A swim spa is one of the few site-furnished items that touches structure, MEP services, finishes and handover documentation at the same time. Before a purchase order for the Outdoor Swim Spa WS-SP500 is signed, procurement teams on villa, resort and estate projects normally clear six risk areas: site access, structural support, electrical supply, drainage, configuration scope and after-sales support. The checklist below follows the catalogue record for this model so each item can be verified against drawings and quotations rather than assumed.

1. Configuration scope: what the quotation actually includes

The published catalogue entry lists a fixed set of standard items and a separate list of options. That distinction is where most change orders begin, so it should be written into the purchase order line by line.

Item shown in the catalogue recordCatalogue value
Shell dimensions5000 × 2500 × 1600 mm
Control system1 set
Swim training system1 set
Water pumpNot listed for this model
Filter pump1 pc
Jet total6 pcs
LED lights4 pcs
Total power9.35 kW
Features shownWater jets, LED lighting, Ozone, Swim training system

Catalogue-listed options include control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so an option that appears on one datasheet is not automatically available on the WS-SP500.

The catalogue record for WS-SP500 leaves the water pump unlisted, while the closely related Outdoor Swim Spa WS-SP500-MS shows a different jet count and total power on the same 5000 × 2500 × 1600 mm shell. Because two variants share one footprint but differ in equipment and load, treat dimensions as site information only — never as proof of performance. Confirm the included equipment list and electrical requirements for the exact configuration in writing before ordering.

2. Electrical supply: matching the connected load to what the site can deliver

Total power is stated as 9.35 kW for the standard catalogue configuration. That figure drives three separate decisions on site, and each one needs a different consultant:

  • the electrical engineer — available supply, dedicated circuit sizing, protection device selection and cable route;
  • the architect or landscape designer — position of the control system, conduit termination and access for future servicing;
  • the client's facilities team — expected running cost, since adding a heat pump or an extra pump changes the load from the number on the datasheet.

Ask for the wiring diagram, control-system specification and voltage requirement for the ordered configuration before the first-fix electrical stage. If a heat pump or additional pump is under discussion, request the revised total power at that point instead of sizing from the base figure.

3. Structural support and ground conditions

A filled vessel of this footprint imposes a sustained load plus live loads from users. Procurement should confirm, before order: the finished external dimensions against the approved layout; the bearing requirement for the chosen installation type (above-ground pad, semi-recessed or recessed); and who is responsible for the slab, plinth or excavation. That responsibility boundary belongs in the contract, not in an email thread.

Where the spa sits on a terrace, podium or timber deck, the structural engineer signs off before the shell is manufactured — dimensions and equipment are fixed at production, so rework after that point is expensive.

4. Access, delivery route and site logistics

A one-piece shell has to reach its foundation. Teams routinely under-plan this: check the delivery address for vehicle access, confirm whether a crane or tail-lift is needed, and verify the path from the drop-off point to the final position. Where the villa or resort site is shared with other trades, agree the delivery window with the main contractor; a late shell blocks the wet-trade sequence.

For international projects this is also where Incoterms, packaging detail, container loading plan and customs paperwork are agreed. SANTERSON describes logistics and door-to-door delivery covering freight forwarding by sea, air and rail, customs documentation, packaging and container loading and shipment tracking. Import duties, terminal charges and on-site unloading remain local line items and should be priced separately in the project budget.

5. Drainage, water supply and water treatment

The catalogue record shows a filter pump and ozone among the standard features, with UV sterilization and sand filtration listed as options. Procurement should decide the treatment approach early, because it determines plant-room space, power points and pipework. Confirm at the same stage: fill-water connection and pressure, drain or overflow route, whether steps are included, and who supplies insulation for colder climates.

6. After-sales, spares and the responsibility matrix

Swim spas fail on consumables and access, not on shells. Before ordering, ask what is covered, what qualifies as a spare part, how a failed pump or controller is replaced, and who performs local work. The site describes installation and after-sales support including on-site installation, inspection and snags, warranty coverage, spare parts and replacement, and ongoing maintenance; the exact warranty term, response time and exclusions for this product category should be confirmed in writing for the destination country rather than taken from general marketing copy.

A one-page responsibility matrix — supplier, main contractor, MEP engineer, client facilities — agreed before order placement prevents most disputes at handover.

Procurement checklist to attach to the enquiry

  • ✓Exact model and configuration code, with the equipment list itemised in the quotation.
  • ✓Written confirmation of items not listed on the datasheet, such as the water pump for this variant.
  • ✓Total power for the ordered configuration, plus wiring diagram and voltage requirement.
  • ✓Finished external dimensions released to the architect and structural engineer before production.
  • ✓Delivery route, lifting method and delivery window agreed with the main contractor.
  • ✓Warranty term, spare-parts list and local support arrangements confirmed for the destination country.

How a single supplier reduces coordination risk

Swim spas rarely stand alone in a villa or resort package. Poolside loungers, pergolas, outdoor dining sets, changing-room joinery, wall finishes and lighting usually come from several vendors, and the interfaces between them are where programme slips occur. Sourcing these together with the spa under one turnkey solution means one specification set, one production schedule and one delivery plan. Where a project needs non-standard sizes, finishes or branding, custom and OEM service covers bespoke material finishes and textures, prototyping and brand customisation — subject to confirmation of options and minimum order quantities for the specific project.

The wider range is catalogued under swimming pools and swim spas, alongside outdoor furniture, interior fixtures and building materials from the same manufacturer, which has operated in furniture and building materials production since 2008.

Send the configuration question before you issue the order Email the model code, installation type and destination country, and request the itemised equipment list, revised total power and warranty terms for that configuration. Contact details are on the contact page.