Integrated lighting inside cabinets, shelving and wardrobes looks simple on a rendering and complicated on site. Cables run to the wrong side, drivers have nowhere to sit, finishes do not match the joinery, and the electrical specification arrives after the cabinet carcass is already in production. A procurement brief that treats Santerson Integrated Cabinet Lighting as a specified product rather than an afterthought removes most of those problems before the order is placed.

This guide sets out what to write into the brief, which questions the manufacturer needs answered, and how lighting sits alongside the rest of the fit-out when cabinets, joinery and fixtures come from one supplier.

Why integrated cabinet lighting needs its own line item

Surface-mounted luminaires can be decided late. Recessed strip lighting inside a carcass cannot: the profile, the route for the cable, the position of the driver and the method of fixing are all built into the panel. If the brief only says "LED lighting to cabinets", the factory builds to its own default and the site team discovers the mismatch at handover.

Santerson's catalogue lists integrated cabinet lighting within the Lighting & Accessories collection, for residential bathroom projects, with finish, layout and dimensions specified per space. The same configurable approach appears across related lines: Santerson Integrated Lighting Systems integrates lighting into modular shelving, where layout, dimensions, material and finish are set for the project, and the Santerson LED Mirror Cabinet is configured with lighting and electrical details confirmed per project. In each case the product page asks that electrical specifications and compatibility be confirmed for the chosen cabinet design — which is exactly what a good brief does.

The six items to state in the brief

ItemWhat to writeWhy it matters
Location and unit typeWhich cabinet, niche, shelf or wardrobe each lighting run sits in; room by room scheduleDetermines the carcass detail, not just the fitting
Layout and dimensionsRun lengths per unit, positions of recessed profiles, which shelves are litProfile length and cable route are cut into the panel
Finish and appearanceColour or finish matched to the joinery; diffuser style; whether the source is visibleAvoids a mismatch between lighting trim and door fronts
Switching and controlDoor-activated, motion sensor, touch or wall switch; where the control sitsSensor placement must be clear of obstructions and doors
Electrical specificationVoltage, driver type, load per run, driver location, access for serviceDrivers need a reachable position inside or behind the unit
Compatibility confirmationWritten confirmation that the lighting matches the specific cabinet designPrevents generic defaults being applied to custom joinery

Schedule by room, not by product family

A single list of lighting SKUs is harder to price and harder to install than a room schedule. For a bathroom package, list the vanity, the mirror cabinet, any niche or open shelf, and the wardrobe separately, with dimensions and finish for each. The same method works for kitchens and living areas, where integrated lighting is specified together with custom built-in kitchen cabinets supplied as interior fixtures for hotel, apartment and residential projects, with cabinet layout, sizes, door styles and surface finishes customised per project.

Specify the lighting together with the joinery

When cabinets, wardrobes, shelving systems and their lighting come from separate suppliers, the interface is where cost appears: who cuts the profile groove, who supplies the driver, who is responsible if a run fails. Santerson's one-stop scope covers furniture and building materials with custom and OEM service — custom design and prototyping, bespoke finishes and textures, material choices including wood, metals, engineered stone and laminates — so lighting can be coordinated with the carcass it is built into rather than retrofitted to it.

For projects that also need display or storage walls, specify integrated lighting systems at the same time as the modular shelving layout. Layout, dimensions, material and finish are set for the project, so the lighting runs become part of the panel schedule instead of a variation order later.

What to ask the manufacturer to confirm in writing

  • The electrical specification and compatibility of the chosen lighting with each cabinet design on the drawing set
  • Driver type, location and how it is accessed for maintenance
  • Whether the profile is recessed, surface-mounted or concealed, and which panel it is fixed to
  • Finish and diffuser sample matched to the approved joinery finish
  • Switching or sensing method, and where the sensor sits relative to doors and shelves
  • Spares quantity for strip, driver and control, ordered with the package

Practical note. Product pages for these lines state that dimensions, finishes, electrical ratings and installation requirements are to be confirmed for each configuration. Treat those as open items in the brief until the manufacturer's technical confirmation is on file — do not carry catalogue wording into a contract document as if it were a tested rating.

Fitting lighting into the wider procurement timeline

Santerson describes its project workflow as consultation, design and planning, production, logistics, installation and after-sales, with door-to-door freight and on-site support listed among the services. Lighting specification belongs in the design and planning stage, before production begins, because the panel detail is fixed at that point.

A practical sequence for a fit-out package:

  • Brief stage — room schedule of lit units, with dimensions, finish and switching intent
  • Design and planning — profile positions, cable routes and driver locations drawn onto the cabinet elevations; technical confirmation requested
  • Production — carcasses built with the lighting detail included; sample finish approved before bulk
  • Logistics — lighting packed with its matching unit and labelled to the room schedule, so installers are not sorting components on site
  • Installation and handover — each run tested against the schedule; spares handed over with the as-built list

Common brief failures and how to avoid them

Generic wording. "LED strip to all cabinets" gives the factory nothing to price against. replace it with a per-unit schedule.

No driver location. Drivers fail before strips do. If no accessible position is drawn, access means removing a panel after handover.

Finish decided late. A diffuser or trim that does not match the approved door front is visible every day of the building's life. Approve the finish with the joinery sample.

Sensor behind a door. Motion sensing specified without checking the swing of the door produces lights that never trigger.

No spares. Strip and driver are consumables in a hotel or rental package. Order them with the original batch so the finish and output match.

FAQ

Can integrated cabinet lighting be added after the cabinets are made?

Recessed profiles, cable routes and driver positions are built into the panel, so late additions mean site modification. Specify during design and planning, before production.

Is the electrical specification fixed by the catalogue?

No. The product pages state that electrical specifications and compatibility must be confirmed for each cabinet design, so obtain written confirmation for your configuration.

Should lighting be ordered with the cabinets or separately?

Order it with the joinery package. The same supplier then owns the panel detail, the finish match and the packing list, which keeps responsibility for the interface in one place.

Does the same approach apply to shelving and mirror cabinets?

Yes. Integrated lighting systems in modular shelving and LED mirror cabinets are both configured per project, with dimensions, finish and electrical details confirmed for each installation.

Send us your lighting schedule. Share the room-by-room list of lit cabinets, niches and shelving, with dimensions and finishes, and our team will confirm the configuration for each unit before production. Contact SANTERSON — PHILLIP, +86-13928214007, https://www.santerson.com/contact/.