Open corner wardrobes sit at an awkward point in most hospitality schedules: too detailed to leave out of the base build, yet usually ordered after the room concept is fixed. Handled as a separate line item, they turn into change orders and clashing finishes. Handled inside the joinery package, they are simply another made-to-measure unit. This guide sets out how buyers, contractors and project managers can specify, price and sequence them without surprises.

Where Open Corner Wardrobes Belong in a Hospitality Package

A corner wardrobe is not a piece of loose furniture. It is fixed joinery that has to reconcile with flooring, skirting, wall linings, ceiling lines and door openings. In guest rooms, serviced apartments and villa suites, the corner is often the only place tall storage fits without blocking a circulation route or cutting across a sliding door track.

The "open" part of the specification matters just as much. An open corner wardrobe is a carcass without doors: hanging rails, shelves and drawer banks stay exposed. That choice changes the budget line, the detailing standard and the housekeeping routine, so it should be a design decision taken early rather than a cost-cutting note raised during tender.

Where this configuration usually appears

  • Compact guest rooms — an open carcass removes door panels and their clearance, which frees front-of-wardrobe space in narrow rooms.
  • Serviced apartments and long-stay suites — guests need visible hanging space, luggage shelving and drawer storage without hunting for a mirror or handle.
  • Villa suites and walk-in dressing areas — open runs read as fitted dressing rooms and pair naturally with an open walk-in wardrobe on the adjacent wall.
  • Showroom units and display floors — merchandising stock is presented rather than concealed, so doors add cost with no benefit.

Decide Early Whether "Open" Is the Right Answer

Open storage is not automatically cheaper or simpler. Because nothing hides the interior, every visible surface becomes a finished surface. Before you release the enquiry, weigh the trade-offs against your operating model.

FactorOpen corner wardrobeDoored corner wardrobe
Carcass finish standardAll interior faces, edges and shelf fronts must match the exterior specification.Interior faces can use a lower-cost finish behind doors.
HardwareRails, shelf supports, drawer runners and soft-close fittings stay visible and are part of the look.Hinges, handles and door stays dominate the hardware schedule.
Daily upkeepDust and guest items show immediately; housekeeping needs a defined presentation standard.Contents are concealed; cleaning is limited to door faces.
Installation sequenceFitted after wet trades and flooring, but contents must be protected from that point on.More tolerant of dust during the final site phase.
Typical use caseLong-stay suites, villas, display units, dressing areas.Standard transient guest rooms.

A practical rule: specify open storage where guests live in the room for days or weeks, and doored storage where housekeeping controls the room daily. Mixed projects can carry both, provided the interior carcass build is identical and only the door line changes.

Reading the Manufacturer's Configuration Sheet

Made-to-measure suppliers publish short configuration sheets rather than fixed spec tables. SANTERSON's corner wardrobe records, for example, list three variables — made-to-measure sizing, material and finish options, and a layout tailored to the project — with a standing note that dimensions and selected specifications are confirmed per project. That is normal for built-in furniture, but it means the buyer carries the burden of defining what "confirmed" actually contains.

Treat an unspecified configuration as an incomplete quotation. Push each variable into something measurable before you compare two suppliers on price.

Sizing

  • Send both finished dimensions and the structural opening, with floor-to-ceiling heights taken at the corner itself rather than at the wall face.
  • State which side of the corner is dominant — a returned run that stops short of the wall behaves differently from a full mitred carcass.
  • Record obstructions: skirting depths, AC grilles, sprinkler heads, curtain boxes and door swings.

Materials and finishes

  • Name the board substrate, the surface material and the edge treatment separately. Edge banding on exposed open shelving is the detail most often value-engineered out and most visible afterwards.
  • Ask for the finish sample to be signed off as a physical reference, not a printed or screen image.
  • Match the wardrobe to the rest of the joinery package — vanities, minibars, door linings and skirting — at the sample stage, before any production release.

Internal layout

  • Fix hanging heights, shelf spans and drawer banks on a room-by-room elevation. Corner layouts waste space quickly if the diagonal return is left to the factory.
  • Confirm load assumptions for luggage shelving; a shelf carrying two suitcases needs different support than one holding folded linen.
  • Decide where lighting, if any, is wired and who supplies it — joinery contractor or electrical contractor. This gap causes more site delay than the wardrobe itself.

Consolidating Wardrobes Into the Joinery Package

The single largest saving on this line item is rarely material; it is coordination. Every separate supplier means another drawing set, another sample round, another delivery window and another snag list. When cabinetry, wardrobes, vanities and wall panelling come from one manufacturer, finishes are matched at source and site tolerances are resolved once.

SANTERSON's wardrobe range is catalogued as built-in furniture across several collections, which is useful for a project team specifying a family of related units: L-shaped corner wardrobes for rooms where storage runs along two walls, and minimalist open wardrobes for the straight runs in the same room. Ordering these as one package keeps carcass construction, edge detail and veneer or laminate batch consistent across the guest floor.

Procurement note: a supplier offering design coordination, custom/OEM work, door-to-door logistics and installation support lets you merge several trade packages into one contract. That is where wardrobe procurement stops being a standalone purchase and becomes part of the fit-out programme.

Build the Enquiry Pack Before You Ask for Prices

Quotation cycles are where most of this line item's cost is lost. A complete enquiry produces comparable prices; an incomplete one produces three numbers that cannot be compared.

  • Room-by-room elevations with the corner detail drawn, not implied
  • Finished dimensions and structural openings, marked on the layout drawing
  • Named substrate, surface material and edge treatment for every visible face
  • Signed finish reference from a physical sample
  • Internal layout schedule: rails, shelves, drawer banks, luggage positions
  • Unit quantities by type, plus spares or mock-up units if required
  • Delivery address, packaging standard and unpacking responsibility
  • Who installs, who fixes wall gaps, and who signs off the snag list

Ask each bidder to confirm lead time per batch as well as for the full order. Phased releases — first a mock-up room, then the guest floor — are common on hospitality work, and a supplier who cannot split production cleanly will push you into storing stock or accepting a single site delivery.

Logistics, Site Sequence and Handover

Built-in wardrobes arriving from overseas manufacturing need the same planning as any other long-lead joinery. Confirm the packaging standard for exposed shelf fronts, agree who receives and inspects containers, and check that the site can store units flat and dry until the wet trades are complete.

Sequence matters more than people expect. The correct order is: flooring laid, wall linings and paint completed, then carcasses fitted. Fitting earlier exposes finished interiors to paint overspray and impact damage; fitting later collides with the handover window. For open units specifically, agree a protection standard between installation and guest arrival.

At handover, inspect against the signed sample and the elevation drawings rather than against a catalogue image. Record any deviation in edge banding, rail height or shelf span in writing at that point — after guests check in, those notes carry far less weight.

A Short Timeline to Work Backwards From

StageWhat must be closed out
Concept / design developmentOpen or doored decision; corner positions on the room layout; joinery package boundaries agreed.
TenderFull enquiry pack issued; comparable quotations; finish references signed.
Production releaseFinal elevations confirmed per project; batch and phased-release schedule agreed.
LogisticsPackaging standard, shipping mode, delivery window and storage plan fixed.
Site installationFlooring and linings complete; units fitted; gaps closed; protection applied.
HandoverInspection against signed sample and drawings; snag list closed in writing.

Nothing in that sequence is wardrobe-specific, which is the point. Treating open corner wardrobes as one node in the joinery programme — rather than a late accessory decision — is what keeps the specification honest and the cost predictable.

Specify your wardrobe package with the joinery, not after it.

Send your room elevations, target finishes and unit quantities, and confirm sizing, layout and finish options project by project before production is released.