An outdoor swim spa has to earn its place on a villa site plan. It competes with the pool deck, the pergola, the outdoor lounge and the garden, and it carries plumbing, power and structural obligations that a sofa never will. That is exactly why Outdoor Swim Spa WS-PC01 sits in a useful middle band of our range: a compact shell that fits a narrow side yard or a terrace setback, with enough jet capacity to work as a daily hydrotherapy pool rather than a decorative feature. The notes below follow the way we actually specify these units on villa and resort projects, so you can take them straight into a drawing review.

Start with the footprint, not the styling

The catalogue dimension for WS-PC01 is 3000 × 1050 mm. Read that as a shell envelope, not as a finished installation. On site you need working clearance at the ends for access and cleaning, plus room for steps, planting, and whatever paving or decking edge you build around it. In practice we ask the design team to mark three lines on the plan: the shell outline, the maintenance access zone, and the position of the control unit. Missing the third line is the most common cause of a re-plan.

Basin depth changes how the spa is used day to day. A shallower basin suits casual soaking; a deeper one supports seated hydrotherapy and full-body immersion while seated. Before you fix the model, decide who uses the spa and at what hour of day, because that decision drives depth, seating layout and jet count far more than aesthetics do.

Read the specification as a system

The published WS-PC01 data lists one control system, two water pumps, one filter pump, 53 jets in total, one LED light and a total power figure of 6.65 kW, with water jets, LED lighting and ozone shown as the featured functions. Two things follow from reading those numbers together.

First, total power is an electrical design input, not marketing copy. It determines the circuit, the protection device and where the distribution board has to sit relative to the spa. We confirm the supply arrangement for the selected configuration with the client's electrician before production, because a specification agreed after the slab is poured is expensive to change.

Second, jet count only means something once you know the layout. Fifty-three jets in a three-metre shell are distributed across seating and reclining positions; what a buyer should ask for is a diagram showing which station each jet serves, so the massage zones line up with where people actually sit.

One honest caveat on our own catalogue: not every row of the table is filled in for every model. For WS-PC01 the swim training system is not listed in the published data, so if a project needs a counter-current swimming station, we treat that as an item to confirm or upgrade rather than something assumed from the model name. The same applies to included equipment and electrical requirements, which are confirmed per configuration.

Compare within the range before you commit

The nearest sibling is Outdoor Swim Spa WS-PC01A: same 3000 mm catalogue length, but a second dimension of 930 mm against 1050 mm, a jet total of 28 rather than 53, and 3.25 kW of total power instead of 6.65 kW. Two consequences follow. The electrical load drops noticeably, which lightens the circuit and distribution work. And with fewer jets spread over the same length, the massage coverage per seat is thinner — a reasonable trade for short evening soaks, less reasonable when hydrotherapy is the reason the spa is being bought.

If neither shape works, the wider Swimming Pools and Swim Spas category covers longer shells and spa-only formats. Buyers comparing three or four models side by side almost always narrow the choice on depth and pump arrangement rather than on appearance.

Options that change the running behaviour

The catalogue lists control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps as options. Their real effect is on how the spa behaves through a season:

  • Heat pump — shifts the running cost profile away from direct resistive heating; decide this before the plant room or cabinet position is drawn.
  • Insulation — matters most where the spa sits outdoors year-round, and it pairs with the heat pump decision rather than replacing it.
  • Ozone and UV sterilisation — reduce the chemical load needed to keep water clear in a small volume of water that is used frequently.
  • Sand filtration and filter pump sizing — determine how often cleaning cycles interrupt use; confirm the cycle plan with the supplier.
  • Steps — set the entry height, which then fixes paving levels around the shell.

Availability and compatibility of these options vary by model, so we issue a written configuration sheet for each project rather than leaving the list open until order placement.

Coordinate the spa with the rest of the outdoor package

A swim spa is never delivered alone on a villa job. Paving, decking, loungers, shade structures and storage for chemicals and towels all touch it. Ordering those from several suppliers separately is how level differences, clashing finishes and split delivery dates appear late in a programme. We handle the swim spa as one line inside a single package with outdoor furniture for villas and resorts, so the decking boards, the lounger weave and the coping are specified against the same drawings.

As a one-stop project furnishing supplier, we carry that package through design consultation and space planning, material selection and product specification, manufacturing and quality control, project management and site coordination, then installation and handover. For swim spas specifically, our part of the scope is the unit, its confirmed configuration, packing and delivery; the local contractor keeps the civil, electrical and plumbing works. Getting that boundary written down early prevents the classic gap where nobody owns the isolator or the drainage fall.

A short specification checklist

  • Confirm the shell envelope plus access clearance on the plan, and mark the control unit position.
  • Fix basin depth against the users and their routine before choosing the model.
  • Request a jet layout diagram, not just a jet count.
  • Confirm total power, supply arrangement and protection device with the site electrician.
  • State explicitly whether a swim training system is included, absent or an upgrade.
  • Agree heating, insulation and sterilisation options before production starts.
  • Set the delivery boundary: what we supply, what the local contractor installs.

Where the handover line sits

Send us the plan extract, the intended users and the target handover date, and we will come back with a configuration sheet for WS-PC01 or the model that actually suits the site — options priced in, so the number you approve is the number you build to.