A matte veneer wardrobe looks simple on a drawing: a flat door, a soft grain, a quiet colour. It is one of the least forgiving items in a joinery package to put into production, because there is nowhere for the surface to hide. Before we cut a single panel for a villa or apartment bedroom, these are the points we settle with the buyer, designer or contractor.

1. The veneer itself: species, cut and how the grain will be laid out

Veneer is a thin slice of real wood over an engineered substrate, so two doors from the same species can look completely different depending on how the sheet was cut and how the leaves were assembled. Before production we need the buyer to confirm:

  • Species and figure. Whether the drawing calls for a plain-cut or quarter-cut face, and whether flame, ribbon or straight figure is wanted. Our Walnut Veneer Wardrobes and Natural Oak Veneer Wardrobes are separate specifications, not one item with a colour change.
  • Cutting sequence. Book-match, slip-match or reverse-match. A book-matched pair reads as one symmetrical image across two doors; a slip-match repeats the same grain line up each door. This has to be decided on elevation drawings before the leaves are laid up, because it cannot be changed later.
  • Which face is visible. On a return panel or a door edge that shows at a corner, we need to know whether the client expects continuous grain or an acceptable butt joint.

Where a bedroom scheme continues onto walls or a dressing room, we usually recommend specifying the Wood Veneer Panels at the same time and from the same log batch, so the wardrobe and the wall cladding age to a similar tone rather than sitting side by side as two different browns.

2. What "matte" actually means on this job

Matte is not one finish. It is a family, and the difference between samples is easy to lose in an email photograph. We ask for three things in writing:

  • Gloss level. A flat, open-pore surface that lets the grain read as wood, or a low-sheen closed surface that feels smoother under the hand. Both are sold as "matte".
  • Coating system and reference sample. The buyer approves a physical sample panel, not a screen value. We match to that panel for the whole order.
  • Repair and cleaning expectation. Matte surfaces show handling marks differently from gloss, and the cleaning method should be agreed before handover notes are written for the site team.

The same logic applies to High Gloss Veneer Wardrobes: if a project mixes matte doors with a gloss drawer front or a glossy tall unit, both finishes should be approved together on one sample board so the contrast is intentional.

3. The substrate and construction behind the face

A veneer door is only as stable as the board under it. For a full-height wardrobe in a bedroom that runs warm in summer and cool in winter, we confirm with the buyer:

  • The core construction for doors, carcass and shelves, and whether any tall single-leaf door needs a specific construction to stay flat.
  • Edge treatment: veneer-wrapped edge or solid timber lipping, and which one is acceptable where the edge catches light.
  • Back panel thickness and how it is fixed, since this affects how square the carcass stays once loaded with hanging clothes.

We do not publish a single "standard" spec for this range. Our Matte Finish Veneer Wardrobes are made to measure, and the material and finish options are set per project, so the construction is confirmed against the drawings rather than selected from a catalogue line.

4. Dimensions that must come from site, not from the drawing package

Most wardrobe rework traces back to dimensions taken off an architectural drawing instead of the finished room. Before release to production we want:

Item to confirmWhy it changes the build
Floor and ceiling finish levelsBuilt-in wardrobes are dimensioned to the finished surface; a 15 mm change in screed or skirting changes every carcass height.
Wall plumb and squareOut-of-plumb walls are taken up by scribing, not by forcing the carcass. We need to know whether a shadow gap or a scribed trim is wanted.
Door swing and clearanceHinged doors need clearance from handles and adjacent returns; sliding doors need track depth built into the plan.
Services behind and aboveAC lines, downlights, sprinkler heads and switch plates all sit in the zone a wardrobe occupies.

5. Interior layout and hardware

The exterior is what the designer signs off; the interior is what the client lives with. We ask for a signed interior layout covering hanging heights, drawer positions, shelf spans and any lighting or power inside the carcass. Hardware choices — hinge brand and opening angle, slide type and load, handles or integrated pulls — are confirmed at the same time, because they determine door thickness, reveal sizes and the cut-outs we machine in the factory.

Where a bedroom wall carries a concealed door next to the wardrobe run, specify it with the joinery. A Santerson Decorative Concealed Door veneered to match the wardrobe face is a different order detail from a door supplied by the builder, and matching them late in the programme is how tone mismatches happen.

6. Finish approvals, packaging and the delivery sequence

For an overseas project the practical checkpoints are:

  • A signed sample panel for veneer species, cutting sequence and matte coating level, kept as the production reference.
  • Shop drawings with every elevation numbered, so the site team knows which carcass goes where.
  • Packaging that separates doors from carcasses and marks each door's position, since doors travel best flat and are the parts most easily damaged on site.
  • A delivery window that lands after the room is sealed, painted and floored. Veneer joinery stored in an open, damp building is where problems start.

If a project needs more than the wardrobe — wall panelling, a vanity, doors and matching tall units in the same veneer — it is worth placing them on one production schedule. Same batch, same log, same coating line, one delivery.

A short pre-production checklist

  • Veneer species, cut and figure approved on a physical sample
  • Cutting sequence fixed on numbered elevations (book / slip / reverse match)
  • Matte gloss level and coating system agreed against the signed panel
  • Substrate, edge treatment and door construction confirmed for the site conditions
  • Site-verified dimensions to finished floor and ceiling levels
  • Interior layout, hardware and any internal lighting or power signed off
  • Matching panelling and concealed doors ordered from the same batch
  • Pack marking, delivery sequence and storage conditions agreed with the site team

SANTERSON has manufactured furniture and building materials for villa, apartment and hospitality projects since 2008. Our Matte Finish Veneer Wardrobes are made to the dimensions, layout and finish selected for each project, and we work from your drawings and site measurements rather than a fixed size range. Send us the elevation drawing, the room dimensions and the finish reference you want matched, and we will come back with shop drawings and a production schedule.

Planning veneer joinery for a villa or apartment project? Talk to our project team about made-to-measure wardrobes, wall panelling and matching interior fixtures.