A compact laundry unit looks like a small item on a fit-out schedule until the first site measurement is taken. Depth conflicts with a doorway, a machine door cannot clear a wall, a drain is not where the drawing assumed it would be — and a unit that was supposed to be built in three weeks goes back to the shop for rework. If you are specifying Compact Laundry Solutions for a residential bathroom or laundry project, most of those problems can be closed out on paper before a single panel is cut. Here is the confirmation list we work through with buyers, designers and contractors before production starts.
1. The room data, not just the unit size
Our laundry units in the Laundry Integration collection are made to measure, so the starting point is the space, not a catalogue dimension. Before we quote, send:
- Clear width, height and depth of the recess or wall run, measured at floor, mid-height and ceiling — older buildings are rarely square.
- Position and height of the waste/drain outlet, water supply points, and any isolating valves.
- Location of the power outlets and whether they sit behind the unit; a machine pushed flush into a recess can lose the socket.
- Door swing, skirting boards, window reveals and anything that reduces usable depth by 20–40 mm.
- Whether the wall is stud, brick or concrete — this decides how the unit is anchored and whether a top panel can be scribed to the ceiling.
For units installed inside a bathroom, also confirm waterproofing boundaries. A cabinet fixed through a membrane is an expensive correction after tiling.
2. Which machines will actually sit in the unit
"Compact" only means something relative to the appliances you intend to buy. Confirm the exact washer and dryer models, or at least their external dimensions and door openings, before we finalise the carcass. We need to know:
- Front-load or top-load. A top-loader needs clearance above it; a front-loader needs clearance in front for the door.
- Stacked or side-by-side. If stacking, Stacked Laundry Units let us design the support and access around that pair rather than adapting a standard box.
- Ventilated or heat-pump dryer. A vented machine needs a duct route; a heat-pump unit needs a place for condensate and far more forgiving clearances.
- Total weight when loaded, which affects shelf and bracket specification in tall joinery.
3. Moisture exposure and material choice
Laundry cavities inside bathrooms get wet — splashing, steam from daily showers, occasional overflow. Tell us the room type and we will match the board and finish to it rather than defaulting to a bedroom-grade specification. For a shared family bathroom or a serviced apartment where the unit is used daily, we specify moisture-resistant substrates and edge sealing; for a guest-level powder room with a small machine, a lighter specification is fine and cheaper.
Confirm the finish at the same time: Matte Acrylic Cabinets, melamine, lacquer or wood veneer are all available. If the unit must read as continuous with the kitchen or wardrobe run, send us the door profile and colour reference used elsewhere in the project so we match grain direction and sheen instead of approximating it.
4. Storage layout and access
The machines take up most of the volume, so the remaining storage has to be planned deliberately. Decide before production:
- Detergents, powders and cleaning chemicals — closed drawers or doors if children are in the building.
- Baskets: fixed shelves, pull-out rails, or dedicated Pull Out Laundry Hampers built into the base.
- Ironing, hanging and folding: whether a pull-out board, a hanging rail or a fold-down door surface is required.
- Whether the unit also stores linen, in which case Laundry & Storage Combo configurations let one run carry both functions.
5. Interface details that are cheap on paper and costly on site
| Item to confirm | Why it matters before production |
|---|---|
| Countertop or no countertop, and its material | Determines whether the carcass is a closed unit or an open frame, and where the cut-out for the machine sits. |
| Hinge side and door opening sequence | A door that fouls the machine door or the room entry has to be rebuilt, not adjusted. |
| Handleless profile, handle, or push-open | Handle projection can consume the last few millimetres of a tight recess. |
| Integrated lighting or sensor light | Needs a power feed and a driver position decided during fabrication. |
| Plinth, adjustable feet, or wall-hung | Affects cleaning access, moisture clearance at floor level and load path. |
| Access panel for valves and pump | Serviceability after tiling; a sealed box with no access creates a demolition job later. |
6. Documentation, tolerances and sign-off
We produce shop drawings for your review before manufacturing. Ask for dimensioned elevations, the appliance cut-out positions, service clearances and the finish schedule, then have the site team check those numbers against the as-built space — not against the architectural drawing alone. Where a project has several identical units, confirm one prototype or first-article unit and sign it off in writing before the remaining sets are released.
Also fix the tolerance you will accept on-site: scribing to uneven walls, shadow gaps between the unit and tiled surfaces, and whether an installer fills and trims on site or the joinery arrives finished. That single decision changes both the price and who is responsible for the last 5 mm.
7. Delivery, packaging and installation responsibility
For projects outside China, tell us the delivery address and the Incoterms you are working to, so we can package and load the units for the freight mode you have chosen — sea, air or rail — with flat-packed or assembled options as the site access allows. Confirm who installs: our team provides on-site installation support and inspection, but if a local contractor is doing it, we should agree the fixing method and the anchoring detail in advance so responsibilities are clear at handover.
Quick pre-production checklist
- As-built room measurements taken at three heights, with photos of services.
- Appliance make, model and external dimensions confirmed in writing.
- Ventilation route or condensate path decided.
- Material and finish matched to moisture exposure and to adjacent joinery.
- Storage layout agreed (drawers, hampers, hanging, folding surface).
- Shop drawings reviewed and signed by the site team, not just the designer.
- Delivery terms, packaging method and installer identified before manufacture.
FAQ
Can a compact laundry unit be built into an existing bathroom without retiling?
Sometimes. Where the waste and supply are already in a workable position, we design the carcass around the existing services and scribe to the finished tile line. If the drain is in the wrong place for the machine you have chosen, moving it is a plumbing decision that has to happen before joinery is finalised.
What if I do not know the appliance model yet?
Send us two or three candidate models and we will design to the largest set of dimensions, or leave the cut-out generous with an adjustable support. It works, but it costs more in material and usually gives up storage depth, so confirming early is worth it.
Can the laundry unit match my kitchen cabinetry?
Yes — same board supplier range, same door profiles, same veneer or lacquer specification. Send the reference from your Kitchen Cabinets and Hotel Appliances selection and we will build the laundry run to match.