A high gloss PVC cabinet order looks simple on a quotation and complicated on site. The checklist below covers the eleven items that decide whether the doors you approved in the sample match the doors that arrive on site, open correctly and stay flat and shiny years after handover.
1. Scope: what is actually being priced
Before comparing finishes, confirm that the quotation describes the same job. A cabinet price that excludes plinths, scribes, filler panels, splashbacks behind appliances or the return panel at an open end will look cheap until those items appear as variations. Ask for a line-by-line scope list and mark what is included and excluded.
- Cabinet carcases, doors and drawer fronts listed separately, so you can see where the gloss finish applies
- Plinth, scribe, filler and end panels in the same finish or a stated alternative
- Internal fittings: shelf pins, adjustable shelves, baskets, hinges and slides by named brand and model
- Worktop interface detail: how the carcase is prepared for the stone or engineered stone top you are buying elsewhere
2. Door construction and substrate
"High gloss PVC" describes a surface film, not the board underneath it. Two cabinets with identical-looking doors can behave very differently near an oven or a sink. For our High Gloss PVC Cabinets, the product page states made-to-measure sizing, material and finish options and a layout tailored to the project — which means the substrate behind the film is something you specify, not something you accept. Ask in writing what board is used for doors, drawer fronts and carcases, how the edges are finished, and whether the same construction is used on tall doors as on standard ones.
Edge treatment matters more than most buyers expect. A gloss film wrapped over a well-bonded edge holds its line; a poorly bonded edge lifts first at the handle cut-out and at the bottom of tall doors. Request a cut sample so you can see the edge, not just the face.
3. Gloss level, colour match and grain direction
- Confirm the exact gloss reference by name and code, and keep the approved physical sample with the delivery note
- Check that doors from different production batches of one run carry the same shade — request a single batch for one kitchen
- If the design uses a wood-effect gloss, confirm grain direction across the elevation and how the pattern is cut at panel joints
- Compare the sample against the wall and floor finishes under the actual lighting scheme, not only in daylight
4. Handle detail and door edges
Gloss surfaces show every fingerprint and every chipped corner, so the opening method is a durability decision. Integrated profile handles, push-to-open or routed grooves avoid protruding hardware and reduce edge damage. Where pulls are used, confirm the fixing detail from the back of the door so no fixing head contacts the appliance cavity behind. If you prefer a handleless look across the whole kitchen, compare with Handleless Minimalist Kitchen Cabinets and keep the same opening method on wall units, base units and tall units.
5. Hardware specification in writing
| Item | What to specify | Why it fails later |
|---|---|---|
| Hinges | Brand, series, soft-close or not, opening angle, load rating for tall doors | Sagging and self-closing doors that knock |
| Drawer slides | Full extension, load rating, soft-close, runner colour | Drawers that bind under pantries' weight |
| Shelf support | Adjustable system and depth rating | Bowed shelves in wide wall units |
| Kickboard | Material, height, moisture protection at the floor line | Swelling where mopping meets the base |
6. Made-to-measure dimensions and site tolerance
Gloss panels expose out-of-plumb walls more than a matte, textured door does. Take dimensions after the plasterboard, tiling and screed are complete, or state clearly on the order which stage the measurements refer to. Record floor level variation across the run, the position of soil and waste pipes, and the depth available at corners, then have the supplier's drawing show how scribes absorb the variation. For villa and apartment fit-outs where several rooms are ordered together, Custom Built-in Kitchen Cabinets let you set one dimension standard across kitchen, laundry and pantry joinery instead of reconciling three separate tolerances.
7. Layout, appliance interface and clearances
- Oven, hob, dishwasher and fridge model numbers fixed before the order, with ventilation clearance drawn on the elevation
- Door swing checked against adjacent units, handles and traffic routes — a tall gloss door that clashes with an appliance door is expensive to re-make
- Corner access method chosen once the layout is final: carousel, pull-out or blind shelf
- Worktop depth and upstand reconciled with the sink and tap you intend to install
8. Moisture and heat exposure by zone
Decide which zones the cabinets sit in and specify accordingly: beside the sink and dishwasher, behind the hob and oven, and any outdoor-adjacent or laundry position. Where cabinetry sits near a pool deck, terrace door or a laundry with high humidity, discuss whether a design from the Outdoor Ready PVC Cabinets range is the right choice for those bays rather than treating the whole kitchen as one specification. Also confirm the maximum surface temperature the door face and edge are expected to tolerate near built-in ovens.
9. Sample approval, mock-up and sign-off
Approve a full door sample that includes the edge, the handle detail and, where relevant, the glass option — see Glass Front PVC Cabinet for display bays in the same family. Photograph the signed sample with the purchase order number on it. Then define who signs off what: drawing approval, sample approval, and delivery inspection. One named approver per stage prevents a change request arriving after production has started.
10. Packaging, transport and receiving
- Corner protectors and interleaving on gloss faces, with doors packed separately from carcases
- Pallet labelling that matches the room-by-room drawing numbers, so the right panels go to the right floor
- A receiving routine: check each carton against the packing list before the installer signs, and photograph damaged gloss faces at the moment of unloading
- Storage on site: flat, dry, off the floor, and out of direct sun until installation
11. Installation sequence, protection and after-sales terms
Gloss doors should be fitted last, after painting, flooring and stone fixing, and protected with film that the installer removes rather than leaves on. Confirm who is responsible for snagging hinge alignment and door gaps, which parts are covered as spares, and how a replacement door is matched to a batch that may no longer be running. Read the warranty terms for what is excluded — site moisture damage and impact chipping are usually outside coverage.
A short version of the checklist
- Scope line by line, including plinths, scribes and end panels
- Substrate and edge detail for doors and fronts, in writing
- Gloss reference, batch consistency and grain direction
- Opening method consistent across all units
- Hinges, slides and shelf supports named by brand and model
- Final site dimensions with tolerance recorded
- Appliance models and clearances fixed before ordering
- Zone-by-zone moisture and heat specification
- Signed sample and mock-up held against the order
- Packaging, labelling and receiving routine agreed
- Install sequence, protection and after-sales terms defined
If you want a second opinion on your drawing before ordering, send us the elevation and the appliance list. We check the specification against how the cabinets are actually built and quote made-to-measure high gloss PVC cabinetry for residential kitchens, apartments and hospitality fit-outs.
SANTERSON — China-based manufacturer of furniture and building materials, supplying custom kitchen cabinetry and interior fixtures for villa, hotel and office projects since 2008.
Phone / WhatsApp: +86-13928214007 (PHILLIP) | Email: santerson@qq.com