A glass-front bookcase looks simple on a drawing. It is a tall box, a shelf grid behind it, and glazed doors in front. The problems appear later — a door that sits out of plane after the unit settles, a shelf that sags under a row of hardbacks, condensation trapped against a mirror-glass panel, or a case that cannot be brought through the stairwell it was designed for.
A buying checklist exists to move those risks into writing, where they are cheap to fix. Below is the checklist we apply when a project specifies Santerson Glass Front Bookshelves as made-to-measure built-in joinery — the same sequence our team works through from site survey to handover.
1. Before the quotation: survey and scope
The first item on the checklist is not a product question at all. It is confirmation that the opening has been measured on site, after plasterboard, screed and floor finishes are in place. Nominal dimensions from a drawing routinely differ from the built opening by enough to change a case size.
- Width, height and depth taken at three points each — top, middle, bottom — with the smallest workable figure recorded.
- Floor levelness across the run, because a tall glass-front case transfers even small out-of-level readings into visible door misalignment.
- Position of skirtings, architraves, cornices, switches, sockets and any recessed lighting that the carcass must clear or be notched around.
- Wall construction behind and beside the opening — stud, masonry, tiled, or a lightweight partition — since this determines the fixing method.
- Whether the unit butts into other joinery in the same room, which fixes the reveal order and which unit is measured first.
Scope should be written down at the same time: number of cases, total linear metres, whether lighting and internal drawers are included, and whether the glazed doors are supplied with the carcass or ordered separately. An unpriced door set discovered after production starts is the most common avoidable variation on this product.
2. Configuration: dimensions, layout, finish
Glass-front bookshelves in this collection are configured per project — made-to-measure sizing, material and finish options, and a layout tailored to the space. The checklist item is making sure each of those three choices is stated explicitly rather than inherited from a catalogue image.
Layout grid
Record shelf heights against what will actually be stored. Reference rows, display objects and boxed files need different clear heights, and fixed shelves are cheaper than adjustable ones but unforgiving. A practical approach is to fix the bottom two shelves for heavy items, keep the eye-level band adjustable, and reserve the top band for items that rarely move.
Shelf span and load
This is where a glass-front unit differs from an open one: once the doors are closed, sagging shelves stay visible through the glass for the life of the project. For each shelf, note the unsupported span, the intended load, and whether a intermediate support or a thicker panel is needed at that span. Confirm the answer in writing with the factory rather than assuming a standard board will carry it.
Carcase material and finish
The carcase material and surface finish are selected per project, so the checklist should name the exact finish reference for every visible surface — including shelf edges, the inside face of doors and any end panel that will be seen in plan. Where a room already contains joinery, request a physical sample against the existing finish instead of approving from a screen.
3. Glass: type, thickness, edge, hardware
The glazing is the item most often left vague in an enquiry and most expensive to change later. Write all five decisions into the specification.
| Decision | What to record on the checklist |
|---|---|
| Glass type | Clear, low-iron, frosted, reeded or tinted — and whether it is specified for display clarity or for obscuring contents. |
| Thickness | The thickness the door system is rated for. Thicker glass needs a matching channel, hinge and gasket set. |
| Edge treatment | Polished or seamed edges, and whether exposed edges are visible from the room. Polished edges matter on frameless and slim-profile doors. |
| Safety requirement | Toughened glass where impact is realistic — family living areas, playrooms, and any commercial or hospitality setting. State this in the order, not at installation. |
| Fitting method | Rabbeted rebate, aluminium channel, silicone gasket or clamp fitting, plus the hinge type and its load rating for a glazed door. |
Also confirm the handle and opening method at this stage. A glass door with an integrated profile handle behaves differently from one with a surface-mounted knob, and the cut-out has to be produced in the factory rather than adapted on site.
4. Doors: geometry, clearance, alignment
- Swing or slide. Sliding doors save the swing arc in a narrow study; hinged doors give full simultaneous access to the shelf grid. Decide from the room's circulation, not from the render.
- Clearance. Check the door against adjacent walls, furniture and handles at its widest open position, and check sliding panels against each other in both closed and open positions.
- Reveal and gap. State the required gap between doors and between door and carcase. A consistent reveal is a manufacturing tolerance, so it must be agreed before production.
- Weight per leaf. Glazed doors are heavy at height. Confirm each leaf's weight against the hinge or track rating, especially on tall doors.
- Adjustability. Note whether hinges allow three-way adjustment after installation. On a run of four or more doors, this is what makes final alignment achievable by the site team.
5. Fixing and interface with the building
A tall glazed unit carries its load through the carcase into the floor and, where required, into the wall. The checklist should record who confirms each of these, because they sit on different trades' scopes.
- Fixing method for the actual wall build-up behind the opening, with anchors specified accordingly.
- Whether the unit is secured to the wall, the floor, or both — and whether a site-built rebate or scribe is needed for out-of-plaster walls.
- Anchor points for any anti-tip restraint. This matters most in homes with children and in hospitality rooms where guests cannot be relied on to secure furniture.
- Interface with lighting: cable routes, transformer access, and whether drivers are reachable after the unit is fixed and glazed.
- Acoustic or fire-separating walls: check before drilling or notching into a rated construction.
6. Logistics and site access
Built-in joinery fails on site most often at the delivery door — literally. Add an access line to the checklist before production is released.
- Largest single component dimension, checked against stair flights, lift doors, corridors and the tightest turn on the route from the vehicle.
- Whether a full-height case ships assembled or knocked-down, and who assembles it if it arrives in parts.
- Packing method for glazed leaves in transit, and the inspection routine on arrival — glazing is the component most likely to arrive damaged, and a claim after installation is hard to substantiate.
- Spare glass: for projects ordering several identical leaves, holding one spare leaf avoids waiting on a single replacement panel.
For cross-border procurement this stage also covers freight mode, packaging and container loading, customs documentation and door-to-door delivery. SANTERSON arranges sea, air and rail freight with the paperwork handled as part of logistics and door-to-door delivery. Confirm Incoterms, duties and the exact delivery point for each project rather than assuming a service level.
7. Quality checkpoints and sign-off
A checklist is only complete when each line has an owner and a moment in the programme. Four checkpoints cover this product:
- Pre-production approval. Signed shop drawing showing dimensions, shelf grid, door geometry, glass type and finish references. Nothing enters production on a verbal change.
- Finish sample sign-off. Physical samples of carcase finish and glass, approved against the room's existing surfaces.
- Pre-shipment inspection. Carcase squareness, door alignment dry-fitted at the factory, glazing condition, and completeness against the packing list.
- Site acceptance. Doors aligned and operating smoothly, glass clean and free of edge chips, unit level and securely fixed, snag list signed before handover.
Recording these four signatures is what separates a project that closes cleanly from one where the same defect travels from the drawing to the installed room.
Ordering through a one-stop supplier
Bookshelves rarely sit alone in a project. When the same joinery package also covers wardrobes, media units and kitchen cabinetry, splitting those lines across several factories multiplies finish references, packing lists and delivery dates — which is where matching becomes difficult to control. Taking them through one one-stop furniture and building materials supplier keeps a single specification, one production schedule and one shipment, with installation and after-sales support under the same scope.
Send us the opening dimensions and the room's finish references
Share measured openings, a shelf-load note and the finishes you need to match. We will return a configuration with glass type, door geometry and fixings specified for your project — then take it through production, packing and delivery as one package.