A U shaped walk in wardrobe is one of the easiest layouts to draw and one of the easiest to mis-order. The plan looks tidy on paper — three runs of cabinetry wrapping a room — but the purchase order behind it carries linear metres of carcass, several door systems, internal fittings split across three zones, plus lighting, skirting returns and site openings that all have to arrive at the same time. This guide walks through how we quantity-take and coordinate these wardrobes on residential projects, from the first measured drawing to the handover list.

Why the U shape multiplies your line items

Two of the three legs of a U run meet at internal corners, and both corner conditions have to be resolved before quantities can be trusted. In our U Shaped Walk in Wardrobes range the carcass is made to measure, so each leg is ordered as its own module set rather than as a nominal length. That single decision changes how you count everything else:

  • Linear run per leg. Measure the back wall of each leg separately and record the finished face dimension of the return leg, so door clearances are not double-counted at the corners.
  • Corner treatment. Either one carcass turns the corner with a blanking panel, or two carcasses butt together with a shared upright. The first keeps the internal shelf line continuous; the second gives cleaner door openings but adds a scribe and a filler to the order.
  • Square metre of frontage. Doors are quoted by opening area, not by run length, so the height you choose for the top section changes the door count as much as the width does.
  • Fittings per zone. Long-hang, shelf and drawer zones are counted per leg, which is why a U layout usually carries more hardware SKUs than an equivalent L shaped walk in wardrobe.

Step 1 — Freeze the measured drawing before you count anything

Quantities drift when the drawing and the site disagree. Before any counting, lock down four numbers on a surveyed drawing: finished floor level, ceiling or soffit height at each leg, the position of every door opening into the room, and the location of switches, sockets and air grilles that will land on a panel line. Our interior design service covers this space planning stage together with 3D renderings and production coordination, which is where most quantity errors get caught before they reach the order.

Two site conditions matter more than people expect. First, floor level: a U layout has three runs meeting at two corners, so a floor that is out of level shows up as an uneven scribe line at both corners rather than one. Second, wall plumb: out-of-plumb walls change the depth of each leg along its length, and made-to-measure carcasses are built to the drawing, not to the site average.

Step 2 — Break the order into five quantity groups

We take the bill of quantities for a walk-in in five passes. Doing them separately keeps the totals checkable, and it exposes any item that only exists because of the U geometry.

GroupUnit of measureWhat to record
Carcass and panelsPer module, plus linear metres of runLeg length, carcass depth, height segment, corner detail, scribe and filler widths
Door systemPer opening, by areaDoor type, number of leaves, track or hinge set, glass or solid panel, mirror glazing
Internal fittingsPer lineal metre of zoneRail lengths, shelf counts, drawer stacks, trays, shoe and accessory units
Lighting and electricalPer circuit and per fittingFitting type, driver location, switch position, wiring route to the panel cavity
Site interfacePer itemSkirting and cornice returns, architraves, ventilation grilles, floor fixings

Recording the unit of measure next to every line is not paperwork for its own sake. When a leg shrinks by 300 mm during a design change, you can re-price the affected group in minutes instead of rebuilding the whole take-off.

Step 3 — Count internal fittings zone by zone, not room by room

The most common under-order is internal storage. A U plan invites three different uses: full-height hanging on one leg, shelves and drawers on the second, and folded storage or display on the third. Price each leg as its own zone:

  • Hanging leg. Count single rails and double-stacked rails by lineal metre, then add drop-down rails separately if the top section is above comfortable reach.
  • Drawer leg. Drawer stacks are ordered as complete units with runners, so record stack height and front width together. Deep stacks for folded clothing and shallow trays for accessories are different items even at the same width.
  • Display leg. Glass-fronted or open shelving needs shelf supports, load-rated shelves and often integrated lighting; see our open walk in wardrobes range when the display side stays open to the room.

Add a small allowance for shelf re-configuration only if the carcass system actually supports it. Adjustable shelving needs a pitch of holes repeated up both sides of every bay, and that detail has to be on the shop drawing before panels are cut.

Step 4 — Coordinate doors, finishes and glazing as one package

Door selection is where coordination failures become visible in the finished room. Leaves must clear each other at the corner, and the top of the tallest door must clear the floor finish and any rug. Choose the operating type per leg:

  • Hinged doors suit the two outer legs, where the swing has room. Our matte sliding door wardrobes and hinged ranges share carcass depths, so a mixed scheme stays consistent.
  • Sliding doors suit the central leg when the room is narrow, but each opening needs track length and an overlap zone — which removes usable depth at the corners.
  • Glass fronts need glazing type and handle detail fixed early, because the frame profile affects the internal dimension of the bay. Glass walk in wardrobes with framed glazing read as joinery rather than furniture, which is usually what a project specification is after.

Fix one finish schedule for all three legs at once: carcass interior colour, exterior panel finish, edge banding, handle or profile type, and glass tint. A single schedule lets us produce the carcass, doors and matching built-in furniture — vanity fronts, sideboards, skirting-matched panels — from the same board batches, so grain direction and sheen match across the room.

Step 5 — Sequence production, packing and delivery around the site programme

A walk-in wardrobe arrives as several trades' worth of components in one delivery. Coordinate it against the site sequence rather than the calendar month:

  • Panels and carcass first, so the room can be closed off and other trades can work around it.
  • Doors and glazing second, kept in protective wrapping until painting and floor finishing are done.
  • Fittings, lighting drivers and hardware third, in clearly labelled crates keyed to the leg they belong to.

We handle freight forwarding, customs documentation and door-to-door delivery for project consignments, and label every crate against the drawing reference rather than a generic room name. On a U layout this labelling is what makes installation fast: each installer knows which leg a panel belongs to, and the two corner modules go in first so everything else can be scribed to them.

Step 6 — Close out with a snag list you can actually check

Before sign-off, walk the three legs in order and confirm: door alignment and overlap at both corners; drawer runners free of paint and floor debris; every rail fixed at the drawn height; lighting circuits tested with drivers accessible; and scribe lines consistent along all three runs. Record any replacement panel or spare part against the same drawing reference used on the crates, which keeps future maintenance requests specific.

Ready to price a walk-in layout? Send us the measured drawing with leg lengths, heights and your door preference for each run. We will return a module-by-module quantity schedule for the U shaped walk in wardrobe, including corner details, so you can compare tenders on the same basis. Visit our contact page to start.

FAQs

What is the narrowest room that works for a U shaped walk-in?

Work from circulation, not averages. Subtract the depth of both facing legs from the room width and check the remaining walking space against how you use the room — dressing in front of a mirror needs more clearance than passing through to change an item. Where the middle is tight, we reduce carcass depth on one leg or switch that leg to open shelving.

Do I order a U wardrobe as one unit or three?

As three measured legs plus explicit corner modules. Because our sizing is made to measure, each leg is drawn and produced separately; the corner detail — turning carcass or butting carcasses with a filler — is decided on the shop drawing and priced as its own line.

When should lighting be specified?

With the carcass, not after it. Fittings need a cavity, and drivers need an accessible location that is not blocked by a shelf or a door frame. Specifying lighting at the same time as panel lines avoids cutting into a finished panel on site.

How are quantities re-checked if the design changes?

Only the affected group is retaken. A change of door type changes opening areas and hardware, not carcass lengths; a change of room length changes carcass and fitting metres but not glazing type. Keeping the five groups separate is what makes that re-check fast.