A wall-mounted sideboard looks simple on a drawing: a floating cabinet, a stretch of counter, some open shelving above it. In production it is one of the less forgiving items in a joinery package, because everything that carries load, spans an opening or sits against a finished wall has to be resolved before the panels are cut. The Santerson Wall Mounted Sideboards line is supplied as made-to-measure work, with finish, layout and dimensions specified per project. That flexibility is the point of the product, and it is also why the confirmation stage matters more than the design stage.

If you are a builder, developer or procurement lead placing this item for a villa or residential interior, the following checklist covers what should be locked down before production starts.

Start With the Wall, Not the Cabinet

A floor-standing sideboard carries its own weight. A wall-mounted unit transfers everything — cabinet carcass, stone counter, glassware, appliances — into the wall behind it. Before any dimension is signed off, confirm what that wall actually is.

  • Substrate and fixing route. Solid masonry, timber studs, steel framing and lightweight partition boards each need a different fixing detail and a different blocker or backing frame behind the finish lining. Ask for the wall build-up to be shown on the drawing, not just the cabinet elevation.
  • Span and support points. Long floating runs need intermediate support. Where the unit crosses a stud line that does not match the fixing centres, a continuous backing batten is usually the answer — but it has to be drawn in before lining boards go up.
  • Squareness of the opening. Made-to-measure cabinetry can absorb small out-of-tolerance walls through scribing and packers, but only if the tolerance is measured on site and recorded. Site-verified dimensions beat drawing dimensions every time, and this is worth stating explicitly in your purchase order.
  • Finished floor and ceiling levels. The floating height of the unit is normally set from the finished floor. If floor finishes are still being decided, the elevation cannot be finalised.

Fix the Dimensions That Change Price

Made-to-measure pricing moves with a small number of dimensions, and these should appear as numbers on an approved drawing rather than as a range in an email.

  • Overall width, height and depth, with depth stated as carcass depth plus counter overhang, since the counter projection changes both the appearance and the support requirement.
  • Counter and splashback profile. Where a stone or marble surface sits on the unit, its thickness, edge detail and upstand need to be specified together with the carcass, because the top rail of the cabinet is designed around that load.
  • Open versus closed ratio. Open display niches, floating shelves and fully enclosed sections are built and finished differently. Decide which parts of the composition stay open before the carcass is detailed.
  • Aperture sizes for anything built in. Wine fridges, coffee machines and drawer banks each need their own clear opening, ventilation route and access path.

Documentation to have approved before production release

  • Site-verified dimensions, signed and dated, with the surveyor named
  • Elevation and section drawings showing fixing line, backing frame and counter edge
  • Interior layout schedule: shelves, drawers, open niches, appliance voids
  • Finish schedule with physical samples approved for doors, carcass edges and internal lining
  • Electrical and lighting points marked on the drawing, not added later on site

Confirm the Finish Schedule Physically

The catalogue presents these units with material and finish options rather than a fixed specification. Two finishes that look identical on a screen can behave very differently once they wrap an edge, sit under a light fitting or take fingerprints in a hallway.

Request physical samples of the door face, the matching edge treatment and the internal carcass lining, and view them against the actual wall and floor finishes at site light levels. Where the sideboard is meant to read as one continuous surface with adjacent panelling or wood veneer panels, order the samples for all of those items together so the grain direction, sheen level and tone can be compared side by side. If the scheme also calls for veneered kitchen work — matte wood veneer cabinets, for example — check those samples against the sideboard before either is released.

Also confirm how the finish is specified on the order: by material name, by colour or code reference, and by sheen. A description such as "matte oak" is not an approval document; a sample reference is.

Decide Services Before the Carcass Is Cut

The detail that most often turns into a site variation is not joinery at all — it is the electricity and the plumbing behind the joinery.

  • Integrated lighting. If integrated cabinet lighting is intended for open shelves or niches, the cable routes, transformer position and switching need to be built into the carcass design. Confirm the electrical specification and compatibility with the chosen cabinet detail before ordering.
  • Appliance points. Sockets behind a floating cabinet are unreachable once it is hung. Position them within the access zone or in an adjacent, reachable location.
  • Water where a wet bar or sink is involved. Where the composition extends into a wall-mounted bar unit, waste falls and supply routes have to be planned with the carcass depth in mind.
  • Switch and control positions. Confirm where a user actually stands when operating lighting, a fridge or a lift-up door — and make sure that position is not behind a swing door or inside a drawer run.

Coordinate the Sideboard With the Rest of the Joinery Package

Ordering this item as an isolated line usually produces two problems: finishes that almost match, and site programmes that collide. A wall-mounted sideboard rarely stands alone — it normally sits in the same room as tall dining storage, display cabinets and open shelving.

Placing those items with one supplier keeps the finish batch, the material lot and the production schedule together. Coherence is easier to achieve when the pieces are specified as one set: tall dining cabinet, glass-front dining cabinets, wall-mounted display cabinets and wall-mounted shelves can all be detailed to the same finish schedule and released on one production run.

Our published dark wood minimalist project shows how a sideboard behaves when it is part of that single set. The wall-mounted unit there carries double-layer floating shelves for bottles and ornaments, sits under a stone counter holding a coffee machine, and is lit by recessed soft lighting — while the same dark wood grain runs through the adjoining kitchen, dining zone and tea room cabinetry.

Set the Delivery, Handling and Installation Sequence

A floating cabinet arrives as finished panels, so the delivery plan has to protect that. If your package also includes work for other parts of the property — floating modular systems for the living area — those components arrive on the same delivery and need the same handling plan.

  • Packaging and container loading for finished faces, with panels kept upright and edged — worth specifying in the order rather than leaving to the forwarder.
  • Delivery route on site. Confirm lift dimensions, corridor widths and door openings against the largest panel before dispatch, not at the loading dock.
  • Trade sequence. Wall linings, painting, flooring and the first fix of electrical work all sit around this installation. Book the sideboard into the programme after those trades have completed their wet work.
  • Snag list and sign-off. Agree who inspects the unit on site, what the acceptance criteria are, and how any transit damage is recorded before installation begins.

SANTERSON supplies this scope as a turnkey package — design coordination, custom/OEM production, freight and door-to-door delivery, then installation support and after-sales. The service pages state response and resolution aims for after-sales issues; confirm those figures in your own contract terms for the project you are running.

Questions Worth Asking Before You Sign

Can we change a dimension after drawings are approved?

Only before production release, and any change to width, depth or counter specification should be re-priced in writing. After panels are cut, a change normally means replacing the affected carcass rather than adjusting it.

What if the site wall is not square?

Scribe and packer allowances are designed in when the deviation is measured and reported. What cannot be resolved later is a fixing line that lands between support points, which is why the backing detail belongs on the approved drawing.

Should the counter be ordered with the cabinet?

Yes. The top rail and support arrangement are designed around the counter's thickness and edge, and matching a stone top to a pre-built cabinet usually means cutting one of the two.

How do we keep the finish consistent with adjacent cabinetry?

Order them from the same package and approve physical samples across all items at once. Matching by written description alone is not reliable for grain, sheen or tone.

The Point of the Confirmation Stage

Every item above costs nothing to resolve on paper and becomes a variation order the moment it reaches site. The confirmation stage is where a made-to-measure wall unit stops being an attractive elevation and becomes something that can actually be hung, loaded and lived with.

Send us your drawings.

If you have elevations for a residential or villa project, share them with our team along with the wall build-up and the finishes you are working to. We will return a specification and quotation built around your site-verified dimensions — as a one-stop furniture and building materials supplier, covering production through delivery and installation support for projects outside China.