A glass-front door is the one part of a kitchen that every guest sees and every buyer argues about. Before we press a single sheet for your Santerson Glass Front Pvc Cabinet, we send you physical samples so the finish, the glass and the frame are agreed in writing — not argued about after the container has left the port. Here is exactly what arrives in the sample pack, how to judge it on your own site, and what you sign off before production starts.

Why a PVC cabinet with glass doors needs a sample round

PVC-wrapped door panels and glass behave differently from a solid painted door under the same light. The wrap film changes appearance with its sheen level and the direction of the grain; tinted and textured glass shifts colour depending on what is behind it and how strong your lighting is. A render cannot settle any of that. A physical sample placed in the actual room can.

The glass front PVC cabinet is made to measure for each project, with material and finish options selected per order. That flexibility is the reason we insist on a sample round: the specification you approve is the specification that goes into production, so the decision has to be made once, properly, before cutting begins.

What the sample pack contains

For this product line we prepare the pack around the three elements a buyer actually needs to compare:

Item in the packWhat you are checking
PVC wrap panel, in the selected colour and grainColour match against your tiles, benchtop and wall finish; sheen level; grain direction and embossing depth; edge wrap quality at the profile corners
Glass sample in the chosen typeTint and clarity when lit from the front and from inside the cabinet; how much of the contents you want visible
Frame profile offcut and hardware referenceFrame colour and width against the door panel, how the joint sits at the glass rebate, and the hinge and handle style in the finish you have chosen, so metal tones are agreed with the frame rather than left to chance

If your project also calls for solid doors in the same run — a common mix is glass-front uppers with closed lowers — we include the matching panel in that finish too, so you can confirm the two read as one set rather than two products from different factories.

How to judge the samples on site

Do not assess the pack on a desk under showroom lighting. Take it to the room where the cabinets will stand and work through this sequence:

  • Check it at three times of day. Morning daylight, afternoon light and your own lights switched on after dark give three different readings, especially for glossy and metallic finishes.
  • Stand the panel vertical, not flat. A wrap film laid flat catches light differently from a door hung upright. Prop it against the wall at cabinet height.
  • Put the glass against both a dark and a light background. Tinted glass over a dark carcass and over a white one look like two different products; you need to see which combination you are approving.
  • Look at the edges, not only the face. Run a thumb along the wrap edge and check the corner joints. That is where a poorly wrapped panel fails first in daily use.
  • Compare against your other finishes side by side. Hold the tile, benchtop and paint sample next to the door panel under the same light source before deciding.
Mark up the physical samples with a grease pencil or masking tape: number them, note the finish code on each, and photograph them in place. That photo set becomes your approval record and removes any argument later about which sample was signed off.

What you confirm before we start production

Once the samples are accepted, we lock the specification with you in one confirmation sheet covering:

  • Panel finish code and sheen level, referenced to the sample you approved
  • Glass type and edge treatment for the door, as shown in the sample
  • Frame profile colour and door style
  • Made-to-measure dimensions taken from your site drawings, with clearances for appliances
  • Layout of glass-front doors against closed doors, and the interior configuration behind each one
  • Hardware finish and door opening direction

Because dimensions are project-specific, we ask you to verify site measurements at this stage rather than at delivery. Any change after sign-off restarts panel cutting, so it is worth walking the drawings one more time with your installer before you approve.

Where the glass-front line sits in our PVC range

If you are specifying a full kitchen rather than a single run of display doors, the same sample process applies across the wider custom kitchen cabinet range. Buyers pairing glass-front uppers with solid doors commonly compare these finishes side by side in one pack:

Requesting one combined pack instead of three separate ones is usually faster: all finishes are judged in the same room, on the same day, under the same light.

Getting your pack started

Send us your drawings and the finishes you are considering, tell us which glass type you want to test, and we will prepare the sample pack for the Santerson Glass Front Pvc Cabinet together with any matching solid-door panels. We confirm materials, dimensions and selected specifications in writing against your order before production begins, so what you approve on your site is what arrives in the crate.

Working on a villa, apartment or hotel kitchen run and want a sample pack before committing to production? Contact SANTERSON — send your drawings and finish shortlist and we will quote the pack with your cabinet specification.