A floor-to-ceiling modular wall rarely fails because of the unit itself. It fails at the edges: where it meets the flooring, the ceiling line, the lighting circuit and the cabinetry beside it. When Santerson Floor to Ceiling Modular Systems are specified as part of one fit-out package instead of ordered in isolation, those junctions get settled once, in the same workshop, rather than argued out on site. The notes below follow the coordination order we use on villa and hospitality projects.
Start with the wall build-up, not the shelf layout
Modular systems are made to measure, so their final dimensions depend on what they sit against. Before any layout is drawn, confirm three things with the fit-out team: the finished floor level, the ceiling construction and whether the wall behind the system carries load or is a partition lining. A run that terminates into a plasterboard lining behaves differently from one framed into a solid wall, and the fixings differ accordingly.
The same question decides which collection to specify. Santerson Floor to Ceiling Systems sits in the modular shelving range and is configured around open storage for a residential wall. Where the brief calls for living-room joinery with doors, drawers and display niches, the modular living range (Santerson Mixed Open & Closed Systems or Santerson Closed Modular Units) is usually the better starting point. Both are specified by layout, dimensions and finish, so choose on storage behaviour first and appearance second.
Match finishes across cabinetry, panelling and flooring together
The most common coordination mistake is treating the modular wall as furniture and everything else in the room as architecture. Veneer, lacquer and laminate are matched by sample, not by name. A veneer panel ordered from one batch against a cabinetry door ordered from another will read as two different browns under warm lighting.
Pull the samples into one set before anything is released: the modular system carcass and door fronts, any Wood Veneer Panels or Santerson Acoustic Panels on adjacent walls, the engineered wood flooring running beneath the unit, and the kitchen or wardrobe cabinetry that sits on the same sightline. Where a modular run returns into a kitchen wall, matching the cabinet front specification to the modular door specification removes the need for a trim detail altogether.
Flooring sets the bottom of the elevation. Plank width, board thickness and the expansion gap at the perimeter all change the height the modular unit has to be built to, so fix the flooring selection before the modular dimensions go to production, not after the units arrive.
Resolve lighting and services before production
Integrated lighting is the item most often added too late. Where shelf lighting is wanted, specify it as part of the system. Santerson Integrated Lighting Systems and Santerson Modular System with Lighting (Living System) are configured together with the layout, so cable routes, driver positions and switching are planned into the panels rather than chased in afterwards.
Two details need closing before the drawings go to the workshop: where the driver sits and how it is reached for maintenance, and what switch or control the client expects. A display niche lit by a strip that cannot be serviced without taking a shelf off will come back as a snag. Where media equipment is involved, Santerson Integrated LED Media Units follow the same logic: power, signal and ventilation are settled at specification stage.
Confirm the electrical specification for the destination market with the local contractor. We supply the system and its lighting components to the agreed configuration; the on-site circuit, isolators and compliance sign-off stay with the project's electrician.
Coordinate doors, openings and sightlines
A modular wall that reads as architecture usually continues into the openings around it. Where a concealed door sits in the same plane, Santerson Decorative Concealed Doors or Santerson Flush Interior Doors can be taken in the same finish and panel layout, so the door line disappears into the joinery. Pocket and sliding openings need their frame depths set before modular dimensions are fixed, because the wall thickness they require changes the reveal.
Standing height matters as much as the elevation drawing. Sightlines across a living room or a hotel lounge determine which modules stay open, which get doors and where display niches land. This is where Santerson Floating Modular Systems earn their place: a floating run breaks a full-height wall into bands and keeps the lower zone clear for loose furniture, which also stops that piece of furniture from bridging the flooring expansion gap.
One procurement package, one set of dimensions
When modular systems, cabinetry, panelling, doors and flooring come from separate suppliers, each party issues its own drawings and the junctions are settled on site by whoever arrives first. Ordering them through one fit-out package means a single dimension set: the same team measures the openings, coordinates the finishes across the sample set and releases the modular units against confirmed floor levels and ceiling lines.
That is also where custom furniture design and prototyping earns its place on a project. Where a modular run has to wrap a column, meet a sloping ceiling or integrate an appliance, the detail is drawn and reviewed before production rather than improvised during installation.
Coordinate the delivery sequence, not just the products
Modular units are the last thing you want on site early. They need finished floor levels, completed first-fix electrics and a dry, enclosed space. Our logistics and door-to-door delivery service covers freight by sea, air or rail, customs paperwork, packaging and container loading, with shipment tracking through to the delivery address, so the delivery window can be set against the site programme rather than a factory date. On arrival, installation and after-sales support covers fitting, inspection and snag resolution.
A practical sequence on most projects: first-fix electrics and services signed off, flooring laid and protected, ceiling set-out confirmed, then modular units installed, then loose furniture and rugs placed. Reversing any two of those steps creates rework.
What to send when you request a quotation
- Room elevations with finished floor levels and ceiling heights, plus the position of columns, skirting and any returns.
- The layout brief: open shelving, closed storage, display niches, media or appliance integration.
- The finish set you want matched: cabinetry, panelling and flooring samples or product references.
- Lighting intent: which shelves are lit, where drivers sit, what control the client expects.
- Delivery address, destination market and the site programme date you need the joinery on site.
Send those five items and the coordination questions above are answered in one drawing set instead of across six supplier emails. If drawings are ready, contact our team and we will review them against the modular range before production is scheduled.