A ceramic toilet is one of the few bathroom items where a batch problem surfaces after the tiles are laid and the grout has set. Ordering Washdown One Piece Toilet 1004A, Modern Ceramic Bathroom Toilet for a villa or hotel room floor is straightforward; making sure the production run matches what your design team actually approved takes a short, disciplined sample review. Below is the check sequence we ask buyers and project teams to work through before mass production begins.

What "finish sample" means for this product

For a vitreous ceramic fixture there is no paint or laminate to swatch, so the sample review concentrates on four things: glaze colour and gloss, surface texture, silhouette, and the geometry that decides whether the unit fits your drainage. The 1004A is described as a square-rounded one-piece form in a dense glossy glaze, with a washdown flushing mechanism and two plumbing options — P-trap wall drain (180mm rough-in) and S-trap floor drain (250mm rough-in). Those four points are exactly what the sample has to confirm.

Two practical cautions before you start. First, every measurement on a fired ceramic piece carries kiln variation, so check dimensions with a tolerance band rather than treating one number as absolute; the technical data sheet for the specific batch is the reference, not a screenshot of the listing. Second, never judge glaze colour from a phone photograph. Ceramic gloss reflects the light source around it, and camera processing shifts whites noticeably. Colour and gloss judgements need a physical piece under controlled light.

Step 1 — Confirm the sample is the version you will receive

  • Ask for the sample to be taken from the production tooling and glaze line intended for your order, not a hand-made display piece.
  • Get the model marking on the piece photographed — 1004A, plus the trap variant being sent — so you can match sample paperwork to delivery paperwork.
  • Request the current technical data sheet for that batch and check it lists the rough-in dimensions, overall size and flushing details you are specifying in your drawings.
  • Confirm which trap you have sampled. If your project mixes wall-drain and floor-drain bathrooms, request one P-trap sample and one S-trap sample rather than assuming the body is interchangeable.

Step 2 — Inspect the glaze under real conditions

  • Colour match: place the sample against your bathroom palette — wall tile, basin, countertop and any matched fixtures from the same sanitary series. Compare in daylight and under the actual luminaire you have specified, not only in a showroom.
  • Gloss uniformity: view the tank lid, bowl shoulder and underside at a low angle. Look for dull patches, orange-peel texture, runs or thin glaze on edges and internal returns.
  • Surface defects: check for pinholes, black specks, bubbles, chips on the rim and base, and rough unglazed areas where they would contact the floor or wall fixing.
  • Cleanability in practice: run your finger across the glaze and note drag; a dense, fully vitrified surface should feel glass-smooth. This matters on high-turnover hotel rooms where housekeeping scrubs daily.

Step 3 — Check the silhouette against your room

One-piece construction is part of the specification here: the tank and bowl are integrated, which removes the gap where dirt collects and gives a cleaner line. Bring the sample into the actual bathroom or set it against a full-size layout print, and check:

Step 4 — Verify flushing and drainage before sign-off

This is the step most buyers skip, and the one that causes the most rework. With the sample on site or in your mock-up bathroom:

  • Measure the finished rough-in on site — wall drain height for P-trap, floor centre offset for S-trap — and compare it to the data sheet for the sampled variant. Do this against the completed floor build-up, not the structural slab.
  • Dry-fit with the intended connector or seal. Note whether the trap outlet aligns without forcing the body out of plumb.
  • Check the flush action with water connected: rim wash coverage across the bowl, evacuation in one pass, refill behaviour and shut-off noise. Washdown systems are chosen for strong single-pass performance; confirm it on your water pressure, not the factory's.
  • Confirm supply connection type and that your stop valve and inlet suit it.
If the project spans several room types, build one mock-up bathroom per type. A toilet that clears a villa master bathroom can foul a compact guest WC once door swings and partitions are added.

Step 5 — Compare against alternatives when rooms differ

Sample review is also the moment to sanity-check the model choice itself. A two-piece body suits some budgets and layouts, a wall-hung unit frees the floor for cleaning in tight commercial WCs, and a suite approach keeps styling consistent across guest bathrooms. Reviewing samples side by side makes that decision visible rather than theoretical:

Model Form Drainage as listed Where it usually fits
Washdown One Piece Toilet 1004A One-piece, square-rounded minimalist profile P-trap wall drain and S-trap floor drain options Villas, hotels and residential upgrades where the one-piece look and easy cleaning are specified
Two Piece Washdown Toilet 1038A Two-piece body, smooth glazed surface Dual S-trap and P-trap options as listed Apartments, hotels and commercial restrooms in volume fit-outs
Wall Hung Toilet 1038W Wall-mounted with concealed tank, floor left clear P-trap wall drainage as listed Contemporary bathrooms and compact WCs where floor cleaning and visual lightness matter
Washdown One Piece Toilet 1051A One-piece, softer rounded profile; part of a coordinated 1051 suite P-trap and S-trap options as listed Projects standardising one look across guest bathrooms and matching basins

Trap types and rough-in figures in that table are the values published on each product page. Treat them as the starting point for measurement, and confirm the number for your batch against the technical sheet before the sample is signed off.

Step 6 — Put the approval in writing

Once the sample passes, record it. A short approval note prevents disputes later and gives your site team something to check incoming cartons against:

  • Photograph the approved sample with a scale and the model marking visible; keep it on file as the reference piece.
  • State the glaze colour and gloss, seat finish, trap type and rough-in dimension you have accepted, along with the data sheet version.
  • Note the packing standard for the production order — carton marking, protective corner protection, and how many units per room floor are shipped together.
  • Agree what happens if a delivered batch deviates from the approved sample, before production starts rather than at handover.

How we support this stage

SANTERSON works as a China-based manufacturer and one-stop supplier for furniture and building materials, supplying bathroom ceramics alongside the fixtures, lighting, cabinetry and finishes that surround them on the same project. Our stated cooperation steps run from project brief and design proposal through quotation and detail confirmation to production, shipment and follow-up, with custom and OEM service available where a project needs bespoke finishes or branding. For a ceramic order that means the sample stage is treated as part of the project workflow: specification confirmed, sample reviewed against your drawings, then production scheduled.

Send us the room layout, the drainage set-out and the finish palette you are working to, and we will return the matching 1004A sample with the technical data sheet for that batch so your team can complete the checks above on site.

View Washdown One Piece Toilet 1004A in the catalogue, or contact our project team to arrange a finish sample for review before your production run is scheduled.