A wall-hung basin looks simple on a drawing. It is one bowl, floating above the tile, with no cabinet underneath and nothing visible holding it up. That simplicity is exactly why the specification conversation decides whether the finished bathroom reads as clean and resolved, or as a compromise nobody planned for.
If you are sourcing Wall Hung Ceramic Basin 1051B for a villa, apartment or hotel bathroom — whether as the standard fixture across many rooms or as a customised version of it — what you hand the manufacturer matters more than the catalogue page. Below is the brief we would want to receive, and what each item changes on our side of the table.
Start With What the Standard 1051B Already Gives You
Before asking for changes, it helps to be clear about the baseline. The 1051B is a wall-mounted ceramic basin fixed to the wall through a back panel, so no vanity unit or pedestal is required and the floor beneath stays clear for cleaning. Its overall envelope is 400 × 380 × 450 mm, with a curved, minimalist outline that reads soft rather than angular.
The body is vitreous ceramic with a dense glossy glaze, chosen because it resists water marking and limescale build-up — the two things that make a white basin look tired in a heavily used bathroom. A single tap hole is reserved for a lone faucet, which keeps the deck clean but also means the faucet choice is part of the design decision, not an afterthought.
The 1051B sits inside a matching 1051 sanitary family, so where a project needs visual consistency across a floor or a guest-room type, the other pieces in that range can be specified to the same design language rather than mixed from three different collections.
The Six Things to Put in Writing Before Production
1. Trap type and waste position
This is the item that causes the most rework when it arrives late. Tell us whether the waste runs into the wall or down through the floor, and give the rough-in dimension from the finished wall to the centre of the waste. If your drawings show both options in different bathrooms — which happens often on renovation work where existing pipework survives a fit-out — say so explicitly and we will treat them as separate line items rather than one shared specification.
2. The faucet, and how far it reaches
With one tap hole reserved, the faucet has to be decided alongside the basin. Send us the model or a dimensioned sketch: spout reach, spout height above the deck, and whether the lever sits forward or to the side. A long-reach spout on a shallow bowl splashes; a short spout on a deep one leaves no usable space at the front. We check that pairing before tooling, not after.
3. The finished wall line
A wall-hung basin is dimensioned from the finished face of the wall, not from the stud. Tell us what is going on that wall — tile thickness, stone cladding, a tanking layer in a wet area — and where the tiling stop line falls relative to the back panel. This determines how the basin meets the surface and whether the back panel needs adjustment for your build-up.
4. Quantity per room type, not just total quantity
"Forty basins" is not a specification. "Twelve for guest bathrooms of type A, twenty-two for ensuite of type B, six for the spa level" tells us where consistency matters and where a variation is acceptable. Repeat-room projects are where a single agreed sample saves the most money, because one approval covers dozens of rooms.
5. Glaze colour and surface, if you want to move off white
White is the default for good reason: it shows residue least on a glossy surface and coordinates with any tapware finish. If a project calls for a different glaze tone or a non-glossy surface, flag it early and tell us the environment it lives in. A matte or textured surface in a high-touch guest bathroom behaves differently under daily cleaning than it does in a showroom sample, and we would rather discuss that trade-off at quotation stage than defend it after handover.
6. Matching the rest of the 1051 suite
Where the basin must sit alongside other fixtures from the same family — a wall-mounted WC, or a floor-standing basin in a powder room where a wall fix isn't possible — send us the full fixture schedule for that room type. We can then keep the outline, glaze and hardware consistent across the set instead of matching by eye at site level.
What a Custom Brief Unlocks on Our Side
SANTERSON works as a manufacturer for project buyers, not as a reseller passing drawings along. That means the brief above goes to people who can act on it: material and finish selection, prototyping before a run is committed, and flexible order quantities so a single room type doesn't have to be bought in bulk just to get a variation made.
For projects where bathroom ceramics are one line among many, the same coordination extends across the fit-out. The Custom & OEM Service covers bespoke finishes and private branding, while Logistics & Door-to-Door Delivery handles freight, customs paperwork and container loading, and Installation & After-sales Support covers site inspection, snag lists and replacement parts. Buyers running villa or hospitality work in Australia can hold all of that with one supplier instead of reconciling a ceramic vendor against a joinery vendor against a freight forwarder.
One honest note on scope: we are a China-based manufacturer with offices listed in China, Vietnam, Singapore and South Africa. We do not claim an Australian office or local code certification, and we will not tell you a product meets a standard we haven't been asked to test against. If your project has a compliance schedule, send it with the enquiry and we will work from the document rather than from assumption.
Where the 1051B Makes Sense — and Where It Doesn't
A wall-hung basin earns its place when floor area is tight and clean lines matter. In compact bathrooms, apartments, boutique hotel rooms and villa renovation work, keeping the floor clear under the sink changes how large the room feels and makes mopping a single wipe instead of a negotiation around a pedestal.
It is a weaker choice when the wall can't carry the load. Wall-hung fixtures need solid fixing into the structure behind the finished surface — a properly framed or engineered partition, not a thin board with nothing behind it. If your scheme puts a basin on a lightweight divider, tell us at enquiry stage; that's a structural conversation to have before anything is ordered.
It's also worth questioning in rooms where counter space is genuinely needed. A wall-hung bowl gives you a deck for soap and nothing more. If guests need room to set down toiletries, a vanity-mounted basin may serve the room better, and we would rather raise that than sell you the wrong fixture.
Questions Buyers Ask Us Most
Can I order one 1051B as a sample before committing to a room type?
Yes, and we recommend it. A single approved sample fixes glaze tone, faucet pairing and the wall build-up for every room that follows. Order quantities on custom work are set per project rather than at a fixed bulk minimum.
The dimensions are 400 × 380 × 450 mm — is that width, projection and height?
Those are the overall envelope figures published on the product page. We treat them as the starting point for coordination and confirm them against the current technical data sheet before your rough-in is fixed on site, because wall build-up and waste routing change what you actually need to allow.
We're furnishing a whole villa, not just bathrooms. Does one supplier make sense?
For villa and hospitality projects it usually does, which is why the range spans ceramics, cabinetry, lighting, flooring, wall finishes and outdoor furniture under one procurement line. The Interior Fixtures category covers the bathroom and kitchen elements that have to be coordinated with each other.
What do you need from our architect or designer?
A fixture schedule per room type, the plumbing layout showing waste and supply positions, and the wall build-up detail. If those three exist in any form — even marked-up drawings rather than issued documents — we can work from them.
Send the Brief Before the Drawings Are Final
The most expensive moment in a sanitaryware order is after the wall is closed up. Trap position, rough-in, faucet reach and wall build-up are all cheap to change on paper and costly to change in tile and silicone. Bring us the brief while it's still editable.
If you're specifying Wall Hung Ceramic Basin 1051B for a project — standard or customised — send the room schedule and plumbing layout, and we'll come back with a specification we can both hold to in production.
Talk to us through the contact page, quoting your room types and quantities. We'll confirm what's standard, what needs tooling, and what it costs — before anything is committed.