A 9.95-metre swim spa is a serious line item on a villa or resort bill of quantities. Before a buyer signs off on Outdoor Swim Spa WS-130BⅨ, the comparison work should be done properly: footprint against site, configuration against intended use, and what is actually included in the quotation against what the spec sheet implies. This article sets out the checks that decide whether the model fits the project or whether a sibling in the same range does.
Start With the Footprint, Not the Feature List
The catalogue lists WS-130BⅨ at 9950 × 3000 × 1430 mm. That length is what separates it from the shorter shells in the same family, and it should be read against your slab, setbacks, plant-room access and delivery route before anything else is discussed. A swim spa that cannot be craned or walked into position on site is not a specification problem — it is a procurement failure.
For context within the range: Outdoor Swim Spa WS-125AⅨ is catalogued at 5500 × 2300 × 1350 mm, and Outdoor Swim Spa WS-130AⅨ at 8000 × 3000 × 1400 mm. If the site can take a metre and a half more length, Outdoor Swim Spa WS-130CⅨ is listed at 11830 × 3000 × 1430 mm. Ask the supplier for the shipping dimensions and the lifting points as well as the installed shell size — the two numbers are not the same, and the delivery drawing is where most disagreements start.
Read the Swim Training System Line Carefully
WS-130BⅨ shows a swim training system (1 set) among its features, alongside water jets, LED lighting and ozone. That is the feature that turns the shell into a place to swim against a current rather than only to soak. It matters because the "-U" variants in this family are documented differently: for Outdoor Swim Spa WS-130BⅨ-U, the published specification sheet does not show a swim training system, while the water pump count and jet count are higher.
So the comparison is not "which model is better" but "which job is this for". A hotel or private residence that wants lap swimming needs the swim current confirmed in writing. A wellness area whose priority is jet massage and seating may be served by a different variant at a similar length.
Compare the Numbers That Are Published, Then Confirm Them
The figures below are transcribed from the catalogue entries for these models. Treat them as the starting point of the conversation with the factory, not as a purchase order description — included equipment and electrical requirements change with the selected configuration.
| Item | WS-130BⅨ | WS-130BⅨ-U |
|---|---|---|
| Catalogue dimensions | 9950 × 3000 × 1430 mm | 9950 × 3000 × 1430 mm |
| Swim training system | 1 set | Not shown for this variant |
| Water pump | 1 pc | 4 pcs |
| Filter pump | 1 pc | 1 pc |
| Jet total | 20 pcs | 23 pcs |
| LED lights | 7 | 5 |
| Total power | 10.85 kW | 11.85 kW |
| Control system | 1 set | 1 set |
Two things in that table deserve attention from anyone writing the electrical scope. First, total power is quoted at 10.85 kW for WS-130BⅨ and 11.85 kW for WS-130BⅨ-U — both are substantial loads that must be reconciled with the available supply, the distribution board and, where a heat pump is added, the running load of the heating system as well. Second, a pump count of one versus four is not decoration; it changes jet performance, wiring, protection devices and the maintenance access you will need later.
Options That Change the Price More Than the Model Name Does
The catalogue lists options across this range including control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so each option should be confirmed for the exact unit being quoted. Three points decide most of the difference between two quotations:
- Heat pump and insulation are what determine whether the spa is economical to hold at temperature through a cold season. Ask for the configuration as an itemised list, not as "fully equipped".
- Filtration choice — standard filtration versus the sand filtration option — drives the service routine your maintenance team will actually follow. The cheaper unit with the wrong filtration system becomes a cleaning problem.
- Steps and access affect the surrounding deck detail. Decide them before the paving is ordered, not after installation.
Judge the Supplier on the Whole Delivery, Not the Datasheet
A swim spa arrives as a crated shell plus a plant set, and it has to be landed, levelled, connected, tested and handed over. That is why many buyers now work with a one-stop furniture and building materials supplier rather than buying the spa in isolation: when the same party also handles the adjacent scope — outdoor furniture on the deck, wall and ceiling finishes around an indoor installation, bathroom fixtures in the adjoining change room — there is one coordination point instead of five.
SANTERSON is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with services described on the site covering design and specification support, custom/OEM production, freight and door-to-door delivery, installation and after-sales support. For buyers assembling an Australian project package, that single coordination point is where sourcing decisions get settled — see logistics and door-to-door delivery and installation and after-sales support. Freight terms, duties, insurance and transit time should be agreed case by case in writing; the spare-parts and service arrangements for a water plant should be confirmed before order, not at handover.
A Practical Checklist Before You Issue the Purchase Order
- Site: slab loading, finished floor level, clear delivery path, lifting method, plant access for the filter pump and jets.
- Configuration: written confirmation of which features are included on WS-130BⅨ — swim training system, jet count, LED count, ozone — versus what is optional.
- Electrical: total connected load confirmed against your supply, protection devices, and the added load if a heat pump is selected.
- Water treatment: filtration type, dosing or sterilisation option, and the maintenance routine you are willing to run.
- Envelope: humidity control, drainage, deck and step detail, and finishes that tolerate the room's conditions.
- Commercial: Incoterms, packaging and container loading plan, spares list, warranty terms and who performs commissioning on site.
If you are evaluating WS-130BⅨ for a specific project, send the floor plan and the intended use — daily lap swimming, guest wellness, or seasonal outdoor leisure — and ask for two configurations priced against that brief. The model comparison then becomes an ordinary decision instead of a guess.
SANTERSON — furniture and building materials manufacturing and project supply since 2008, with offices in China, Vietnam, Singapore and South Africa. Enquiries: Contact.