A wall mounted bar unit looks simple on a drawing: a box fixed to a wall, some shelving, a worktop, maybe a light. In production it is one of the less forgiving items in a joinery package, because everything that can go wrong — load, fixing, services, finish mismatch — becomes visible only after the unit has left the factory. If you are specifying Santerson Wall Mounted Bar Units for a villa, apartment or hospitality project, the points below are worth closing out before production starts.

1. The wall itself, not just the cabinet

A suspended unit carries its own weight plus bottles, glassware and appliances, all of it shifted away from the wall face. Before we cut anything, confirm what the substrate is on site — masonry, stud partition, timber battening or a finished panel system — and where the blocking or solid backing will be installed. This matters most when the same wall also carries wall panelling or a decorative finish, because the fixing detail has to be resolved together with the panel build-up rather than after it.

Practical items to close out: the finished wall line and any reveal, the position of rails and services that must not be drilled into, and whether the fixing method we assume is compatible with what your site team will actually build. Send us the setting-out drawing with dimensions taken from the finished surface, not the structural face.

2. Made-to-measure dimensions and the layout inside

Our wall mounted bar units are made to measure: overall width, height and depth, and the internal arrangement are set per project. Two details cause the most rework when they are left open:

  • Internal zoning. Where glassware hangs, where bottles stand, whether you want drawers, a concealed compartment or an open niche. Tell us what the unit has to hold, and we will set the shelf heights around it rather than defaulting to equal bays.
  • Interface with adjacent work. Where the unit meets kitchen cabinetry, a sideboard, a doorway or a corner, decide which element takes the scribe and which is cut back. A 10 mm ambiguity at this stage becomes a visible gap on site.

If a wall mounted unit competes for the same wall, compare it against Santerson Integrated Bar Systems or Santerson Compact Bar Cabinets at the design stage. Choosing a floor-standing format later changes the flooring line, the skirting detail and sometimes the ceiling.

3. Materials, finishes and how they will be matched

Material and finish are specified per project — veneers, lacquers, laminates, glass fronts, metal frames and stone or marble worktops are all within our range. What needs confirming in writing is the reference, not just the name. "Oak veneer" from three different suppliers will not match. Agree a physical sample, a board number or an approved panel you already have on site, and note which surfaces are being matched: the bar unit to the kitchen, or the bar unit to the wall panelling.

Also confirm grain direction and whether edges and returns are visible. A unit seen from two sides needs a different edge treatment than one butted into a return, and that decision changes both cost and production time.

4. Lighting, glass and any services in the unit

Integrated lighting is one of the most requested options, and it needs the earliest decision because it drives cable routes, transformer position and an access point for maintenance. Confirm: switching location, whether the driver sits inside the carcass or remotely, colour temperature consistent with the lighting scheme for the rest of the room, and who provides the electrical first fix on site. Electrical specification and compatibility have to be confirmed against each cabinet design, so send us the luminaire you have in mind rather than leaving it as a note on the drawing.

For glass — shelving, fronts or display panels — confirm the glass type and thickness you expect, edge polish, whether fittings are bonded or mechanically fixed, and load assumptions. If the unit sits in a hospitality setting, ask us about hardware grade and expected duty cycle rather than assuming residential fittings will do.

5. Packaging, delivery and the site sequence

A wall mounted unit is one of the last things that should arrive, because it needs the wall finishes complete and the fixing positions set out. Confirm with us the container mix and packing method, the offload point, and whether the units ship with the rest of the joinery package or in a later consignment. Our scope runs from design and production through to door-to-door delivery, with installation support and after-sales service available — but the site programme is yours, so tell us the sequence you are working to and we will build the shipment around it.

6. What we need from you before we release the drawings

  • Room layout with finished dimensions, wall construction and fixing constraints
  • Intended contents and internal zoning for the unit
  • Approved finish references and the elements they must match
  • Lighting and services schedule, including switching and driver location
  • Delivery address, access conditions and target site sequence

Close those six points out first and production moves quickly. Send us the drawings early and we will return a marked-up proposal with the questions that still need answering — which is far cheaper than resolving them on site.