A sample of flexible travertine veneer often looks identical on two supplier sheets, and the installed wall does not. The difference sits in details buyers rarely put in writing: which colour number was approved, how wide the joint is meant to be, what the substrate actually is, and who signs off a curved run before panels go on the wall. This guide lists the finish decisions worth confirming on a purchase order for MCM flexible travertine stone veneer, an ultra-thin, bendable soft stone cladding that reproduces the pitted surface of natural travertine for interior feature walls and exterior facades on hotels, villas, restaurants, retail and office projects.
Why Finish Confirmation Matters More on a Flexible Cladding Than on a Rigid Slab
With rigid stone, the factory cuts to size and the error margin is in the setting bed. With a thin, flexible sheet that wraps curved walls, cylinders and arched surfaces, the finish result depends as much on site handling as on the panel itself. Colour banding shows up when panels from different production lots are hung side by side without a dry layout. Joint width shifts when installers cut edges cleanly but have no written target for the reveal. Surface sheen changes when the topcoat specified for an exterior elevation is left off, or when an indoor adhesive is used outdoors.
The material itself is straightforward: it is a modified clay soft stone sheet, thin enough to bend onto shaped surfaces and light enough to reduce load on the wall build-up. It cuts on site with simple hand tools, fixes to a cement-based base or gypsum board with tile adhesive, and carries weather-resistant, anti-freezing and anti-crack properties for outdoor elevations. Because the system is forgiving, poor specification gets hidden rather than fixed, which is exactly why the confirmations below belong in writing before production starts.
The Finish Details to Lock Down Before Production
| Detail to confirm | What to specify on the order | Why it goes wrong later |
|---|---|---|
| Colour reference | A named colour code from stock, matched to a physical sample you signed, not a screen image | Travertine-look shades range from near-white to warm beige; on-screen images shift under different lighting and hide batch variation |
| Production lot | All panels for one continuous wall drawn from a single lot number, with the lot recorded on the packing list | Mixing lots across a feature wall produces visible tonal banding that no topcoat evens out |
| Texture direction | Whether the veining and pit pattern has a fixed direction, and how panels are to be rotated during layout | Panels turned at random read as a patchwork once the sheet is up under grazing light |
| Joint width and edge treatment | The target reveal in millimetres, whether edges are butt-jointed or left for a filled joint, and the joint filler colour | Installers default to whatever the site offcut allows; the result varies floor by floor on the same project |
| Minimum bend radius | The tightest curve radius on your drawings, stated as a number, with the manufacturer asked to confirm it before panels ship | A radius that is too tight for the sheet thickness shows stress marks or cracks at the crown of the curve after fixing |
| Substrate and adhesive | The wall build-up behind the cladding - cement board, render, gypsum board - and the matching tile adhesive type for interior or exterior use | Exterior elevations fixed with an interior-grade adhesive lift at the joints after the first freeze-thaw cycle |
| Topcoat / sealer | Whether a protective coating is supplied or applied on site, and which manufacturer product is approved for that surface | Unsealed exterior faces pick up staining; an unapproved sealer can change the matte stone look to a plastic sheen |
| Cut-edge handling | Who finishes cut edges - factory or site - and whether touch-up paint is shipped with the panels | Bare cut edges expose the core colour against the finished face, most visible at internal corners and reveals |
Curved Walls and Special-Shaped Surfaces: Confirm Before Panels Ship
The reason buyers choose a bendable soft stone over rigid cladding is geometry. Arch heads, cylindrical columns, reception desks, curved reception walls and feature niches are the runs where this material earns its place - and they are also where finish disputes start.
- Send the actual setting-out drawing with radii marked, not a photograph of a curved wall. Ask for written confirmation that each radius is within range for the panel thickness being supplied.
- Agree how panels break around a curve: continuous wrap or segmented runs with a joint at the springing line. Segmented runs need a joint detail drawn to scale.
- Confirm whether the curve is fixed on site over a prepared curved substrate or pre-formed off site. The two methods need different panel sizes and different adhesive open times.
- Ask for a bent sample - a piece wrapped around a former of your stated radius - in the same shipment as the flat samples, so you can inspect the finish on the curve before ordering the full wall.
Interior Feature Wall vs Exterior Facade: Different Confirmations
The same panel line covers both applications, but the approval list splits at the elevation line.
Interior feature walls - hotel lobbies, restaurant fronts, villa living rooms, retail
- Confirm the substrate is flat and within tolerance before fixing; a thin flexible sheet follows rather than bridges surface movement.
- Agree the adhesive for gypsum board or cement board, and who carries out priming if required.
- Decide joint treatment: tight butt joints read as continuous stone; filled joints read as tiled. Both are legitimate - pick one per wall and note it on the drawing.
- Confirm protection during the rest of the fit-out; soft stone faces chip at arrises when other trades work past them.
Exterior facades and elevations
- Confirm exterior-grade adhesive and joint filler, plus the detailing at parapets, window reveals and any horizontal capping where water can collect.
- Ask how panels are to be handled around movement joints and building expansion lines.
- Record the exposure of each elevation on your order. A shaded north face and a sun-facing west wall age differently even with identical material.
- Agree who inspects the finished elevation after the first wet season, and what is covered under replacement of damaged panels.
For projects mixing stone-look elevations with other surfaces, it is worth reviewing the whole wall and ceiling palette at once. SANTERSON's wall panels and wall cladding range sits alongside aluminium honeycomb panels for exterior and interior cladding and flexible wood grain cement panels, so a single specification round can settle stone, metal and timber-look finishes together instead of one product at a time. Related soft-stone options include the MCM flexible rammed earth panel for projects wanting an earthy, rammed-wall texture on curved and shaped surfaces.
A Buyer's Pre-Order Checklist
- Signed physical colour sample, with the code recorded on the order and the packing list.
- Single production lot per continuous wall run; quantities stated per elevation, not as one lump sum.
- Setting-out drawings with radii marked for every curved run, returned with written confirmation.
- Joint width, edge treatment and filler colour specified per wall.
- Substrate type and adhesive grade confirmed for each interior and exterior elevation.
- Cut-edge finishing and touch-up material assigned to a named party, with material shipped together.
- Panel protection and sequencing agreed with other trades on site.
- Spares ordered with the main quantity - cutting replacement panels from a later lot is where colour mismatch appears.
If your project groups wall finishes with flooring, joinery, lighting and loose furniture, one procurement package usually runs smoother than separate orders. SANTERSON works as a one-stop furniture and building materials supplier for villa, hospitality and office projects, covering custom/OEM production, door-to-door logistics and installation support, which means the wall cladding specification can be settled in the same detail round as the rest of the fit-out.
Request samples and a finish confirmation sheet for your project
Send your elevation drawings, radii for curved runs and target colour direction, and the SANTERSON team will confirm panel specification, lot supply and installation requirements before production. Contact us to arrange samples.