A clear glass aluminum frame wardrobe proposal usually arrives looking complete: a rendering, a set of elevations, a finish note and a unit rate. The differences between two such proposals are rarely visible on the first read. They sit in what the drawings do not state — how far the carcass has been dimensioned, which hardware carries the door weight, how glazing is handled in transit, and who signs off the opening before fabrication starts. For a commercial fit-out, where wardrobes appear in guest rooms, staff accommodation, spa change rooms and serviced-apartment units, those gaps turn into variation orders later. The checklist below follows the order in which decisions actually have to be made.
1. Read the scope before you read the price
Start by checking what the quotation is measuring against. A wardrobe priced from a designer's elevation and a wardrobe priced from a site survey are not the same offer. Clear glass with a slim aluminum frame reads as a light, transparent volume in a rendering; on site it needs to clear skirting, door reveals, ceiling lines, cornice, sprinkler heads and any pipework running behind the wall. Ask which dimensions were taken by the supplier and which were assumed.
Our Clear Glass Aluminum Frame Wardrobes are made to measure, with the layout, finish and dimensions specified per project rather than chosen from a fixed module list. That matters commercially because the unit price follows the actual opening and internal configuration, not a standard size you then have to scribe or pack out on site.
2. Confirm the glass specification in writing
"Clear glass" covers a wide range of product, and the price difference is significant. Pin down, item by item: glass thickness; toughened or laminated safety grade; edge treatment (polished, seamed or bevelled); whether the pane is clear float, low-iron for reduced green cast, or tinted; and where a decorative option such as ribbed or frosted is substituted on some doors only. Frame colour and surface treatment — anodised, powder-coated or wood-effect — should also be stated by reference, not by photograph.
Where a project needs the same frame profile with a different level of transparency, ask for the alternatives on the same drawing. Smoked Glass Aluminum Frame Wardrobes and Frosted Glass Aluminum Frame Wardrobes sit in the same glass-and-frame family, so comparing them side by side shows what transparency costs you and where a change is worth making — typically in guest rooms, where fully clear doors expose contents to the room.
3. Ask how the doors are engineered
Glass doors are heavy relative to their edge profile, and this is where a thin proposal becomes obvious. Ask which hinges, pivots or sliding gear are proposed, what load each is rated for, whether an adjustment is possible after installation, and how the top and bottom rails are fixed back to the carcass. For full-height wardrobe runs, confirm the maximum single-leaf size being offered and where intermediate posts have been introduced.
Internal specification belongs in the same conversation: drawer boxes, soft-close fittings, shelf spans, hanging-rail positions, integrated lighting and any mirrored or solid-panel doors mixed into the run. A single line item covering "internal fit-out" gives you nothing to compare between suppliers.
4. Check how the package arrives and gets installed
Glazed joinery is the item most likely to be damaged in international freight, so packaging detail is a commercial question rather than a technical one. Ask for the crating method, how panes are separated and supported inside the crate, whether spare glazing beads or trim are shipped loose, and how crates are marked against room or unit numbers so the site team can sequence installation instead of sorting a mixed stack.
For an overseas order, also confirm who prepares shipping documents, what delivery terms apply, and where responsibility for the goods transfers. Then check the handover: which party fixes the unit to the wall, who carries out the snag inspection, and what is covered afterwards for spare parts or replacement hardware. These points belong in the contract before production starts, not after the container has shipped.
5. Compare proposals on the same basis
Put every offer into one table: surveyed dimensions, glass specification and safety grade, frame finish reference, hardware make and load rating, internal configuration per unit, packaging standard, delivery terms, installation responsibility and after-sales coverage. A proposal that looks cheaper usually wins on one column and loses on three others — most often because the buyer ends up sourcing glazing, hardware or installation locally to close gaps the supplier never quoted.
Our one-stop solution covers that sequence from one point of contact: design consultation and space planning, material selection and product specification, manufacturing with quality control, project management and site coordination, then installation and handover. The Custom & OEM service handles bespoke finishes, textures and prototyping when a scheme calls for something outside the standard catalogue, and logistics and door-to-door delivery covers freight, customs paperwork, container loading and shipment tracking. Where a project also needs matching aluminum frame glass wardrobes, cabinetry or other built-in joinery from the same specification, coordinating them together removes the coordination risk between several suppliers.
Before you sign
Send us the room set, the target handover date and the finish direction, and we will return a proposal with dimensions, glass and frame specification, hardware schedule and packaging method stated separately — so it can be compared line by line against any other offer. Confirm final dimensions and selected specifications for each project before production.