Stone and marble finish the wall or the surface that every guest, buyer or resident touches first. That is exactly why it is so easy to get wrong: two projects can specify the same look and end up with completely different results, because the panel that works in a villa bathroom may be the wrong answer on a curved hotel lobby column. The deciding factor is rarely taste. It is the project information you hand to the supplier before samples are cut.

Below are the details we ask for on every stone & marble panel enquiry, and what each one changes in the quotation, the production route and the installation sequence.

1. Where the panels are going: wet zone, dry zone or exterior wall

Location drives material selection before colour does. A panel fixed to a dry bedroom wall has very different demands from one behind a basin or on a facade exposed to rain and sun.

  • Bathrooms and wet areas. Splashing, cleaning agents and changing humidity affect joints, edge detailing and the substrate behind the panel. Our stone & marble surfaces for bathroom projects are specified together with the vanity, basin and countertop layout so the stone meets the fixtures cleanly instead of being trimmed on site.
  • Feature walls in living areas, lobbies and corridors. Here the visible joint pattern, panel width and how the wall meets skirting, doors and lighting take priority.
  • Curved walls, arches, columns and reception desks. Rigid slabs cannot wrap a radius. For these we work with flexible stone products such as MCM flexible travertine stone veneer, an ultra-thin, bendable sheet that follows curved and special-shaped surfaces.
  • Exterior facades and renovation overlays. Weather exposure, freeze-thaw cycles and the load the existing structure can carry all narrow the options. A bendable soft stone alternative such as flexible rock stone wall panel is a lightweight mineral sheet that cuts on site and reduces wall load compared with heavy natural stone.

2. Substrate, level and access — the detail most enquiries leave out

The wall behind the stone decides how the panels are fixed and how much preparatory work your team carries out. Tell us what the substrate is (cement render, brick, gypsum board, existing tile or an old facade), whether it is plumb, and whether the site allows cutting and dust.

Flexible stone sheets bond to a cement base or gypsum board with tile adhesive and can be cut, drilled and bent on site with simple tools, which keeps joint treatment and working time under control. Heavy rigid slabs need structural checks, mechanical fixing and lifting arrangements. If the project is a renovation in an operating hotel or occupied villa, that difference alone often decides the specification.

3. Dimensions: measured openings, not drawn averages

Send measured dimensions for every wall, including the position of outlets, switches, mirrors, shower glass, door reveals and any reveal or shadow gap you want kept. Panels are made to measure, so a drawing that shows nominal sizes rather than finished dimensions produces panels that arrive needing on-site trimming — the fastest way to lose a clean stone joint.

For panelled systems that run floor to ceiling or wrap around doors and niches, we coordinate the panel layout with wall panel systems and integrated joinery so reveals line up across trades.

4. Finish, veining direction and sample approval

Stone is not a flat colour code. Specify the surface you want — polished, honed, matte, split-face or a replicated natural texture — plus the veining direction and whether book-matched or continuous patterns are required across a run. Then approve a physical sample against the approved finish before production starts. Colour and texture on a screen are not an acceptable basis for a stone order.

Where the design calls for a rammed-earth or rock-face look rather than polished marble, flexible panels reproduce that rough texture in earth browns and light tones, with custom surface painting available on request.

5. Quantities, phasing and container planning

Give us the total square metres, the number of rooms or floors involved, and whether the panels must arrive in phases. Cut-to-size panels for a 40-key bathroom package and a single villa feature wall are produced and packed very differently. Phased deliveries keep a site from storing stone in the wrong place, and panel sets grouped by room make installation far quicker for your crew.

6. How the panels meet lighting, joinery and other trades

Stone walls rarely stay alone. Backlighting, concealed doors, niches, mirrors and integrated cabinetry all need openings cut at the factory rather than on site. Where a feature wall carries lighting, we coordinate it with backlit feature walls and integrated lighting so electrical ratings, driver access and heat dissipation are settled before the panel is cut.

A quick comparison of the usual routes

Project detail What to send us What it changes
Location and exposure Room type, wet or dry, interior or exterior, climate Material family, fixing method, edge detailing
Geometry Flat, curved, arched, column, ceiling reveal Rigid slab or flexible sheet; moulding or on-site bending
Substrate condition Base material, plumbness, load capacity, new build or renovation Adhesive or mechanical fixing; preparation scope on site
Dimensions Measured wall sizes, openings, services locations Panel cut list, joint layout, factory-cut openings
Finish Surface treatment, veining, sample approval Production route, lead time, approved reference for QC
Quantity and phasing Square metres, rooms, delivery sequence Packing, container loading, shipment plan

What a complete enquiry looks like

Before we quote, we normally want:

  • Drawings plus measured dimensions for each wall or surface
  • A note on substrate and whether the building is new build or renovation
  • The finish reference, or a sample you want matched
  • Locations of lighting, mirrors, doors and services that must be cut into the stone
  • Total area and required delivery sequence per floor or room
  • Destination port or site address for freight planning
A practical rule: if a detail would force your installers to cut stone on the finished floor, it belongs in the drawing package and the factory cut list instead. Every dimension, opening and joint we settle before production removes one decision from site.

Working with one supplier across the whole envelope

Stone panels sit inside a larger fit-out that also includes cabinetry, basins, vanities, lighting and flooring. Coordinating those items through one manufacturer keeps finishes, levels and joint details consistent from room to room, and it puts a single production schedule behind the whole package. As a hospitality furniture and building materials supplier, we handle custom sizing, material selection, production, packing and door-to-door delivery for villa, hotel and office projects, then support installation and after-sales follow-up.

If you have a stone or marble wall, countertop or cladding package on the boards, send the drawings and measured dimensions and we will come back with a material recommendation, panel cut list and quotation for that configuration.

SANTERSON — China-based manufacturer of furniture and building materials for villa, hospitality and office projects. Enquiries: PHILLIP, +86-13928214007 (phone/WhatsApp), santerson@qq.com.