Most bathroom fixture enquiries that stall did not fail on price. They failed because the drawing package and the enquiry note described different things. A designer wants a square-rounded rim, a supplier quotes an oval bowl, the plumbing riser is on the floor, and the quoted trap is for a wall outlet. The Washdown One Piece Toilet 1004A is a good test case for this: one fixture, two plumbing routes, and a finish requirement that has to survive housekeeping. Below is the practical sequence we use to convert a design brief into an enquiry that a manufacturer can quote without guessing.
Start with what the brief already tells you
A usable brief for a WC suite usually contains four things: the room schedule, the fixture layout drawing, the finish and style intent, and the drainage note. If all four exist, specification is fast. If any one of them is missing, an enquiry will come back with alternatives rather than a firm price, because the manufacturer has to protect themselves against an installation failure.
Read the room schedule first for quantity by room type. A guest bathroom, a main ensuite and a staff or commercial restroom rarely carry the same fixture specification, even in one building. Then read the layout drawing for the waste outlet location, because that single dimension decides which of the two installation routes you can use.
Confirm the drainage route before anything else
The 1004A supports two plumbing installation ways: a P-trap wall drain with a 180 mm rough-in, and an S-trap floor drain with a 250 mm rough-in. That is the decision point that most often kills a late order. Wall-hung drainage and floor drainage are not interchangeable at site level; changing one to the other means chasing pipework, boxing, and in a retrofit sometimes a slab.
So before you write the enquiry, put this line in it:
- Waste outlet type: wall (P-trap) or floor (S-trap).
- Rough-in dimension as shown on the drawing, not as assumed from a previous project.
- Whether the dimension is measured to finished floor and finished wall face, or to structural substrate.
Translate style language into fixture geometry
Design briefs describe intent: "clean lines", "minimal", "softened edges". Manufacturers quote geometry. For this model the geometry is a square-rounded silhouette with a one-piece integrated structure, meaning there is no separate tank and bowl joint. That detail matters twice over. It removes the gap where dirt and bacteria collect, which is exactly what housekeeping complains about in hospitality rooms, and it changes how the unit sits against the wall compared with a two-piece close-coupled WC.
When you write the enquiry, replace adjectives with the physical features you actually need:
| Brief language | What to write in the enquiry |
|---|---|
| "Modern look" | Square-rounded profile, concealed or minimal visible seams between pan and cistern. |
| "Easy to maintain" | Dense glossy glaze specified as stain, limescale and yellowing resistant; no open joint at the tank-to-bowl interface. |
| "Consistent across floors" | Same model code on every bathroom in the schedule, with a note where a room type genuinely differs. |
| "Strong flush" | Washdown flushing mechanism; state whether the water supply pressure and cistern inlet shown on your drawing match the fixture requirement. |
State the application, because it changes what gets quoted
The same ceramic pan behaves differently in a private villa and in a hotel room turned over daily. In hospitality and commercial restroom upgrade work, you are buying a maintenance cycle, not just a shape. That is where the vitreous ceramic body and its glaze do their work: a dense, glossy surface resists staining and limescale build-up, which keeps the unit looking correct between deep cleans rather than only after one.
Tell the supplier who will use the fixture and how often it is cleaned. If you are sourcing for a hotel or a villa project, mention it in the same sentence as the model code. As part of a wider fit-out, this is also where interior fixtures get grouped: basins, showers, vanities and WC suites on one schedule are easier to coordinate than fixtures bought as separate line items from separate suppliers.
Write the enquiry so it can be quoted without a second round of questions
A complete enquiry for this fixture carries:
- Model code and product page link, so there is no ambiguity about which pan you mean.
- Quantity by room type, with the room schedule attached.
- Drainage route and rough-in per the current drawing revision.
- Seat and cover requirement, including soft-close if specified.
- Inlet and supply detail from your plumbing drawing.
- Delivery destination and the packaging or pallet expectation for the site.
If you are also ordering other finishes for the same building, send them together. SANTERSON works as a furniture and building materials supplier, so ceramics can sit on the same schedule as cabinetry, wall and ceiling finishes, lighting and flooring. One coordinated order is one set of drawings to reconcile and one shipment window to plan around, instead of five.
Agree the specification before production starts
Where a project needs a non-standard detail — a different finish, a bundled configuration, an order that does not match catalogue quantity — raise it at enquiry stage rather than after the schedule is fixed. Custom and OEM work covers bespoke finishes and configurations, and it only helps you if the request reaches production planning before cutting begins. See the Custom & OEM service page for what can be specified, and confirm current options and minimum order quantities for your particular project.
Plan the delivery and installation handover at the same time
Ceramics arrive in crates and they are inspected on arrival. Put three items into the enquiry that most buyers leave to the last week:
- Packaging and container loading arrangement, and how the goods will be handled at your delivery point.
- The inspection and snag list for damaged ceramic on arrival, agreed before dispatch rather than after.
- Who sets out and fixes the pans on site, and what tolerance the tiler needs to work to.
Door-to-door delivery covers freight, customs paperwork and tracking; installation and after-sales support cover fixing, snagging and spare parts. Read both as service descriptions and confirm the actual terms for your country in writing — import duties, Incoterms, transit time, warranty scope and exclusions are project-specific and should never be assumed from a brochure.
A short pre-send checklist
Send the enquiry only when these are answered
- Model code 1004A named, with the product page linked.
- P-trap or S-trap selected, and the matching rough-in figure taken from the current drawing revision.
- Quantities split by room type.
- Seat, cover and inlet requirements stated.
- Application stated (villa, hotel, commercial restroom upgrade).
- Delivery destination and arrival inspection arrangement stated.
- Any custom or OEM request raised now, not later.
The point of this sequence is simple: every line in the enquiry removes one question the manufacturer would otherwise ask, and one variation order you would otherwise receive. When drainage, geometry and application are all stated up front, a modern ceramic bathroom toilet enquiry becomes a quotation instead of a conversation.