You have two or three quotations in hand, similar totals, and no clear way to choose between them. The difference usually lies in what each supplier has actually committed to supply — and that is precisely what samples and written proposals are meant to settle. Below is the comparison method we apply with project buyers on villa, hotel and office fit-outs, so you can place every offer on the same footing before a deposit is paid.
Start With the Scope Each Proposal Covers
Suppliers package the same job differently. One quotation may cover loose furniture only; another includes built-in cabinetry, wall panelling, flooring and lighting. Before comparing any prices, write down for each offer:
- Which rooms and which line items are included — and which are explicitly excluded.
- Whether built-in joinery such as wardrobes, vanities and kitchen cabinetry is priced in the same lot as loose pieces.
- Who handles freight, customs paperwork and delivery to site.
- Whether installation, inspection and replacement of damaged items form part of the price.
A lower total that leaves out freight and installation is not cheaper. As a one-stop furniture and building materials supplier, we quote the full package — loose and built-in furniture, sanitaryware, lighting, flooring, wall and ceiling finishes — on one scope sheet, so buyers can check line by line instead of guessing what sits outside the number.
Read the Specification, Not Just the Rendering
Two items that look identical in a picture can differ widely once they are specified. Ask each supplier to state, for every key item:
- Substrate and structure — solid wood, plywood, particleboard, aluminium frame, engineered stone, sintered stone.
- Finish system — high gloss or matte acrylic, lacquer, melamine, wood veneer, PVC wrap, rope weave, synthetic wicker, teak-look slats.
- Hardware and moving parts — hinge and runner brand, soft-close fittings, the mechanism on a motorised louvered pergola.
- For outdoor pieces, the frame material and how the weave, cushion foam and tabletop are fixed to it.
Where a design calls for made-to-measure work, ask what sits behind the word "custom": 3D modelling, prototyping before production, and which materials and finishes are genuinely available rather than merely shown in a photograph. Our Custom & OEM Service page sets out those steps, so you can ask any other manufacturer for the same level of detail.
Judge Samples on Four Points
Order physical samples of the finishes and one representative item per category before signing anything. Then assess them against fixed criteria rather than first impressions:
| Check point | What to look for |
|---|---|
| Colour and sheen under your own lighting | View the sample in daylight and in the actual room lighting; high gloss acrylic and matte lacquer behave differently under warm LEDs. |
| Edge and joint work | Examine edge banding, mitres, panel gaps and routed handleless profiles — these reveal factory discipline far faster than the front face. |
| Hardware feel and fixing method | Open and close doors and drawers repeatedly; check how woven outdoor elements are anchored to the frame. |
| Marking, packing and documentation | Sample cartons show how items will be labelled, protected and packed for a container, which matters long before site delivery. |
Keep every sample with its quotation reference. Once three or four offers arrive on your desk, unlabelled samples are impossible to match back to the paperwork.
Put the Commercial Terms Side by Side
The proposal text carries as much risk as the product list. For each offer, confirm in writing:
- Payment stages and what triggers each one — drawing approval, sample approval, release before shipment.
- Production sequence — when drawings are issued for your sign-off, and which changes remain free after that point.
- Freight mode, Incoterms, who prepares the customs documents, and whether cargo insurance is included or optional.
- What happens to items that arrive damaged, and how replacements are produced and shipped.
- Who installs on site, what inspection follows installation, and what after-sales support covers afterwards. Ours are described on the logistics and door-to-door delivery and installation and after-sales support pages.
If a claim in a proposal cannot be traced to a written clause, treat it as undecided. That applies equally to lead times, warranty periods and any statement about standards — ask the supplier to state what they will actually certify for your project.
Before You Sign: A Short Verification List
- Every proposal priced against the same room-by-room scope sheet.
- A sample approved and signed for each finish family you intend to use.
- Material, finish and hardware stated per item, with no "or equivalent" clauses.
- Freight, insurance, customs paperwork and delivery address recorded in writing.
- Installation, inspection and replacement terms named, with responsibilities assigned.
- Project references you can actually examine — for us, the published Australian villa projects on the project cases page are a reasonable starting point for that check.
If you are comparing suppliers for an Australian villa, hotel or office fit-out, send us your room schedule together with the quotations you hold. We will return a scope sheet, a specification list and sample suggestions, so the comparison is made on like-for-like terms rather than on headline price alone.
Common Questions
How many samples should I order before deciding?
One per finish family you plan to use — cabinetry door and carcass, stone or countertop, outdoor weave and frame, carpet or flooring, lighting fitting. That is normally enough to judge colour and build quality without commissioning a full mock-up.
What if two proposals give different product names for the same item?
Ask both suppliers to describe the item by material, finish, dimensions and hardware instead of trade name. A specification written that way compares directly; a model code from each factory does not.
Should the lowest quotation always be rejected?
Not necessarily. A low price is acceptable once the scope sheet matches and the specification is as detailed as the others. It becomes a risk only when exclusions, thinner materials or absent after-sales cover explain the gap.