A swim spa is easy to specify on paper and difficult to place on site. The Outdoor Swim Spa WS-PC07ST sits in the middle of our configurable outdoor swim and hydrotherapy range, and project teams keep asking the same practical question: where does this unit actually work in a hotel or a villa? This article answers it room by room and site by site — which settings suit a shell of roughly seven metres long, two and a half metres wide and about one and a half metres deep, what has to be settled before the unit ships, and how the swim spa ties into the rest of the package we supply as a one-stop furniture and building materials supplier.

The short answer: WS-PC07ST fits where you have a clear rectangular footprint about 7.5 m long by 3 m wide with room for circulation, an approach that carries the unit to its final position, and a decision made early about whether it sits at deck level, partly recessed or on a raised platform. That covers podium terraces, resort garden lawns, villa rear decks, rooftop plant-adjacent decks, wellness extensions and staff-fitness areas — but not narrow inner-city townhouse sites, upper floors without a structural review, or any location where local approvals and electrical rules have not yet been checked.

What WS-PC07ST is, before you decide where it goes

WS-PC07ST is one of the longer swim configurations in our range. The catalog lists it at 7000 × 2400 × 1470 mm, with a control system, a swim training system, a filter pump, six water jets, four LED lights and a total power figure of 6.55 kW. Ozone is listed among the features shown on the product page.

Read those numbers as design inputs rather than guarantees. The catalog entry for this model does not state a water pump quantity, so the pump set has to be confirmed with us for the configuration you actually order — along with electrical requirements and which options are included. Catalog-listed options across the range include control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps, and availability varies by model.

Two sibling configurations help when a site is awkward. WS-PC07ST-L runs 7490 × 2400 × 1470 mm — the extra length usually buys a longer swim lane or a deeper seat zone. WS-PC07ST-S keeps the 7000 mm shell and adds an automatic cover option, which matters on exposed decks where debris, evaporation and safety come into play. If your site is shorter than expected, WS-PC06ST at 5900 × 2400 × 1470 mm and WS-PC05ST at 5000 × 2400 × 1470 mm are the usual fallbacks in the same family. If you want a wider water surface rather than a longer one, WS-PC07A at 7000 × 3000 × 1470 mm carries a substantially larger jet count and is closer to a spa-first layout.

Where it works in hotel projects

Podium terraces and rooftop wellness decks

On city hotels, the swim spa usually goes on a podium or roof level where a full pool is impossible — too much water, too much structure, too many approvals. A single self-contained shell with a defined footprint is easier to coordinate than a constructed pool, and it can be craned or walked in during the fit-out phase rather than built in situ. Straight edges make it simple to line up with paving joints and glass balustrade lines.

Two things decide whether this works: structural sign-off for a water-loaded vessel on a slab, and a route from the loading dock or lift to the terrace that clears the shell's width and height. Settle both before you fix the deck level.

Resort garden lawns and pool-deck extensions

For resorts, a swim spa next to the main pool adds an adult lap-and-recovery zone without competing with family swimming. It also extends usable hours: heated water plus four LED lights means the unit earns revenue in shoulder season and after dark, which a large unheated pool does not.

Position it so guests can be supervised from the pool bar or lifeguard point, and keep service access behind the plant rather than through a guest path. We supply the surrounding outdoor furniture to match — cabana daybeds for privacy, sling loungers for high-turnover deck seating, and pergolas or hardtop gazebos for shade.

Guest-room wings and villa-style suites

Boutique hotels and serviced-apartment operators increasingly put a swim spa on a private terrace belonging to a signature suite. One unit differentiates the top of the rate card without building a second pool. The trade-offs are privacy screening, noise from pumps in quiet zones, and a clear maintenance route that does not cross guest space.

Spa, wellness and staff fitness areas

For spas, a swim spa with jets and a current is a compact hydrotherapy and contrast-circuit asset — recovery treatments, aqua classes, warm-water programming. Back-of-house is the underrated use: staff fitness and recovery facilities in larger resorts are increasingly specified, and one unit serves a whole roster without the footprint of a pool plant room.

Where it works in villa projects

Rear decks and long narrow blocks

On suburban villa sites, the swim spa's length-to-width ratio is the reason owners choose it. A seven-by-two-and-a-half-metre shell fits along a narrow rear boundary where a pool would leave no lawn at all. Aligning it with the house axis keeps views from the living room clean and leaves side access for maintenance.

Terraces, rooftops and penthouses

Multi-level villas and penthouses use swim spas on terraces where an in-ground pool is out of the question. Same rule as hotels: structural review first, then an installation route — crane over a boundary wall is common when side access is blocked.

Courtyards, atria and indoor-outdoor rooms

A glazed courtyard or an atrium room that opens to the garden can host a swim spa year-round. This is where the automatic cover option on WS-PC07ST-S pays for itself, and where humidity control and ventilation need to be designed with the interior fit-out rather than bolted on later.

Basements and plant rooms

Below-grade installations work when ceiling height, drainage, access and dehumidification are resolved early. The unit itself is not the hard part; the room around it is. We will confirm equipment and electrical requirements for the chosen configuration, but ventilation design and waterproofing belong with your engineer and architect.

Site conditions to settle before you order

ItemWhat to decide
Footprint and clearancesAllow working space beyond the 7000 × 2400 mm shell for access panels, steps, seating and cleaning. Confirm finished levels before paving is set out.
Installation routeGate widths, turning circles, overhead obstruction, crane reach, lift size. The delivery path must clear the shell's dimensions on the day.
Support and structureA level, adequately bearing base for a full water load; on slabs and terraces, structural sign-off from your engineer.
PowerThe catalog lists 6.55 kW total power for this configuration. Supply sizing, protection and earthing are confirmed with your electrician against local requirements.
Drainage and overflowWhere first-drain and any overflow discharge to; graded surfaces away from the shell.
Equipment optionsHeat pump, UV sterilization, sand filtration, insulation, steps, water pumps — confirm what is included for your configuration before order.
ApprovalsLocal building, fencing/barrier and plumbing requirements are the project's responsibility. We do not warrant compliance with any specific national or state code.

Specifications quoted here are transcribed from the catalog page for this model. Confirm included equipment, pump set and electrical requirements against your selected configuration before ordering.

Designing the surrounding space as one package

A swim spa looks cheap or expensive depending on what sits around it. Because we manufacture both the water feature and the finishes, one procurement covers the whole zone:

How procurement runs on a real project

Through our turnkey solutions, a swim spa moves through the same six stages as the rest of the package: consultation, design and planning, production, logistics, installation and after-sales. Under interior design services we plan space layout, produce concept schemes and 3D renderings, and coordinate drawings and production so the spa shell, its base, its power and the surrounding furniture are drawn against one set of dimensions instead of four separate suppliers'.

Where a project needs non-standard dimensions, finishes or branding, our custom and OEM service covers bespoke material and finish selection, prototyping and private labelling. Freight is arranged by sea, air or rail with packaging and container loading, customs paperwork and door-to-door delivery under our logistics service; import terms, duties and transit times are quoted per project rather than assumed. After handover, on-site installation support, inspection with snag lists, warranty coverage, spare parts and maintenance sit under our installation and after-sales service.

Our published project references include villas in Sydney, Melbourne, Willoughby, Perth and North Turramurra; scope details for each case are on the individual project page. For a full product list, browse swimming pools and swim spas or talk to us as your furniture supplier for Australian projects.

Checklist before you commit

  • Confirmed finished deck level, base build-up and structural sign-off for a water-loaded vessel.
  • A verified delivery route from kerb or loading dock to final position, including crane or lift arrangements.
  • Configuration signed off: heat pump, filtration, UV, insulation, steps and cover option as required.
  • Electrical supply sized against the listed total power and local requirements, with isolation positioned to code.
  • Barrier, fencing and access approvals confirmed with your local authority.
  • Surrounding furniture, paving, shade structures and wet-area fixtures drawn to the same dimensions.
  • Maintenance access, drain points and storage for chemicals agreed with the operator's team.

Frequently asked questions

Is WS-PC07ST the right length for a small villa block?

At 7000 × 2400 mm it needs roughly a 7.5 m by 3 m clear zone once circulation and access are added. If that is too tight, WS-PC06ST at 5900 mm or WS-PC05ST at 5000 mm in the same family free up the difference.

Can it be installed above ground level?

Yes — at deck level, partly recessed, or on a raised platform with steps. Each option changes the base build-up, access details and steps required, so decide before paving is set out.

What is included in the price?

The catalog lists control system, swim training system, filter pump, six jets, four LED lights and ozone for this configuration; a water pump quantity is not stated for this model. Confirm the exact equipment list and electrical requirements for your order.

Does it come with a cover?

The automatic cover option is listed on WS-PC07ST-S. Ask us which cover options apply to the configuration you are specifying.

Do you handle delivery and installation?

We arrange freight by sea, air or rail with customs paperwork and door-to-door delivery, then provide on-site installation support and after-sales service. Compliance approvals for the site remain the project's responsibility in each jurisdiction.

Send us the drawing, not just the model number

Share a site plan or terrace layout with levels and access notes. We will tell you whether WS-PC07ST fits as drawn, which sibling configuration suits better, and what the surrounding deck furniture, shade structure and wet-area fixtures would cost as one package.

SANTERSON — China-based manufacturer and one-stop supplier of furniture and building materials for hotel, villa and office projects, operating since 2008.

Contact: PHILLIP  |  Phone / WhatsApp: +86-13928214007  |  Email: santerson@qq.com

Factory: Longjiang, Shunde, Foshan 528318, China. Offices listed in China, Vietnam, Singapore and South Africa. Business hours Monday–Saturday, 8:00 AM–6:00 PM (GMT+8).