An outdoor swim spa is one of the few products in a villa or resort package that sits across three disciplines at once: landscape design, civil works and building services. The unit itself arrives as a finished shell with pumps, jets and controls already fitted, but everything around it — the slab, the pit, the power feed, the drainage, the deck edge — is decided by other trades on your drawings. When those decisions are made without the product data, the spa either will not fit through the access route, will not sit level, or will not be serviceable after handover.
This guide walks through how we coordinate Outdoor Swim Spa WS-SP600-MS with architectural and landscape drawings, and what the site has to deliver before the unit is set in place. It applies whether you are specifying the unit yourself or sending us a drawing pack for review.
1. What the product data sheet gives you at specification stage
Before any drawing is marked up, the design team needs the catalog dimensions and the equipment list for the exact model variant. For WS-SP600-MS the catalog lists a footprint of 5900 × 2500 × 1600 mm. That single line drives four separate drawing items: the clear opening on the access route, the slab outline, the position of the plant and control zone, and the setting-out dimensions for the surrounding deck.
| Drawing item | What to set out from the product data |
|---|---|
| Access and lifting route | Clear width and height of gates, side passages and any turning space, checked against the 5900 × 2500 × 1600 mm envelope including packaging. |
| Slab or plinth | Rigid, level supporting area extending beyond the shell on all sides, with the finished level marked relative to the deck finish. |
| Deck and coping line | Offset from the spa shell to the paving edge, so the cabinet panel and access hatch are not built in behind fixed tiling. |
| Electrical run | Route from the distribution board to the control position, sized by your electrical engineer from the connected load for the agreed configuration. |
Catalog figures are transcribed from the product page and describe the standard catalog configuration. Options such as heat pumps, sand filtration, extra insulation or additional steps change what has to be accommodated on site, so the final dimension and load schedule should always be confirmed against the order-specific configuration drawing.
2. Reading the equipment list against the services drawings
WS-SP600-MS is listed with a control system, a swim training system, a water pump, a filter pump, 29 jets and four LED lights, with a catalog total power figure of 11.55 kW. The same page also lists optional accessories — UV sterilisation, heat pumps, sand filtration, insulation and steps — which are not part of that baseline number.
Two points matter on the services drawings:
- The power figure is configuration-dependent. A heat pump or an upgraded filtration system changes the connected load. Your electrical designer should size the circuit, protection and any dedicated isolator from the confirmed configuration schedule, not from a catalog line taken out of context.
- Service access has to survive the finished detail. Pumps, filters, the control system and the ozone unit all need a reachable position. If the cabinet side is later clad in fixed stone or tiled over, the plant becomes unreachable without demolition. Show an access hatch or a removable panel on the deck plan.
Where a project needs a different equipment mix, we produce the unit to the agreed specification rather than forcing a site into a catalog build. That is also the point at which we compare WS-SP600-MS with the closely related Outdoor Swim Spa WS-SP600: the two share the same catalog footprint, but the jet count and total power differ between them, so the electrical and plant provisions must follow whichever model is actually on the schedule.
3. Site requirements to confirm before the unit ships
The following items should be closed out on paper before production is released, because each one becomes expensive to change afterwards:
- Level and support. A full-perimeter bearing surface, compacted and levelled, with the finished slab level recorded on the setting-out drawing. An uneven base shows up later as stress on the shell and as water line that looks wrong even when it is not.
- Drainage and overflow. Where deck wash-off and any drain-down water go, and whether a drain or soakaway is required at the spa position.
- Water supply point. A fill point within reach of the unit, plus space for hose connection during commissioning and routine top-up.
- Electrical route and isolation. Conduit in the ground before paving is laid, with a clearly labelled isolator positioned outside the splash zone as determined by your electrical contractor.
- Cranage or manual set. Whether the delivery position is reachable from the truck, and whether a crane, gantry or a manual carry along a protected path is needed. This has to be decided while the access route is still on the drawing.
- Deck finishes and tolerances. The gap detail between spa shell and paving, and which trade owns that joint.
4. Where custom geometry changes the coordination job
Not every pool deck suits a rectangular 5900 mm shell. On terraces with curved edges, or where the spa has to sit inside an existing architectural feature, a shaped unit is often the cleaner answer — our Customizable Shape Outdoor Spa covers square, round, oval and curved outlines so the water feature follows the landscape line instead of fighting it. For villa and resort schemes where the spa is the visual centrepiece rather than a lap-training fixture, the Luxury Outdoor Swim Spa with Massage Jets, LED & Water Features is the reference point for jet layouts and water features that read well from the terrace as well as from inside.
Custom geometry does not remove the site requirements above — it simply moves them. A curved shell needs a different setting-out grid, and any raised or semi-recessed installation needs the retaining detail drawn before the shell is manufactured, not after.
5. How the drawing review runs on our side
Send us the landscape plan, the sections through the pool deck and the electrical layout, and we mark them up against the selected configuration. That review covers the access route, the bearing surface, the plant and hatch positions, the conduit routes and any option items that change dimensions or loads. It sits inside our Interior Design Services, which include space layout planning, product specification and project design coordination covering drawings, production coordination and on-site guidance.
Because the spa rarely travels alone on a package order — it usually moves with swim spas, loungers and poolside furniture, and often with the surrounding paving, screens and lighting — the same coordination pass also fixes delivery sequencing. A spa set on site in week six is useless if the deck edge is still being decided in week twenty.
Documents that make the review faster
Landscape or pool-deck plan at 1:50 or larger; sections through the intended spa position; finished levels schedule; electrical layout with distribution board location; access photographs of gates and side passages; and the client's brief on intended use — daily lap training, hydrotherapy, children's play, or a mix. With those in hand we can return a marked-up coordination drawing rather than a list of questions.
6. The practical checklist for project teams
- Freeze the model and configuration before setting-out drawings are issued, so dimensions, jet count and power load all come from one source.
- Have your structural and electrical engineers size slab, circuit and protection from the order-specific schedule; catalog figures are a starting point for design, not the design itself.
- Show plant and control access on the deck plan, with a hatch or removable panel that survives the finished finish.
- Confirm the delivery route and lifting method while it is still cheap to change on paper.
- Sequence the spa against paving, screening and landscaping dates in the programme, not just against the purchase order date.
If you have drawings at concept or tender stage, send them over with your intended use case and we will confirm which configuration fits the space, what the site has to provide, and where on the programme the unit should land. As a China-based manufacturer and one-stop supplier of furniture and building materials, we handle the same coordination for villa, hospitality and office packages end to end — specification, production, turnkey project delivery, logistics and on-site support.
Send your pool-deck drawings for a configuration and site-requirement review.
Contact PHILLIP — Phone / WhatsApp +86-13928214007 · Email santerson@qq.com · Enquiry page