A swim spa on a hotel site is not a single line item on a purchase order. It is a piece of plant equipment that touches the structural slab, the electrical distribution, the pool plant room, the water treatment regime and the guest experience programme at the same time. This guide walks through how buyers, contractors and consultants specify Outdoor Swim Spa WS-S12-T on a hospitality project, from early space planning to handover.
Where the 11.7 m footprint belongs in the site plan
The catalogue dimension for WS-S12-T is 11740 × 2200 × 1470 mm. Read that as a long, narrow shell rather than a square plunge pool, and it changes where the unit can realistically sit. On most hotel sites the workable positions are a rear terrace or podium deck, a ground-level garden zone beside the spa suite, or a rooftop setback on a structurally assessed slab. The width is the easy part; the 11.7 m length is what drives the plan.
Before the layout is fixed, confirm three things with the design team:
- A clear delivery route from the site entrance to the final position. A shell of this length needs an unobstructed path, a crane or hiab lift where the deck wraps the building, and a setting-out drawing that accounts for the turning radius.
- Working clearance around the shell for the plant components. The unit carries two water pumps, a filter pump and a control system; access panels must remain reachable for routine servicing, not just at install.
- Deck level and drainage falls relative to the surrounding finish. An in-ground or semi-recessed installation is a structural and waterproofing decision, so it should be resolved during documentation rather than on site.
Reading the specification as an equipment schedule
The published figures for this model are best treated as the starting point of a shop drawing review, not as a finished mechanical schedule. The catalogue lists 73 jets in total, two water pumps, one filter pump, one control system and one swim training set, with LED lighting provided as one fitting plus 50 small LEDs, and a total power figure of 7.65 kW.
| Catalogue item | What to confirm before the order is released |
|---|---|
| Shell 11740 × 2200 × 1470 mm | Final position, support detail, and whether the unit sits above ground, semi-recessed or fully recessed. |
| Jet total: 73 pcs | Jet layout against actual guest circulation, and which zones are hydrotherapy versus seating. |
| Water pump ×2, filter pump ×1 | Switchgear capacity, circuit protection and the distance to the plant room or electrical riser. |
| Total power: 7.65 kW | Supply arrangement, tariff and metering for the operator, plus any heat pump load added on top. |
| Swim training system ×1 set | Whether the programme is counter-current swim only or also hosts aqua-fit sessions, which affects jet zoning. |
| LED lighting, ozone | Disinfection regime required by the local licensing authority for a commercial-occupancy pool. |
The catalogue also lists options such as control systems, UV sterilisation, additional water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so each option needs to be priced and confirmed against the selected configuration rather than assumed from a brochure.
Sequencing the swim spa inside the programme
The most common procurement failure on this category is ordering the shell at the same time as the loose furniture. The spa has to arrive after the slab, waterproofing and drainage are complete, but early enough that the deck finishes can be closed around it. That usually means the shell is a long-lead item locked in during documentation, while the electrical and plant interfaces are fixed at the same time.
A practical sequence looks like this:
- Concept: confirm the spa is wanted as part of the leisure offer, agree the rough footprint and whether it is one unit or a paired arrangement with a separate relaxation pool.
- Documentation: issue setting-out, structural and electrical interfaces; fix the disinfection regime; lock the option list.
- Procurement: release the shell and plant together so the delivery date matches the site window. SANTERSON's Custom & OEM Service covers bespoke material finishes and configuration work where the operator wants the surround, steps and cabinetry matched to the wider joinery package.
- Logistics: agree the delivery mode, container loading plan and site access well before shipment. The Logistics & Door-to-Door Delivery service covers freight forwarding, customs paperwork and door-to-door delivery; Incoterms, duties and insurance should be settled per project.
- Commissioning and handover: fill, balance and test the circuit, then walk the operator through controls, dosing and maintenance. The Installation & After-sales Support service lists on-site installation, snag inspection, warranty coverage, spare parts and ongoing maintenance.
Costing the package properly
Budget the spa as a works package with interfaces, not as a product price. The equipment cost is only part of it: crane set, slab or pedestal preparation, waterproofing upstands, electrical distribution from the switchboard, plant room or equipment cupboard, deck finishes, safety signage and depth markings, and the operator's ongoing energy and chemical consumption all sit around the unit.
Two practical cost levers are worth testing at value-engineering stage. First, insulation and heat pump options change running cost as well as capital cost, so they should be modelled over the operating life rather than priced only on day one. Second, if the leisure offer needs more than one water body, pairing a swim unit with a Long Outdoor Swim Spa with Hydrotherapy & Relaxation Pool or a shorter lounge unit is often cheaper than buying two long shells, because the plant and circulation can be planned around one dominant volume.
What to ask the supplier in the first round of enquiries
- Confirmed dimension and weight for the shipped configuration, plus the lifting and setting-out drawing.
- Electrical requirements stated as supply, circuit and protection, so the M&E consultant can check against available capacity.
- Which items in the option list are compatible with this model, and which change the lead time.
- The water treatment arrangement offered for a commercial-occupancy installation, and what the operator's maintenance regime looks like after handover.
- Delivery terms to site, packaging and container loading plan, and who carries the lifting operation.
Getting those answers in writing during the first enquiry round is what keeps the swim spa off the critical path later. The wider Swimming Pools and Swim Spas range covers alternative lengths and configurations if the site geometry rules this shell out, and the Hospitality Project Furnishing service covers coordinating the spa surround alongside the rest of the furniture and building-materials package.