A flexible wood grain cement wall panel looks like timber cladding, bends like a sheet of heavy paper and is made from a cement-based mineral compound. That combination is exactly why it works so well on arches, columns and curved feature walls where rigid boards have to be kerfed, steam-bent or abandoned. It is also why the product is easy to specify badly. The surface pattern, the bend radius, the paint system and the fixing method all have to agree before the first sheet leaves the factory, otherwise the panels arrive on site and the installer discovers the mismatch.

The checklist below covers what we ask every project buyer to confirm before production of our flexible wood grain cement wall panel starts. It is the same list our production team works from, so if you can answer these points, your enquiry moves straight to quotation and sampling instead of another round of emails.

1. Where the panel is going: interior wall, facade or renovation overlay

The material itself is described as water and moisture resistant and non-combustible, which is why it appears on both interior feature walls and exterior facade cladding. What changes between those two settings is not the sheet but everything behind it: the substrate preparation, the adhesive selection, the joint detailing and how water is allowed to leave the wall build-up. Tell us whether the panel is being applied to a new build or bonded over an existing surface during a renovation, because an old render or painted masonry wall usually needs its own assessment before any cladding is specified.

2. The actual bend you need, not just "curved"

"Curved wall" covers anything from a gentle 1200 mm radius reception desk wrap to a tight column or arch soffit. Send us the radius, the direction of the curve and whether the panel wraps a convex or concave surface. Where the geometry is unusual, we produce a sample bent to your radius before the order runs, so you can see how the wood grain pattern distorts across the bend rather than judging it from a flat photograph.

3. Which wood grain, and how the boards meet

Wood grain panels only look convincing when the grain direction, board width and joint treatment are decided in advance. Confirm the grain pattern and board format you want, whether joints should be tight or shadow-gap, and where the panel starts and stops. A running bond versus a stacked layout changes both the cutting plan and the waste figure, so it is cheaper to settle on a drawing than to rearrange boards on site.

4. Colour: accept the white raw surface or lock in a finish

The panel is supplied with a white raw surface that can be painted, which gives buyers freedom to match a joinery tone or a brand colour on site. That freedom needs a decision before production: state whether you want the raw paintable surface or a pre-finished colour, and if pre-finished, supply a physical sample or a named colour reference rather than a screen value. Paint systems behave differently indoors and in direct sun, so the exposure condition belongs in the same conversation.

5. Substrate and fixing method

Flexible mineral panels are thin enough to follow a curve but still need a sound, flat and structurally adequate base. Confirm what the panel is being bonded or fixed to — cementitious board, gypsum board, existing masonry, a framed substrate — and who on site is responsible for preparing it. We work with tile-adhesive fixing and simple on-site cutting, drilling and bending with standard tools, but the load path, the edge restraint at openings and any movement joint remain your local engineer's or contractor's call.

6. Quantities, lengths and how the order ships

Because these sheets can be rolled rather than packed as rigid slabs, packaging and freight are part of the specification, not an afterthought. Confirm the panel area per elevation, the roll length that suits your site access, and whether you want spare sheets in the same production batch. Panels from different dye lots can read differently once installed side by side, so a single batch for a single wall is worth arranging up front.

7. Who signs off the sample

Before mass production, name one person on your side who approves the sample and the approved finish. Then hold that sample on site as the reference during installation. Most disputes about decorative cladding are really disputes about which reference governs — the photograph in the catalogue, the digital render or the sheet the installer is holding.

One thing we deliberately do not promise in writing: local code compliance. Fire performance and building-product requirements differ by country and by state, and a product description that calls a material non-combustible is not a certificate for your jurisdiction. If your project needs documented testing or a specific classification, raise it at quotation stage so we can confirm what documentation exists for the exact panel you are buying.

How this fits with our other flexible wall cladding

Some projects mix finishes on one elevation — a wood grain wrap at reception, a stone or earth-toned surface behind the bar. Our flexible rock stone panel reproduces a rugged natural stone face and is similarly rolled for shipping and applied to curved surfaces, while the MCM flexible rammed earth panel brings a softer, earthy texture that bonds directly to cement board or gypsum with tile adhesive. When two or three of these systems appear on the same wall, decide the transition detail before production so the different thicknesses and joint profiles meet cleanly.

All three are part of our wider wall panels and wall cladding range, alongside decorative and acoustic panelling for hospitality, villa and commercial interiors.

Frequently asked questions

Can the panel be cut on site?

Yes. Cutting, drilling and bending are done with simple hand tools on site, which is how installers fit around sockets, reveals and services without returning sheets to the factory.

Can I paint it a custom colour myself?

Yes. The white raw surface is designed to take paint, so a contractor can match the panel to a scheme on site. Tell us if you intend to do this, because it affects whether we ship the sheet raw or pre-finished.

Is it suitable for exterior use?

The product is used for exterior facade cladding and is water and moisture resistant. Fixing details, substrate preparation and any local documentation requirements still need to be settled for the specific building.

If you can send the elevation drawing, the curve radius, the panel area and your colour intention, we can quote and arrange a sample against your actual detail rather than a generic one. Use our contact page to reach the project team.