A swim spa is not an off-the-shelf purchase. The difference between a smooth delivery and a stalled project usually comes down to what the buyer can already answer in the first enquiry. If you are evaluating Outdoor Swim Spa WS-SP600-MS for a villa, resort or residential development, the notes below cover the information a manufacturer needs from you — and what you should ask them to confirm in return.

1. Site dimensions and access route

Before anything else, send the supplier your measured space, not an estimate. The catalog lists this model at 5900 × 2500 × 1600 mm, so your slab or deck needs to accommodate that footprint plus clearance for the equipment compartment, filtration access and entry steps.

Also describe how the shell physically reaches its final position. A ground-floor garden setting with a clear gate is a very different quote from an upper terrace, a rooftop, or a courtyard where a crane or hoist may be required. Include photos of the site and note any overhead obstructions, steps, narrow passages or finished surfaces that need protection.

2. Structural and ground conditions

Water is heavy, and a filled spa transfers that load to whatever supports it. Tell the supplier whether the unit will sit on a prepared concrete slab, a raised deck, a plinth or indoors, and share what the structural engineer has specified for that surface. If the base does not exist yet, say so — the required preparation differs between an in-ground recess, a semi-recessed installation and a fully above-ground placement.

Drainage and overflow provision belong in the same conversation, along with any local consent or permit requirements your project is subject to. We can advise on the technical envelope of the unit; approval responsibility sits with your local authority and design team.

3. Power supply and electrical capacity

The catalog shows a total power figure of 11.55 kW for this configuration, which is well beyond an ordinary socket circuit. Before requesting a quotation, confirm what your site can actually deliver: available supply capacity, single-phase or three-phase, the distance from the distribution board to the spa location, and whether a dedicated circuit and isolator have already been planned.

Electrical requirements vary with the selected configuration, so ask the supplier to state them for your exact specification and hand those figures to a qualified local electrician. Local wiring rules are enforced locally — that work must be signed off by a licensed electrician in your region.

4. Configuration and optional equipment

This model sits within our configurable outdoor swim and hydrotherapy range, so the specification you enquire about should be written down rather than assumed. The catalog records a control system, a swim training system, a water pump, a filter pump, 29 jets and 4 LED lights for this configuration, with water jets, LED lighting, ozone and a swim training system shown as the headline features.

Optional items listed in the catalog include additional control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps. Tell us which of these you want and which your local climate or usage pattern makes unnecessary — a spa used year-round in a cool climate has a very different heating and insulation package from one used seasonally.

Item to confirmWhy it matters
Included vs optional equipmentDefines the quotation and what arrives on site
Total power and supply typeDetermines electrical preparation and running cost
Filtration and sanitation methodAffects maintenance routine and consumables
Insulation packageDetermines suitability for cold-weather operation
Steps, cover and access itemsFrequently omitted from an initial quote

5. Intended use and who will operate it

Be explicit about how the spa will be used. Daily swim training, occasional hydrotherapy, a hotel wellness facility or a shared residential amenity each point to different jet layouts, seating arrangements and maintenance expectations. A facility operated by hospitality staff needs a cleaning and water-treatment routine that a non-specialist can follow, so ask what daily and weekly upkeep actually involves before you commit.

Usage intensity also affects the service conversation: which parts are consumables, how replacements are supplied, and who performs maintenance in your country. Get those answers in writing at quotation stage rather than after installation.

6. Delivery, import and handover

For an international order, the buyer's brief should state the delivery address, the Incoterms you expect to work with, and who is handling customs clearance in the destination country. Tell the supplier your required site date — that figure drives production scheduling and the freight mode, whether sea, air or rail.

Our logistics service covers freight forwarding, export paperwork, packaging and container loading, shipment tracking and door-to-door delivery. Import duties, local taxes and destination-side permits are set by your country's rules, so we recommend confirming those costs with your own customs broker before the order is placed.

A practical test: if a supplier answers your questions with a price alone, the specification is not settled. A useful reply restates your site conditions, states the equipment list, and flags what you still need to arrange locally.

What to send in your first enquiry

  • Measured site plan with photos and the access route from the street
  • Structural support arrangement and drainage provision, or the design intent if not yet built
  • Available power supply: capacity, phase type, distance to the spa location
  • The model and configuration you are considering, plus the options you want
  • Intended use, operator, and target on-site date
  • Delivery city and port, and who handles import clearance

Where this model fits in the range

If your space or budget points somewhere else, the wider swimming pools and swim spas catalogue covers compact through long-format units with different jet counts and power loads, so the footprint and electrical demand can be matched to the site rather than the reverse. Where a standard shell does not suit the space, our customizable shape outdoor spa supports square, round, oval and curved layouts with an acrylic shell for gardens, terraces and leisure areas.

SANTERSON has manufactured furniture and building materials for villa, hospitality and office projects since 2008, and supplies swim spas as part of a wider one-stop package — which means poolside loungers, pergolas, outdoor dining sets and the surrounding landscape furniture can be produced, shipped and tracked under one programme instead of several separate suppliers.

Send your site measurements, power details and target installation date to PHILLIP via the contact page, WhatsApp +86 13928214007 or santerson@qq.com. You will receive a specification sheet for the configuration you select, together with the items your local team needs to prepare on site.