A shaker panel wardrobe is one of the easiest built-in pieces to specify on paper and one of the easiest to get wrong on site. The profile is simple — a flat centre panel framed by a square or rectangular border — so there is nowhere for a bad dimension, an unfinished reveal or a clashing shadow gap to hide. When the drawing set, the site conditions and the production details do not agree with each other, the result is the same on every project: the unit arrives, and it does not fit the opening, the doors bind, or the panel proportions look wrong against the skirting and ceiling line.
This guide walks through how our team coordinates a made-to-measure wardrobe with design drawings and real site conditions — what we need from your drawing set, which site dimensions decide the build, where finish and hardware choices interact with the drawings, and how the same sequence applies whether you are furnishing a single villa bedroom or a run of guest rooms.
What a shaker panel wardrobe is
In our catalogue, the shaker panel wardrobe sits in the Classic Paneled Wardrobes collection. The defining feature is the door: a centre panel surrounded by a frame of even width, with clean square corners and no moulding detail beyond the frame itself. It reads as classic joinery without being ornate, which is why it appears so often in villa bedrooms, serviced apartments and hotel guest rooms that need a traditional feel but a modern fit-out.
Because the style is defined by proportion rather than decoration, three drawing decisions do most of the visual work:
- Frame width — the width of the border around each door panel. A narrow frame reads contemporary; a wider frame reads traditional. The same wardrobe carcass can look like two different products depending on this one dimension.
- Panel set-back and edge profile — how deep the centre panel sits relative to the frame, and whether its edges are square or softly eased.
- Door-to-door and door-to-wall gaps — the shadow lines between doors, and between the outermost doors and the reveal. These gaps have to be consistent across the whole run, and they depend on how the unit is packed into the opening.
Related collections in the same family follow the same coordination logic if you want to mix door styles across a project: Raised Panel Wardrobes for a more moulded, traditional look, and Paneled Hinged Wardrobes where the panel detail is paired with a hinged opening.
What we need from your design drawings
The drawing set does not have to be complete before you enquire — many projects start with a concept image and a floor plan. But before production is released, four sets of information need to exist in some form, and each one removes a different category of site problem.
1. Room setting, not just a wardrobe elevation
A single wardrobe elevation tells us the unit size but not how it meets the room. We work best with drawings that show the wardrobe in context: floor finish build-up and threshold details, skirting or architrave treatment, ceiling line and cornice, the adjacent door opening, and any window reveal within reach of the unit. Those elements decide whether the carcass is scribed, whether a filler panel is required, and how the outer stile finishes against plaster.
2. Interior layout with storage intent
The internal layout should be drawn to how the space is actually used — long hanging for dresses and coats, double hanging for shirts, drawer banks for folded items, shelves for linens, plus provisions for a safe, luggage or lighting. If you are specifying for a hotel or serviced apartment group, tell us the guest profile: business travellers and families need different internal splits even when the carcass size is identical.
3. Materials, finishes and sample reference
Our configurable wardrobe listings state made-to-measure sizing, material and finish options, and a layout tailored to the project — they do not fix a single board specification or colour. For that reason we ask for a named finish reference, or a physical sample and target colour, rather than accepting a descriptive phrase on a drawing. A lacquer, a laminated board and a veneer can all be specified as "white", and each behaves differently under the same lighting over time.
4. Door construction and opening method
Hinged or sliding? The answer changes the carcass depth, the clearance needed in front of the unit, and how the unit relates to carpet and thresholds. Sliding layouts need track allowance and level floors; hinged layouts need swing clearance and consistent hinge positions. If your drawings show a run that turns a corner or wraps around a structural column, flag it early — those transitions are drawn differently for each method.
Site requirements: the dimensions that decide the build
Drawings describe intent. Site conditions describe reality. A made-to-measure wardrobe is only as accurate as the dimensional data behind it, so we work from a verified site survey rather than architectural dimensions alone.
| Site item to verify | Why it matters |
|---|---|
| Floor-to-ceiling height at several points across the opening | Slabs and ceilings vary. Measuring at three or more points tells us whether the unit needs scribing or a filler, and prevents an ordered unit that is a few millimetres too tall. |
| Out-of-plumb walls and out-of-square corners | Affected by older buildings and renovated rooms. Determines which side of the carcass carries the scribe and whether corner units need a compensating panel. |
| Floor finish build-up and threshold levels | Tiles, screed, carpet and underlay change the finished floor level. Sliding tracks and hinged door clearances depend on the final level, not the slab. |
| Positions of switches, sockets and services inside the opening | Anything fixed inside the opening must be shown on the survey or relocated before production; it cannot be moved after the unit is packed. |
| Access route from the delivery point to the room | Lift sizes, stair widths, corridor turns and door widths decide whether a full-height side panel can go in one piece or must be built in sections on site. |
| Lighting provisions and power points | Integrated interior lighting needs wiring run at first fix. Confirm electrical specifications and compatibility with the cabinet design before walls are closed. |
If your project is outside China, send the survey data as a marked-up plan plus photographs of each opening, including corners, ceiling line and floor edge. Where local trades carry out the survey, we review that information with your site team before releasing production drawings.
The coordination sequence we follow
For built-in wardrobes, the consultation-to-installation workflow described on our service pages breaks down into a short, checkable sequence.
Step 1 — Brief and drawing review
We read your drawing set against the product family and flag anything that affects fit or how the unit is built: non-standard depths, full-height panels, curved or raked sections, integrated lighting, mixed door styles in one run.
Step 2 — Site survey data and dimensional sign-off
Survey figures are reconciled against the architectural dimensions. Any difference larger than the scribing allowance is resolved with your site team before drawings are issued for approval, not after.
Step 3 — Production drawings for approval
You receive marked-up elevations showing overall sizes, frame widths, internal layout, door gaps, hinge or track positions and finish references. Written approval at this stage is what locks the order.
Step 4 — Sample and finish confirmation
Board, colour and door profile are confirmed against an approved sample. This is also where handle or handleless detailing is settled, since a routed pull changes the panel edge.
Step 5 — Production and packing for the access route
Panels are machined to the approved drawings and packed to suit the access route recorded at survey stage, with components labelled to a room-by-room schedule so each part is easy to place on site.
Step 6 — Site coordination, installation and snag list
Our service scope covers site coordination, on-site installation and inspection with a snag list. For built-in joinery we agree in advance which trades complete the surrounding works — plaster, paint, flooring, electrical — so the unit is fitted into an opening that is already finished rather than one still being changed around it.
Where drawings and site conditions usually clash
Most wardrobe rework traces back to a small number of coordination gaps. Each has a cheap fix at drawing stage and an expensive one after delivery.
- Finished floor level not fixed. Carpet or tile decided after the order changes door clearance. Fix: record the finish build-up on the survey and confirm the finished floor level before production is released.
- Ceiling cornice left out of the elevation. The unit is drawn to a bare ceiling line while the room has cornice. Fix: show cornice and skirting on the setting-out drawing, and decide whether the wardrobe stops below them or runs through them.
- Door swing conflicts with an adjacent bed, door or wall. Fix: overlay the furniture layout and door swing arcs before choosing hinged doors; switch to sliding where clearance is short.
- Lighting specified late. Interior lighting added after first-fix electrics are complete means exposed conduit. Fix: show interior lighting on the electrical drawing at first fix.
- Mixed collections in one run with inconsistent frame widths. Fix: standardise frame width and shadow gaps across every wardrobe type used in the same room or floor.
- Access route never checked. Full-height panels that cannot reach the room. Fix: record lift, stair and corridor dimensions in the survey and split panels where needed.
How the same process scales across a project
For a single villa bedroom, the sequence above is usually two drawing cycles: review, then approval. For an apartment or hotel group, the practical difference is repetition management — one approved wardrobe type signed off, then every room of that type surveyed against the same reference dimensions so that panels, doors and hardware are interchangeable across units.
This is where working with a supplier that handles both built-in furniture and the surrounding finishes makes coordination simpler. Wardrobes, closet sliding panels, interior doors, wall panelling, flooring and lighting are usually split across several suppliers on a fit-out, and the interface details — where a wardrobe stile meets a door reveal, where a panel run meets a floor threshold — fall between contracts. Coordinating them against one drawing set closes that gap.
Our interior design services cover space planning, furniture layouts and 3D renderings, along with project design coordination covering drawings, production coordination and on-site guidance. Our custom and OEM service covers bespoke finishes and prototyping where a project needs a shaker profile drawn to its own detail rather than a catalogue one.
A pre-order checklist
Before releasing a wardrobe order, confirm each line below in writing. Anything left open at this stage becomes a site variation later.
- Verified survey dimensions for every opening, taken after the finished floor level is fixed
- Approved production elevations with overall sizes, frame widths and internal layout
- Named finish reference or approved physical sample for doors, carcass edges and interior surfaces
- Door method (hinged or sliding), door count, and agreed shadow-gap dimensions across the run
- Hardware selection and whether handleless routed edges are required
- Interior lighting schedule with electrical provisions shown at first fix
- Scribing, filler and cornice strategy for each opening
- Delivery access route confirmed, with panel sizes checked against lifts, stairs and doorways
- Trade interface list: who completes plaster, paint, flooring and electrical around the unit, and by when
The wardrobe style is rarely the hard part. The hard part is agreeing — before production — what the room will look like when it is finished, and making sure the drawing set says so.
Send us your drawings and site data
Share your floor plan, elevations and survey measurements for a shaker panel wardrobe or a full built-in package, and we will return marked-up production drawings, a finish specification and an itemised quotation. We work on villa, hospitality and office projects, with door-to-door delivery and installation support included in our service scope.
Phone / WhatsApp: +86-13928214007 (PHILLIP) · Email: santerson@qq.com