A wall hung bidet rarely appears on a project bill of quantities until the design intent is fixed: floating bowl, concealed supply and waste, matching suite. Then the buyer has to decide whether to order the catalogue item as published or have it produced under their own brand and specification. This article walks through how OEM sourcing works for our Wall Hung Bidet 1004F, Modern Ceramic Wall Mount Bidet for Bathroom, from the first drawing exchange to a container that arrives with the paperwork your customs broker expects.
What OEM Means Here, and Where It Differs From Private Labelling
In our Custom & OEM Service, two very different requests often arrive under the same word. The first is private labelling: you take an existing mould, keep the geometry as it is, and put your brand on the underside of the bowl, plus your carton and insert. The second is genuine OEM: your engineering team supplies the mounting interface, the trap orientation and the finish schedule, and we produce to that document set against our ceramic body.
The 1004F sits comfortably in both categories. It is a vitreous ceramic bowl with a smooth glossy glaze, fixed to the wall through its back panel, with a rounded square outline rather than sharp corners. Because the visible form is simple and the fixing principle is standard, most OEM changes on this item are about surfaces, branding and how it is packed — not about re-engineering the casting. That is what keeps an OEM order on this type lead times close to a standard replenishment order.
Step 1: Confirm the Interface Before You Talk About Price
The most expensive mistake in ceramic OEM sourcing is negotiating unit price before the technical interface is agreed. For a wall hung bidet, three items decide whether the bowl can be installed on your wall at all:
- Trap and rough-in arrangement. Whether the waste exits through the wall or the floor, and where that outlet sits relative to finished floor and finished wall. Our published product record lists the 1004F at 545×360×410 mm overall; the trap position and rough-in are not settled by that number and must come from the technical sheet for the production batch.
- Carrier frame or direct fixing. The 1004F is described as wall-mounted and fixed with a back panel. Confirm which carrier system your project uses, and confirm the bowl's hanging points match it before any mould work is discussed.
- Tapware deck and inlet position. Where the faucet holes or inlets sit changes the drilling pattern, and drilling after glazing is not an option. Send your tapware datasheet with the enquiry, not after the quotation is issued.
Send us these three points on a marked-up drawing and we can quote against something real. A quotation built on a photograph alone is a quotation that will be revised.
Step 2: Decide What You Actually Want Changed
Our Custom & OEM page covers bespoke material finishes and textures, custom design and prototyping, flexible minimum order quantities, and brand customisation including private labelling. Applied to a ceramic wall hung bidet, that breaks down into a short, practical list:
| Change | What it affects | Typical order impact |
|---|---|---|
| Glaze colour and sheen | Slip fit, firing schedule, colour match against your sample standard | Requires a pre-production glazed sample for approval |
| Brand marking on the underside of the bowl | Mould marking or post-firing marking, position and legibility | Low cost once artwork is final |
| Carton, insert and pallet pattern | Retail readiness, breakage rate, container loading plan | Printed packaging has its own lead time; plan it early |
| Included hardware and inlet set | What the installer opens on site | Bundle only what your installers actually use |
| Suite pairing with other ceramics | Visual consistency across the bathroom | Order the suite together so glaze batches match |
That last line matters more than buyers expect. A bidet ordered in one batch and a basin ordered much later can read as two different whites on the same wall. Where the schedule calls for a matched suite, group the Wall Hung Bidet 1004F with the Wall Hung Ceramic Basin 1051B and the Wall Hung Toilet 1051W: the 1051 range is documented as a coordinated set sharing the same soft rounded profile, so placing those lines on one purchase order keeps the glaze batch consistent across the room.
Step 3: Approve a Physical Sample, Not a Render
For OEM ceramic work we go through modelling and prototyping before production tooling is committed. For your file, insist on three approvals in this order:
- Glazed tile or glazed offcut in the exact finish, viewed in both warm and cool site lighting.
- One full sample bowl with your branding and packaging mock-up, which you then mount on a mock-up wall with your own carrier frame and tapware. This is where interface problems surface cheaply.
- A signed pre-production sample retained by both sides as the acceptance reference for the batch.
Keep that signed sample. When a full container load lands in a warehouse and someone questions a sheen difference, the sample settles the argument; an email thread does not.
Step 4: Quantities, Batch Planning and Mixed Containers
Flexible minimum order quantities are part of how we work, but ceramics are still fired in batches and glazed in runs. Two planning rules keep an OEM order predictable:
- Order the custom finish in one run. Splitting a bespoke glaze across two orders far apart invites visible variation between halves of the same hotel floor.
- Consolidate with the rest of the fit-out. Bathroom ceramics travel well alongside Bathroom Sanitary Fixtures, shower sets, vanity cabinetry and wall finishes. One consolidated shipment means one set of customs documents and one delivery window for the site team.
If you are phasing a project, tell us the phasing at quotation stage. We can then split production runs inside one agreed specification instead of reopening the tooling conversation each phase.
Step 5: Packing, Freight and Documents
Wall hung ceramics are unforgiving of weak packaging. The bowl carries load on its hanging points, not on the rim, so the carton has to hold the body in a way that keeps point loads off the glazed faces. Our Logistics & Door-to-Door Delivery service covers freight forwarding by sea, air and rail, packaging and container loading, customs paperwork including commercial invoices, packing lists and certificates of origin, shipment tracking and door-to-door delivery.
For an OEM order, agree the packing specification in writing before production: carton grade, corner protection, inner dimensions, pieces per carton, gross weight, and the pallet or loose-loading pattern. Those numbers also feed your own storage plan, because a warehouse that cannot stack the carton safely will produce damage that is charged to nobody.
Ask for the packing list in the format your broker needs, and confirm import requirements for the destination country case by case with them rather than assuming a template from another shipment.
Step 6: Site Handover and After-Sales
Ceramic claims are almost always installation claims. Before the bowls reach site, circulate one page to the installing contractor: carrier frame used, fixing torque sequence, waste connection method, protection during grouting, and the point at which the protective film comes off. Our Installation & After-sales Support covers on-site installation support, inspection and snag lists, warranty handling, spare parts and replacement, and ongoing maintenance.
Two practical habits protect an OEM order after delivery. First, keep a small buffer of spare bowls from the same glaze run in country; replacing a damaged unit long after handover with a bowl from a different run is how a matched suite stops matching. Second, photograph the installed unit and its marking at handover, so any later claim identifies your branded batch rather than a generic catalogue item.
A Short Checklist for Your Next Enquiry
Send these six items and an OEM quotation on this type comes back accurate rather than provisional:
- Reference to the model — here, Wall Hung Bidet 1004F — with your project name and destination port.
- Rough-in drawing: waste direction, outlet height and offset from finished wall and finished floor.
- Your carrier frame specification and tapware datasheet.
- Glaze finish reference, plus the branding artwork position.
- Packaging requirement: retail carton, project carton, or bulk palletised.
- Total quantity with the phasing plan, and whether the bidet is ordered as part of a matched suite.
As a China-based furniture and building materials manufacturer, we handle these bathroom ceramic orders inside the same project programme as cabinetry, wall and ceiling finishes, lighting and loose furniture, which is where OEM sourcing starts to pay for itself: one specification owner, one consolidated shipment, one point of accountability from drawing to handover.
Working on a bathroom fit-out and want the 1004F produced under your own brand? Send the rough-in drawing and finish reference through our contact page, and we will confirm what can be tooled, glazed and packed to your specification.