A swim spa sits in an awkward place on a project schedule. Interior designers treat it as a piece of loose furniture, landscape architects treat it as hardscape, and the M&E consultant treats it as a small plant room full of pumps. Outdoor Swim Spa WS-SP600 is a configurable acrylic-shell swim and hydrotherapy unit, and units like it fall between all three disciplines. That is exactly where designers and buyers stop agreeing: the specification sheet is short, and the coordination around it is where projects lose time. Below is what we ask both sides to settle together before an order is placed.

Start with the footprint, not the finish

Designers and buyers tend to review a swim spa from opposite ends — one looks at the shell finish, the other at the price line. Begin with the geometry instead. The catalog lists WS-SP600 at 5900 × 2500 × 1600 mm. That number is the shell envelope, and it is the wrong number to design around on its own. Two drawings need to be produced before the spa appears on any layout:

  • Setting-out plan. The pad has to allow for the shell, a working gap at pump and control access points, insulation build-up where specified, and steps at the entry side. Steps change the plan more than most people expect — they push the usable deck line outward by roughly the tread depth plus a landing.
  • Deck interface line. Decide early whether the coping or pavers sit on the spa rim, on an independent perimeter beam, or on a full concrete surround. Each option reads differently and each behaves differently under movement. A flush surround with no movement provision is a frequent cause of cracked tiles once the shell and the slab move independently.

The 1600 mm depth is also a design decision, not just a dimension. It suits lap swimming and standing hydrotherapy; it is shallow for diving and deep for small children. Where the users include older guests or anyone with limited mobility, the entry arrangement matters more than the jet count.

Read the specification as a base configuration

Once the footprint is agreed, both sides need to agree on what the model name actually covers. The published figures for WS-SP600 are control system 1 set, swim training system 1 set, filter pump 1 pc, jet total 6 pcs, LED lights 4 and total power 9.35 kW. The water pump is left blank in the specification block on this product page. That gap should be closed in writing rather than assumed: units sold under one model name can reach site with different pump and jet arrangements depending on the option set that was quoted.

Compare it with WS-SP600-MS, which shares the 5900 × 2500 × 1600 mm shell but lists a water pump, 29 jets and 11.55 kW total power. Same footprint, same deck detail, materially different electrical load and jet performance. For a designer, that means the wet area layout can be frozen early while the equipment schedule stays open. For a buyer, it means any comparison between quotations has to state which configuration is priced.

ItemWS-SP600 (as listed)Confirm on the quotation
Shell dimensions5900 × 2500 × 1600 mmPad size, working clearance, step arrangement
Swim training system1 setType of flow, adjustable output, control location
Jet total6 pcsJet positions against seating and swim lane
Water pumpNot shown in this specification blockWhether included, capacity, which circuit it serves
Filter pump1 pcFiltration media and sand filtration if specified
LED lights4Recessed position, colour control, low-voltage supply
Total power9.35 kWSupply phase, dedicated circuit, protection device
Catalog-listed options for this range include control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model. Nothing on the product page should be read as a guarantee that a given option is available for a given shell — it has to be confirmed against the configuration being quoted.

The electrical conversation belongs in concept design

This is where designers and buyers most often fall out of step: the electrical item gets deferred on the design side and priced without checking on the procurement side. Total power of 9.35 kW for the listed WS-SP600 configuration, and 11.55 kW for the -MS variant, is not a figure an electrician can absorb late in a job. Add a heat pump and the load changes again. Three items should be closed out before tender documentation:

  • Single-phase or three-phase supply to the plant location, and whether the project's distribution board has spare capacity for a dedicated circuit with the correct protection.
  • Cable route from the board to the spa, including containment, and how it avoids the excavation zone for the pad.
  • Location of the control system and whether the owner wants wall-mounted or accessible-from-deck control. Retrofitting a controller position after the deck is laid is expensive and visible.

Local electrical requirements are set by the authority having jurisdiction on site, not by the manufacturer's data sheet. We supply the equipment load and connection requirements; your local consultant confirms compliance for the installation location.

Decide what the spa is actually for

The other place where designers and buyers drift apart is intended use, because the use decides which options matter. A swim spa specified as a fitness asset and one specified as a hospitality amenity are different products in practice, even with the same shell:

  • Daily training. The swim training system's flow quality and controllability matter more than jet count. Insulation and a heat pump move the running profile if the unit is used year-round rather than seasonally.
  • Hydrotherapy and recovery. Jet positions relative to seating are what people feel, so the same jet count in different places gives a different experience. Where a project needs a non-standard shell form, the customized shape outdoor spa option in our acrylic-shell range covers square, round, oval and curved configurations for gardens and terraces.
  • Guest-facing amenity. Water treatment becomes the operational concern. Ozone is shown as a standard feature on this model; UV sterilization and sand filtration are options. Housekeeping and maintenance access should be planned, not improvised.

What the buyer should put in the comparison sheet

Designers and buyers rarely read the same document, so the misalignment here is usually a missing line item rather than an open disagreement. When two quotations look identical on the surface, these are the lines that separate them:

Shell colour and acrylic finish Exact equipment list per circuit Insulation package and where it is applied Steps — included, optional or site-built Delivery term and delivery point Crane or plant needed to set the shell Site preparation scope: who pours the pad Commissioning and handover documentation Spares and warranty terms as written

Delivery is worth a note of its own. A shell of this size arrives by road freight and needs an agreed set-down point, plus lifting plant if the position is not accessible from the truck. That scope has to be assigned in the contract — otherwise it surfaces on delivery day with nobody booked for the lift. Our logistics and door-to-door delivery service covers freight forwarding, packaging and container loading through to the delivery point; site access arrangements and lifting remain a joint decision with the builder.

A short coordination sequence that works

Alignment is easier to run as a sequence than to recover after the fact. This order keeps the designer and the buyer working from the same sheet:

  • Concept. Fix intended use, depth acceptance, and whether the spa is freestanding or surrounded. select the shell size — WS-SP600, or WS-SP500 at 5000 × 2500 × 1600 mm for a tighter plot, or a customised shape if the layout calls for it.
  • Design development. Issue the pad and clearance drawing, agree the deck interface detail, confirm supply phase and control position with the M&E consultant.
  • Tender. Both designer and buyer sign off the same configuration sheet. Quote against that written configuration, not a model number alone, and record every option that is excluded.
  • Pre-install. Confirm the set-down point, lifting method, and that the pad, drainage and power are complete before the shell arrives.
  • Handover. Commission in front of the client's maintenance contact, hand over the equipment schedule as-built, and walk through water treatment and winter or low-use procedures.

If you are specifying WS-SP600 for a villa or hospitality project and want the configuration confirmed against your drawings before tender, send us the layout and the intended use. We will return the equipment schedule, clearances and electrical requirements for that exact build, so the designer's drawing and the buyer's quotation describe the same unit. The full swimming pools and swim spas range is on the site if you want to compare shell sizes first.