An open bookshelf looks simple on a drawing: a set of shelves, some vertical sides, and a wall behind it. On site it behaves differently. The wall may be hollow, the floor may not be level, a shelf span may be longer than the board can carry, and the ceiling line may meet the unit at an angle nobody planned for. An installation plan is the document that turns those unknowns into decisions before production starts.

For Open Bookshelves and the wider built-in range, dimensions, layout, materials and finishes are specified per project. That flexibility is exactly why a written plan matters: nothing arrives pre-decided, so every choice has to be recorded somewhere before it reaches the factory floor or the site team.

1. A measured drawing of the wall, not just of the unit

Start with a survey of the space. The plan should record the finished floor level, the finished ceiling level, the position of skirting or architraves, and whether the wall behind the shelving is solid, framed, tiled or clad. A wall that looks straight over one metre can move by several millimetres across four, and an open unit running the full length will show every bit of it.

Write down what is inside the wall as well: power outlets, switches, data points, downlights, pipes, air-conditioning grilles and structural studs. Any of these can change where a vertical side or a fixing batten may sit. Where a full-height run is intended on Santerson Floor to Ceiling Bookshelves, the plan needs the exact finished height at several points along the wall, not one average number.

2. Span, load and shelf depth stated together

Three numbers decide whether a shelf performs: the clear span between supports, the depth of the shelf, and the load it will carry. A bookshelf is a heavy, point-loaded piece of furniture; paper is dense, and a full row of books concentrates weight along the front third of the board.

The plan should show, for each bay, the span and the intended use: paperbacks, hardcovers, display objects, or light decorative items. Where a bay is wider than the rest, say so and record what was done about it, whether that is a shorter span, a deeper board, a mid-span support, or a change of substrate. A plan that lists only overall width and height has not answered the question that matters most.

Ask the same question about depth. A shallow shelf reads neatly in a living room but will not take a standard hardback standing upright. Record the internal clear depth, because carcass thickness eats into it, and record whether the back panel is structural or decorative.

3. Fixing method matched to the actual wall build

Open units have no closed back to hide a bracket, so the fixing strategy is visible and has to be settled early. The plan should name the fixing type and the substrate it goes into: solid masonry, timber studs with noggins, steel framing with ply backing, tiled wall, or a clad panel. If the wall cannot take the load directly, the answer is usually a battened substrate or a floor-supported carcass, and that decision belongs in the plan rather than in a conversation on delivery day.

For tall runs, record where anti-tip restraint goes and whether the unit bears on the floor or hangs from the wall. record who supplies the fixings, be it the joinery supplier, the framer or the installer, because a missing bracket on site stops the job.

4. Interface details drawn, not assumed

Most snags on built-in shelving happen at the edges, where the unit meets something else. The plan should include detail lines for:

  • the junction with the floor, including skirting treatment and whether the unit is scribed or undercut
  • the junction with the ceiling, including shadow gap or cornice, and how a sloping ceiling is handled
  • the reveal to an adjacent door opening, window architrave or internal corner
  • the transition to another built-in element such as Santerson Full Height Storage Walls or a media wall, where depths and module heights have to align
  • the gap around radiators, vents and switch plates

Where the shelving sits inside a larger joinery run, fix the module heights first. A shelf that finishes at 1,100 mm in one room and 1,120 mm in the next will be noticed by the client even when nothing else is wrong.

5. Lighting, power and services coordination

Shelf lighting is a wiring decision made long before the boards arrive. If integrated lighting is part of the design, the plan must show which shelves take a channel, where the driver sits and stays accessible, how cable is routed through the carcass, and who terminates the supply. A driver buried behind a fixed panel is not serviceable.

Also record switch location, dimmer compatibility and the electrical specification agreed with the electrical contractor. If lighting is not part of the design now, leave the channel and the cable route in the plan anyway. Retrofitting into a finished unit is far more disruptive than preparing it during manufacture.

6. Finish schedule and sample approval

Open shelving shows its edges, so the finish schedule needs more than a colour name. State the substrate, the surface material, the edge treatment for every visible edge, and the sheen level. A veneer-matched edge and a painted edge read differently under the same light, and both may be listed as "oak".

Record which samples were approved, by whom, and on what date, and note where the same finish appears elsewhere in the project. Kitchen cabinetry, wardrobes, doors and wall panelling all need to match if they are visible together. Where a shelving run continues into another room as part of Santerson Modular Bookshelf Systems, the finish schedule should be one document covering both, not two.

7. Sequence, access and site conditions

A workable plan says what happens in what order. Confirm that first fix, wiring, plastering, painting and flooring are complete before the unit is measured for manufacture, or state clearly which dimensions are provisional and when they will be verified. Long shelves do not fit through a stairwell; note the delivery route, lift size, and whether modules need to be split for access.

Include the practical items too: where the units are stored on site, how finished floors are protected, the conditions boards are kept in before installation, and the date the unit must go in relative to other trades. These are the details that separate a smooth install from an overnight fix.

8. Handover checklist

Close the plan with what "done" means: shelves level and aligned, any doors or drawers adjusted, fixings concealed, surfaces free of damage, lighting tested, and snags written up with owners and dates. Attach the approved shop drawing and the finish schedule so the site team and the client sign off against the same document.

How a supplier-side plan differs from a site-side plan

A site installation plan tells the installer what to do. A supplier-side plan also fixes what will be manufactured, and it has to be reviewed before production begins. As a custom furniture and interior products manufacturer, we work from drawings that state dimensions, material, finish, edge detail, hardware and packing split together; anything left unstated becomes an assumption on site.

For villa and apartment projects the shelving is usually one item inside a larger package of built-ins and loose furniture. Coordinating it as part of that package avoids the common problem of a bookshelf ordered late, made to a different finish code, and fixed to a wall that has already been dressed.

If you are preparing an installation plan for a project, send us the measured drawings, the wall build-up and the intended loading. We will review spans, supports, fixings and finishes with you before production and flag anything that would cause a problem on site.