A walnut wardrobe is one of the more expensive line items in a bedroom fit-out, and it is also one of the easiest to get wrong when the order crosses an ocean. The drawings look fine, the quotation looks competitive, and then the units arrive with the wrong heights, a finish that does not match the sample, or carcasses that no local joiner wants to assemble. Most of those problems are decided before production starts, in how clearly you specify the job and what the factory is obliged to confirm back. Here is how we handle walnut solid wood wardrobes for villa, apartment and hotel projects, and what to insist on at each stage.

Start With the Wardrobe Type, Not the Wood

Buyers usually open a conversation with "walnut, solid wood, floor to ceiling". That is three decisions in one sentence, and it leaves the two that matter most unstated: how the unit is built, and how it is installed.

Our Walnut Solid Wood Wardrobes sit inside the wider Solid Wood Wardrobes collection, alongside Oak, Cherry, Mahogany and Rustic versions. What carries across the whole collection is the make-to-measure approach: sizing is made to the opening rather than picked from a size grid, material and finish are selected per project, and the internal layout is drawn around how the space will actually be used. The same walnut look is also available as part of our Wood Veneer Wardrobes range, so the door face and the substrate behind it are separate decisions that should be quoted separately.

Decide the type first because it changes what you send to the factory. A hinged wardrobe needs clearance for the door swing. Sliding doors need a track depth and a ceiling-fixed head rail. A walk-in run needs an island or a return wall. A corner unit needs a decision about whether the corner bay is usable storage or just dead space with a hanging rail across it.

What to Specify Before You Ask for a Price

A quotation built on a rough sketch is not comparable to anything else you receive. Send these six items and the numbers you get back will actually line up:

  • The opening, measured in three places per wall. Floors and ceilings are rarely square. Give us the low point and the high point, not one average figure.
  • Door type and hardware expectation. Hinged, sliding or open; soft-close or standard; visible handles or a handleless groove.
  • Internal layout by zone. Long-hang, double-hang, drawer bank, shelf stack, trouser tray, lighting. Say what each zone is for.
  • Which surfaces are walnut and which are not. Door faces and visible ends only, or carcass, shelves and interior too.
  • Finish and sheen. Matte, satin or gloss, plus whether you want the grain open or filled.
  • Site conditions. Skirting boards, recessed services, uneven plaster, whether the unit butts into another run of joinery.
If a supplier quotes from a single elevation with no dimensions marked, treat that quotation as provisional. The variation almost always lands after delivery.

Solid Wood or Veneer: Choose Deliberately

This is where projects go over budget or under-expect. Both options are legitimate and both are in the catalogue; they simply answer different questions.

ConsiderationSolid wood constructionVeneered construction
AppearanceThrough-colour timber, grain continues over edges and profiles; can be sanded back on site.A thin walnut face over an engineered substrate. Very consistent figure across a long run.
MovementTimber moves with humidity. Construction has to allow for it, particularly on wide panels.Engineered substrates are dimensionally steadier in conditioned rooms.
Cost driverMore timber, more machining, more hand finishing.Lower material cost; the finish quality depends on pressing and edge banding.
Best fitPieces where edges and mouldings are visible and meant to be read as timber.Floor-to-ceiling slabs, handleless fronts, matching large panels across a bedroom wall.

The comparison above is general joinery guidance. Exact construction, substrate and finish for your order are set in the shop drawings and material schedule we issue with the quotation.

Our Walnut Veneer Wardrobes are built on the same make-to-measure basis as the solid wood line, with finish, layout and dimensions specified per project. A practical way to split the two is to use solid timber where the eye touches the piece — doors, drawer fronts, visible ends — and a walnut face on carcass panels and interior surfaces, then have both quoted as one package so the grain and sheen still match.

Ask How the Factory Confirms Dimensions

This is the single highest-value question in overseas sourcing of built-in furniture. Site measurement is either yours or ours, and the answer changes your risk.

For whole-house joinery packages we carry out on-site measurement as part of the work, with all cabinet dimensions taken to match appliances and layout, then 3D design, production, delivery and installation follow as one sequence. For a wardrobe-only order shipped from our factory, the normal route is that you send measured drawings and we return shop drawings for your sign-off before any board is cut. Either way, insist on the second set of drawings. Read the heights, the door weights against the hinges quoted, and where the carcass meets a sloping ceiling.

Get the Finish Approved Before Production

Walnut reads differently under lacquer than under oil, and it photographs nothing like the room it will stand in. Ask for a finish sample on the actual door construction you have ordered — not a colour card. Check it in the site's daylight and its artificial light before you approve.

Two details cause most disputes: sheen level, and how much of the open grain is left visible. Both should be written into the order confirmation with the sample reference, because "as per sample" means nothing once the sample is back in your office and the container is on the water.

Packaging, Freight and What Arrives

Wardrobes are awkward freight: tall panels, heavy doors, hardware that scratches a finished face if it travels loose. Confirm in writing how the units travel — panel thickness of protection, whether doors ship hung or detached, how ironmongery is separated and labelled, and how the cases are numbered against the room plan so the installer knows which crate is which wall.

We arrange freight by sea, air and rail with customs paperwork and door-to-door delivery, which means one party carries responsibility from the factory floor to your site rather than handing you a bill of lading and a problem. For built-in joinery, sea freight with proper case marking is the usual choice; air tends to make sense only for a small replacement batch.

Whatever route you choose, photograph the cases on arrival before unpacking, and check the panel count against the packing list while the delivery driver is still present. Claims made after the crate is opened are difficult to substantiate.

Installation: Decide Who Does It

Built-in wardrobes need levelling against imperfect walls, scribing to ceiling lines, and fixing into substrates that may not be where the drawings say they are. You have three options: your own joiner with our shop drawings; a mixed arrangement where we supply and your trades install; or installation handled as part of a wider fit-out with inspection and snagging included.

Whichever you pick, agree in advance who is responsible for the gap between the wardrobe and an out-of-plumb wall, and who fills it. That one clause settles more arguments than any other line in the order.

A Pre-Order Checklist

  • Opening measured in three places per wall, with low and high points recorded
  • Door type, clearance and hardware expectation stated
  • Internal layout drawn by zone, not left to the supplier
  • Solid walnut versus walnut veneer decided surface by surface
  • Finish sample approved in site conditions, with sheen and grain written into the order
  • Shop drawings returned and signed off before cutting
  • Packaging, case numbering and freight mode confirmed in writing
  • Responsibility for scribing, levelling and snagging assigned to one party

Sourcing Wardrobes as Part of a Wider Package

If the wardrobes are one part of a bedroom or whole-house fit-out, ordering them alongside the rest of the joinery removes the matching problem entirely. Wardrobe fronts, sideboards, vanity units and kitchen cabinets from one manufacturer can share one walnut species, one stain batch and one lacquer schedule. That is also where custom furniture manufacturing earns its keep: dimensions, storage layouts, materials and finishes are all built to your drawings rather than adapted from a standard range.

The same logic applies across a project. As a one-stop furniture and building materials supplier, we produce wardrobes alongside engineered European oak flooring, doors, wall panelling, lighting and bathroom ceramics, so the walnut of a bedroom run can be matched to the timber used elsewhere in the same specification instead of being reconciled after the fact by two different vendors.

Send us your floor plan, the measured openings and any reference images for the finish you have in mind. We will come back with shop drawings, a material and finish schedule, and an itemised quotation covering the wardrobes, hardware, packaging and delivery to site — before anything goes into production.