A ten-metre swim spa is not a product you can judge from a photograph. Before an Australian buyer commits a deposit on the Outdoor Swim Spa WS-S10, there are about a dozen questions that decide whether the finished installation works on the site — or sits half-installed behind a temporary fence for months. This article sets out what to verify, and where each answer should come from.
Start With the Site, Not the Specification Sheet
The WS-S10 is catalogued at 10000 × 2200 × 1420 mm. Read that as a footprint question first: how the shell reaches the ground, what sits under it, and how much clear access the delivery route allows. A ten-metre module through a suburban side street in Sydney or a villa lane in Perth raises access questions that never appear on a product page.
Before requesting a quotation, confirm three site facts in writing: the prepared base dimensions and load path, the clearance from boundary and neighboring structures, and where power will be drawn from. Those three items drive almost every downstream cost — crane or forklift time, electrical work, and any screening required by the local council.
What the Published Specification Actually Covers
The catalog entry for this model lists a control system (1 set), 2 water pumps, 1 filter pump, 76 jets in total, one main LED light plus 40 small LED lights, and total power of 7.65 kW, with water jets, LED lighting and ozone shown as the highlighted features. Treat that list as a starting configuration rather than a delivered scope.
| Catalog dimensions | 10000 × 2200 × 1420 mm |
| Water pump | 2 pcs |
| Filter pump | 1 pc |
| Jet total | 76 pcs |
| Lighting | 1 LED light; 40 small LED lights |
| Total power | 7.65 kW |
| Highlighted features | Water jets, LED lighting, Ozone |
Two specification fields deserve particular care. The captured specification for this model does not list a swim training system, so if the brief calls for counter-current swimming rather than hydrotherapy jet use, ask explicitly which item provides it and on which side of the shell. And because total power is stated as an aggregate figure, request the per-circuit breakdown before any electrical design is signed off.
Confirm Included Equipment Against the Order, Not the Catalog
The catalog lists control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps as options. Availability and compatibility vary by model. For an Australian installation this matters more than it would in a milder market: a heat pump and adequate insulation determine whether the spa is usable through a Victorian winter or only through a Queensland summer, and they change running load substantially.
- Ask for a line-item bill of materials for the exact configuration, with model names for pumps, ozone and any optional sterilisation.
- Ask which items are fitted at the factory and which arrive loose for site installation.
- Ask what is excluded — base, steps, handrails, electrical supply and controls on the load side are common gaps.
Electrical Requirements Are the Most Common Failure Point
With a stated total power of 7.65 kW plus optional heat pump, the supply question is not academic. Ask the supplier for the electrical schedule for the selected configuration: supply voltage and phase, full-load current, circuit protection, dedicated vs shared circuits, and the location of the isolator. Then have an Australian-licensed electrical contractor confirm that schedule against local wiring rules before the base is poured. Getting this sequence wrong means cutting into fresh concrete.
Similarly, ask how the control system is operated and where it is mounted, whether the manufacturer supports commissioning remotely or on site, and what documentation ships with the unit — wiring diagram, parts list and warranty terms in writing.
Compare Within the Range Before Committing to One Model
SANTERSON's Swimming Pools and Swim Spas category covers a wide spread of sizes, so the ten-metre shell is one option rather than the only one. The Outdoor Swim Spa WS-S12, for example, is catalogued at 11740 × 2200 × 1470 mm with 73 jets, 50 small LED lights and the same stated total power of 7.65 kW — a longer shell on a similar electrical load. Where the site will not accommodate ten metres, or where a shorter shell leaves room for circulation and planting, that comparison changes the whole layout.
Where the space is irregular or the design calls for a specific geometry, the Customizable Shape Outdoor Spa covers square, round, oval and curved configurations with an acrylic shell and structural reinforcement, for gardens, terraces and leisure areas. Custom shape means a different drawing and approval path, so allow for it in the programme.
Who Coordinates the Rest of the Package
A swim spa rarely arrives alone. Poolside loungers, shading, paving, screening and lighting usually travel on the same project, and splitting them across suppliers is where coordination costs creep in. SANTERSON positions itself as a One-stop Furniture and Building Materials Supplier, covering design consultation and space planning, material selection and product specification, manufacturing and quality control, project management with site coordination, and final installation and handover.
For freight, the Logistics and Door-to-door Delivery service describes sea, air and rail forwarding, customs paperwork, packaging and container loading, shipment tracking and door-to-door delivery. For an Australian buyer, agree the Incoterms, who acts as importer of record, and who handles final-site delivery beyond the kerb — a ten-metre shell landing at a port is not the same as it landing on a prepared base. Post-delivery, the Installation and After-sales Support service covers on-site installation, inspection and snags, warranty coverage, spare parts and ongoing maintenance; ask which of those apply to a swim spa specifically, since mechanical commissioning differs from furniture assembly.
Use the Australian Project Record for Context, Not as a Guarantee
The company's Australian Villa Furniture Projects record includes villas in Willoughby, North Turramurra, Perth, Melbourne and Sydney, which is useful evidence that the supplier has shipped into Australian conditions and coordinated with local trades. It is not evidence about this product. Nothing in those references establishes pool compliance, certification or delivery performance for a swim spa, and none should be read as a promise on your project.
Approval and Compliance Questions to Put to Your Own Team
Pool and spa regulation in Australia is state- and territory-based, and requirements around barriers, gate hardware, signage and depth vary. That work sits with the buyer's local building surveyor, pool safety inspector or certifier — not with an overseas manufacturer, and it should not be assumed from marketing material. Put the shell dimensions, finished water level and intended siting to your certifier early, alongside the fence and gate detail, so approval runs in parallel with manufacturing rather than after it.
A Verification Checklist Before the Deposit
- Confirmed configuration list — pumps, jets, control system, lighting, ozone, and any heat pump, insulation, UV or sand filtration added.
- Written answer on whether a swim training system is included for this model.
- Electrical schedule: voltage, phase, full-load current, circuit protection, isolator location.
- Delivery route survey and lifting plan for a 10 m shell to the prepared base.
- Agreed Incoterms, importer of record, and who delivers beyond the kerb.
- Certifier's position on barrier, gate and approval requirements for the chosen siting.
- Warranty terms in writing, plus spare-parts availability and who commissions the plant.
Sourcing a ten-metre swim spa from overseas is entirely workable when those seven items are closed out before the order. The buyers who run into trouble are not the ones who compared jet counts — they are the ones who discovered the electrical schedule, the lifting plan and the certifier's questions after production had already started.
Send Us Your Site Drawings First
Before requesting a price for the WS-S10 or another model in the range, send the site plan, the intended siting and your electrical constraints. We will confirm what is included in the configuration and what stays with your local trades.
SANTERSON — furniture and building materials for villa, hospitality and office projects. Enquiries: Contact Us.