Smoked veneer wardrobes sit at an awkward point in most project schedules. They are built-in furniture, so they have to be measured accurately, yet the room around them is rarely finished when the enquiry first goes out. Send a supplier a vague request and you get a vague price; send drawings with the wrong opening dimensions and you re-order joinery weeks later. The preparation below is what we ask buyers, contractors and designers to have ready before the first conversation about smoked veneer wardrobes, and it applies equally to a single villa bedroom or a run of guest rooms.
1. The room information, not just the wardrobe size
A made-to-measure wardrobe is only as good as the dimensions behind it. Before you write to a supplier, collect the length, height and depth of each wall the unit will occupy, and note where the floor meets the wall — out-of-level floors are common on site and change how a tall carcass is scribed and packed. If the design calls for a full-height unit, confirm the structural ceiling height rather than the drawn one.
Then mark the fixed elements: skirting lines, door swings, light switches, air-conditioning outlets, power points, and any window reveal the wardrobe has to stop against. A single line drawing with these items labelled saves several rounds of email. If your project already has interior drawings, send them even if they are not joinery-level; a supplier working from floor plans can tell you quickly which walls are workable.
2. How the wardrobe will be used
Internal layout is driven by habit, not by aesthetics, so describe the use before asking for a price. Long hanging for coats and dresses needs a different clearance than a shelf-heavy guest-room unit. Tell the supplier how many hanging rails you expect, whether you want drawer zones, whether an ironing or luggage position is needed, and whether anything has to sit above the doors.
For multi-unit projects, say who occupies the rooms. A family villa, a serviced-apartment block and a hotel floor each have different storage expectations, and that difference changes the internal kit far more than the door finish does. If you are open to custom minimalist bedroom wardrobes with handleless fronts, mention it here — a seamless panel surface affects the clearance needed for opening and the hardware specified.
3. The finish you actually want, in writing
“Smoked” describes a tone range, not one fixed colour. Veneer sheets differ in grain figure, in how much grey or brown sits in the stain, and in whether the surface is left matte or built up to a higher sheen. Rather than naming a shade, send a reference image of a room you like, plus any physical sample or project photograph you already hold, and state clearly what must match: an existing door set, a flooring tone, or a piece of loose furniture.
It is worth asking which finishes sit in the same collection, because consistency across a building usually matters more than one perfect panel. Within the wood veneer wardrobe range you can compare walnut veneer wardrobes and natural oak veneer wardrobes against the smoked option before locking a specification. Confirm the finish, substrate and edge treatment for each project in writing — product pages describe configurable options, not a fixed bill of materials.
4. Your programme and delivery address
Built-in joinery has to arrive after the wet trades have finished and before flooring, lighting and loose furniture are installed. Give the supplier your target installation month, plus the date you expect walls and floors to be ready for final site measurement. That single date determines whether the unit is made to drawing or made to a measured survey.
For overseas sourcing, share the delivery address and who receives goods on site. A supplier handling furniture logistics and door-to-door delivery can arrange sea, air or rail freight together with customs paperwork, packing and container loading, but they need the destination, the access conditions and the receiving arrangement early — packaging for a high-rise lift is not the same as packaging for a house with a driveway. Ask what is included in the quoted price and what stops at the kerb.
5. The scope around the wardrobe
Wardrobes rarely stand alone. Mezzanine panels, matching vanity units, bedside joinery and door linings all draw from the same material and finish decision, and ordering them together keeps tones consistent across the room. If your project also needs kitchen cabinetry or other built-in furniture, say so at the start; a supplier who manufactures across the whole interior can align the finishes that a patchwork of vendors would get subtly wrong.
The same logic applies to an entire building. Where several rooms, several villas or a hotel floor are being fitted out, an interior fit-out supplier can coordinate joinery alongside the other fixtures and finishes under one production and delivery plan, which removes the coordination burden from your site team.
6. What to ask the supplier back
A quotation is only comparable if the assumptions are visible. Ask for the material specification in writing, the hardware brand or series, how the unit is delivered (assembled or flat-packed), who performs the final site measurement, and what happens if on-site dimensions differ from the drawings. Also ask which stage of the process requires your sign-off — production should never start before you have approved shop drawings.
SANTERSON has been manufacturing furniture and building materials since 2008, and works with villa, hospitality and office projects from design through to installation: space planning and 3D rendering, custom and OEM manufacturing, door-to-door delivery, and installation support. If you would like a quotation for bedroom joinery, send your drawings and finish references and we will confirm the specification before production.
Send us your room dimensions, layout notes and finish references, and we will confirm the specification and price for your project. As a one-stop furniture and building materials supplier, we can also match the wardrobe finish to the cabinetry, wall panelling and flooring specified elsewhere in the same project.