A linen cabinet looks like a small item on a bill of quantities until it arrives on site two weeks after tiling, does not clear the doorway, and clashes with the joinery every other surface in the bathroom. Buyers who compare these cabinets properly ask about four things: the internal layout before the external look, how the unit is built for a humid room, what the quotation actually includes, and how the cabinet reaches the site and gets installed. This guide walks through each question in the order you will need it.

Start With What Goes Inside, Not What It Looks Like

The word "linen" describes a storage job, not a fixed design. Before comparing finishes, list what has to fit: bath towels in folded stacks, hand towels on rails, spare bedding, toiletries and cleaning products, hair dryers and styling tools, medicines that need to stay out of reach. Each category wants a different depth, shelf height or fixing method.

Then map those items onto the room. A cabinet beside a basin usually needs shallow shelves for folded towels within arm's reach. A cabinet in a hallway off the bathroom does more work with deeper shelving for bedding. Housekeeping pantries and laundry areas need vertical space for long-handled tools and bulk stock, which is why Multi Function Tall Cabinets are often specified there instead of a standard bathroom unit.

  • Towels in stacks need 320–400 mm of shelf height and at least 350 mm depth.
  • Rails for hanging hand towels need clear internal width, not just door width.
  • Small items disappear unless you specify drawers, trays or a shallow intermediate shelf.
  • Cleaning chemicals and medicines may need a lockable compartment or a high closed section.
  • Air vents matter when damp towels or laundry baskets go inside a closed box.

Send this internal list to the supplier along with your dimensions. A quotation that only states a cabinet size tells you nothing about whether the inside will work.

Check How the Cabinet Is Built for a Wet Room

Bathrooms cycle between humid and dry several times a day, and wall tiles push warm water right up to the back of the cabinet. Ask the supplier three questions in writing:

  • What board or substrate is used for the carcass and doors, and how are the edges sealed?
  • How does the unit tolerate steam, splashes and cleaning products over years of use?
  • Which surface finishes are offered, and which ones suit a bathroom rather than a bedroom?

Sealed edges and stable panels matter more than the colour card. Laminate, lacquer, acrylic and veneer all look acceptable in a showroom sample; they behave differently once steam reaches them daily. Request a finished sample of the exact panel and edge detail you are buying, not a generic swatch, and place it in a similar room for a few weeks before signing off.

Hardware is the second weak point. Hinges, drawer slides and handles face the same humidity. Ask what hardware is supplied, whether soft closing is included, and how replacements are ordered if one hinge fails in year three. A cabinet with ordinary bedroom hinges in a steam-heavy bathroom will need attention long before the panels do.

Compare Standard Sizes Against Made-to-Measure

Off-the-shelf heights and widths rarely line up with a tiled wall, a ceiling bulkhead or an existing run of vanity joinery. Linen Cabinets in our Tall Cabinets collection are specified per project, which means height, width, depth, internal layout and finish are set from your drawings rather than chosen from three stock options.

Made-to-measure is not automatically the more expensive choice. It removes filler panels, scribe strips and awkward gaps that add site labour, and it lets a cabinet stop flush with a wall instead of protruding into a circulation route. What it does require is accurate dimensions taken after finishes are complete or clearly noted as finished dimensions on the drawing.

When you compare quotations, put them side by side in one table:

Item to confirmWhy it changes the price and the result
Finished dimensions and toleranceA cabinet that is 10 mm too wide becomes site carpentry, not a delivery.
Carcass material and edge sealingDetermines how the unit survives daily humidity.
Internal layoutAdjustable shelves, drawers, trays and rails each carry different cost.
Door styleHinged, sliding and mirrored fronts need different clearances and hardware.
Fixings and wall conditionTiled and lightweight partition walls need specific anchors and support.
Finish matchingMatching an existing vanity or wardrobe run costs more than a standard colour.

Decide How the Cabinet Fits the Rest of the Project

A single cabinet ordered alone is easy to price and hard to match. When vanities, wardrobes, wall panelling and doors come from different sources, small differences in wood tone, handle style and panel profile become visible in the same sightline. This is where built-in furniture coordinated as one package saves rework later.

Ask whether the supplier can produce the linen cabinet, vanity and wardrobe in one material and finish specification, and request a single drawing set showing all three in position. If you are furnishing a whole villa or apartment floor, coordinating cabinetry with villa and interior fit-out supply also means one party owns the schedule rather than three.

Project buyers should also confirm who signs off the shop drawing, who checks it against the site dimensions, and what happens if a measurement changes after tiling. Getting that sequence agreed in writing is worth more than any discount on the unit itself.

Price the Whole Journey, Not Just the Cabinet

For overseas sourcing, the invoice price is only part of the comparison. Ask each supplier to state:

  • Packaging method and how glass or mirrored fronts are protected.
  • Whether the unit ships flat-packed or assembled, and what that means for on-site assembly time.
  • Freight mode, incoterms and who handles customs clearance.
  • Delivery point: kerbside, room of choice or install-ready.
  • Who installs, who inspects for snags, and how damage in transit is handled.
  • How spare hinges, shelves or a replacement door are ordered later.

Two identical cabinets can differ substantially in landed cost once packaging, freight and installation responsibility are added. Compare quotations on the same basis before choosing the lower headline figure.

Questions to Put to Every Supplier

  • Can you produce a shop drawing with internal layout for our dimensions?
  • Which substrate and edge treatment do you use in bathrooms, and what have you seen fail?
  • What hardware brand and grade is fitted as standard?
  • What is the lead time from approved drawing to dispatch?
  • How are cabinets packed for international freight, and what is covered if one arrives damaged?
  • Can you match an existing finish, and how do you confirm the match before production?

Suppliers who answer these with specifics — materials, tolerances, hardware grades, drawing stages — are usually easier to work with than those who reply with a catalogue page and a price.

Before you order: confirm finished dimensions after tiling, get one approved sample of the panel and edge detail, and hold a single signed shop drawing that shows internal layout, door swing and fixing method. Those three steps prevent most linen cabinet problems on site.

SANTERSON manufactures tall cabinets and custom furniture for residential and hospitality projects, with made-to-measure sizing, material and finish options, and coordinated supply through production, logistics and installation support. Send your room dimensions and internal storage list, and we will return a shop drawing and quotation for review.