know the routine inspect on a schedule instead of waiting for a complaint.
7. Customising the Series Before It Is Manufactured
The installation plan is easier to hold if the product was built for your space. Table dimensions, frame tones and rope colours can be adjusted to match project design schemes under our Custom & OEM Service, including bespoke finishes and prototyping. Confirm the final dimensions in writing before production starts, because those dimensions are what your set-out drawing and clearances depend on.
If a single series is not enough for the whole outdoor programme, matching pieces from the same design language keep dining and bar zones consistent — for example the Aluminum Outdoor Dining Set & Bar Table Stool Set with Teak Accents for a sled-base frame with teak details, or the Rope Weave Outdoor Dining Set & Bar Table Stool Set with Teak Armrest for an oval dining layout paired with a high bar set.
8. One Named Supplier Across Design, Production and Handover
Splitting design, manufacturing, freight and installation across four vendors is where handover dates slip. As a one-stop furniture and building materials supplier, we run the six-stage workflow used on our villa, hospitality and office projects: consultation, design and planning, production, logistics, installation and after-sales. One coordinator holds the packing list, the drawing and the snag list, so the person who specified the extendable table is the person who signs it off on site.
That also matters when outdoor furniture is ordered alongside everything else in the project — furniture series, pergolas and gazebos, lighting, flooring and wall finishes — because one delivery window and one installation crew can be planned across all of it.
Installation Plan Checklist
- Set-out drawing with dining and bar clearances marked, extension swing shown.
- Site conditions recorded: surface type, levelness, drainage, salt exposure, wind, delivery access.
- Packing list per crate with component, quantity and finish.
- Written assembly sequence and levelling rule for the finished surface.
- Anchor detail agreed for exposed positions, matched to the sub-base.
- Spares kit in the order: fixings, feet, extension hardware.
- Care sheet issued at handover; snag list closed and signed.
- Custom dimensions, frame tones and rope colours confirmed before production.
Send us your terrace drawings
Share the set-out area, exposure conditions and target handover date, and we will return a furniture layout, a quotation with a crate-by-crate packing list and an installation plan for the extendable slat dining table, wicker dining set and bar table stool set — produced by SANTERSON, a China-based furniture and building materials manufacturer working on villa, hospitality and office projects.
Contact: PHILLIP · Phone/WhatsApp +86-13928214007 · Email santerson@qq.com
Material, coating and weather-resistance descriptions follow the manufacturer's product specifications for this series; confirm exposure requirements and any local installation or import requirements for your project at quotation stage.