A materials schedule that lists wardrobes as one line item is where most finish-related rework begins. This guide shows how to break high gloss lacquer wardrobes into schedule-ready entries, so the specification, the sample approval and the delivered product all describe the same thing.
On a whole-project fit-out, wardrobes rarely stand alone. They sit beside built-in furniture, flooring, wall panelling and doors that share the same walls, the same sightlines and often the same colour reference. If the wardrobe line in your materials schedule only says "high gloss, white", three different suppliers can produce three different whites and all of them are technically compliant. The schedule has to carry enough detail to survive quotation, sampling, production and site installation without anyone re-interpreting it.
Start from the room set, not the single wardrobe
High gloss lacquer reads differently depending on what surrounds it. The same panel looks warmer next to whole-house custom cabinetry in a warm wood grain and cooler next to stone or glass. Before you write the wardrobe line, group it with everything that will be visible from the same standing position: vanity units, tall cabinets, shelving, internal doors and skirting. That grouping decides how many finish variants you actually need.
In practice, one bedroom tower, one hallway bank and one walk-in robe rarely share a single entry either. Layout differs, door type differs, and the amount of reflected light differs. Split entries by location so that substitutions later on can be assessed room by room instead of across the whole project.
What each schedule line must carry
For made-to-measure lacquer joinery, a workable line item carries the following fields. Missing any one of them is what turns a straightforward order into a site variation.
| Schedule field | What to record | Why it matters on site |
|---|---|---|
| Location and reference code | Room name plus a unique item code, repeated on drawings | Keeps the drawing set, the quotation and the delivery note describing one unit |
| Overall dimensions and tolerance | Width, height, depth; whether the unit runs floor to soffit or floor to finished ceiling | Determines whether packing, flooring or cornice is cut around the unit |
| Door type and opening | Hinged, sliding or open; number of leaves; clearance for handles | Sliding and hinged wardrobes need different structural and floor clearances |
| Finish name and sample reference | Exact finish name plus the physical sample or panel reference you approved | "High gloss white" is not a specification; the approved sample is |
| Interior configuration | Shelves, drawers, hanging rails, pulls, lighting provisions | Interior parts are often quoted separately and arrive in a different crate |
| Edge and profile detail | Door edge profile, handle or handleless groove, matching trims | Visible edges define the look; unspecified edges get decided by the factory |
| Related items | Cross-reference to flooring, wall panelling and doors in the same room | Makes a colour or material change traceable across trades |
| Approval status and date | Who approved which sample and when | Protects you when a finish is revised after production starts |
Handle the gloss level as a separate field
"High gloss lacquer" covers a range of surface reflectivity, and panels from different batches can differ noticeably under the same lighting. Write the gloss expectation as its own line entry with an approved physical panel, rather than folding it into the colour name. Where a project mixes finishes in one run — for example matte lacquer wardrobes beside high gloss doors, or two tone lacquer wardrobes in a bedroom — schedule each finish separately and note which surfaces they will be seen against.
Glass-fronted variants need their own entry as well. A glass and lacquer combination wardrobe brings glazing type, glass tint and framing into scope, none of which belong in a plain lacquer line.
Tie the schedule to the sampling sequence
A materials schedule only works if it is dated against the sampling programme. For custom-built wardrobes the practical order is:
- Issue the draft schedule with candidate finishes marked as "to be sampled".
- Request physical panels for every finish you intend to use, including interior decorative surfaces.
- Check each panel on site, against the actual wall and floor finish and under the installed lighting.
- Record the approved reference in the schedule and freeze that line before production release.
Checking a lacquer panel on a desk at head office is not the same test. Gloss surfaces shift with light direction, and a colour approved against the wrong flooring sample is the most common cause of late replacement orders.
Coordinate the wardrobe supplier with adjacent trades
Where one supplier provides several built-in elements, the schedule should show that grouping explicitly. A project that sources wardrobes, media walls and custom built-in kitchen cabinets from the same manufacturer can match lacquer batches across rooms; a project that splits them cannot assume a match. State which grouping applies in the notes column so nobody discovers the mismatch at handover.
The same logic applies to services around the product. Site survey, shop drawing approval, production, delivery and installation each sit at a different point in the programme. For projects handled as turnkey furniture and fit-out supply, list those stages against the wardrobe item so the site team knows who is responsible for measurements and who signs off the final installation.
A worked example
A bedroom in a villa renovation might carry this entry:
- Item BR-01 — Made-to-measure wardrobe, hinged doors, floor to finished ceiling, opening width as per drawing BR-2.
- Finish — High gloss lacquer, approved panel reference HG-WH recorded on the dated approval sheet; interior in matching matte decorative surface.
- Configuration — Two hanging sections, four drawers, four adjustable shelves, integrated LED provision to top section.
- Related items — Engineered oak flooring (room BR), skirting to match wardrobe carcass, internal door set BR-02.
- Status — Sample approved; released to production with shop drawing signed by the site architect.
That entry can be quoted, sampled, produced and inspected without a phone call. An entry that says "wardrobe, white gloss" cannot.
Schedule discipline checklist: one line per unit location; dimensions tied to a drawing number; finish named and backed by an approved physical panel; interior configuration itemised; related finishes cross-referenced; approval dated. Six fields, and the wardrobe line stops being an assumption.
SANTERSON manufactures made-to-measure lacquer wardrobes with configurable layouts, door types and finish options, alongside other built-in furniture for villa and hospitality projects. Send us your draft materials schedule and we will return a quotation, physical finish samples and shop drawings aligned to it.
Contact: PHILLIP | Phone / WhatsApp: +86-13928214007 | Email: santerson@qq.com | Enquiry page