Ask three suppliers for a price on European oak engineered parquet and you will probably receive three different numbers. The gap is rarely about timber margins. It is about what each supplier assumed, because the request they received left those details out. A quote that looks cheap has usually priced a smaller order, a shorter board, a lighter wear layer or a finish you did not ask for.

The practical fix is to send the same complete brief to every supplier and compare like with like. Below is the information a manufacturer needs before it can put a reliable figure against engineered wood flooring, and why each detail changes the price.

1. The layout pattern, not just "parquet"

Parquet is a family of patterns, and each one carries different material waste, different board dimensions and very different installation labour. Herringbone blocks laid at 90 degrees are not interchangeable with chevron, where the ends are pre-cut to meet at a point, and neither behaves like a classic square panel layout with a border. State the pattern you want and, where possible, attach a reference image or a sample number from the supplier's range.

This matters for budget as much as appearance. Patterned floors generate off-cuts at every wall, and the tighter the geometry, the more the wastage allowance climbs. Give the supplier the room dimensions and note irregularities — bay windows, columns, stair nosings, door thresholds — so the order quantity reflects your plan rather than a rounded guess.

2. Board size and the top-layer construction

Width and length drive price more than most buyers expect. A long plank uses more oak per board and costs more to produce, pack and freight than a short one of the same species and finish. Then there is the top layer: our European oak floors are built with a 3 mm solid oak wear layer over a multilayer base, which is thick enough to sand and refinish while keeping the dimensional stability that a solid board cannot offer on a heated slab.

Tell the supplier the total thickness you need, the top-layer thickness and the board format. If your detail drawings already specify a build-up — acoustic underlay above a concrete slab, for instance — share them, because the substrate decides which construction is appropriate.

3. Grade, colour and finish

Two boards cut from the same log can look completely different. Grade describes how much sapwood, mineral streak, knot and colour variation you are prepared to accept, and it changes yield at the sawmill, so it changes price. Be explicit: a clean, even floor and a characterful floor with visible knots and grain movement are not the same specification.

Then specify the finish system in the same sentence as the colour. Brushed and wire-branded surfaces open up the grain and hold more pigment; smoked and fumed finishes react with the timber rather than sitting on it; UV-cured lacquer and hardwax oil protect differently and show wear differently. The ranges we produce include light tones with natural knots, warm honey and smoked shades, deep brown boards, and charcoal planks with bold grain — each needs a different finishing pass.

4. Quantity, rooms and the schedule that actually matters

What to stateWhy it moves the quote
Square metres per room, plus sparesMixed small lots cost more per square metre than one consolidated order, and reordering later rarely matches the batch.
Number of units or storeysDetermines how many pallets, how many container loads and how the shipment is split.
Required on-site date, working back from handoverProduction slots are booked in sequence; a compressed programme may need staged shipments.
Delivery address and IncotermsFreight, customs handling and last-mile delivery are quoted to the site, not to the port, unless you say otherwise.
Storage available at siteTimber needs a dry, acclimatised place to sit. No storage means staged deliveries, which is a cost line.

5. Substrate, heating and moisture

This is where quotes most often go wrong after the order is placed. Say what the floor is going onto: sand-and-cement screed, floating screed, timber deck, existing floorboard, or an acoustic system. Say whether underfloor heating is present, and if it is wet or electric. Several of our parquet and herringbone constructions are compatible with underfloor heating, but the compatibility depends on the build-up and on the screed being dry to the specified moisture content before a single board is laid.

If you have a moisture test result, send it. If you do not, say so, and the supplier can advise on what testing should happen on site before installation begins. A flooring order that arrives before the screed has dried becomes a storage problem and then a claim.

6. Matching an existing floor or a wider fit-out package

Renovation work rarely stops at one room. If new flooring has to meet an existing floor, send a sample board or at least the make, model and finish of what is already down, and flag the transition details you need — reducer strips, threshold profiles, skirting and scotia in the same finish. These small components are frequently left out of an initial enquiry and then added as extras.

Where flooring is one line in a larger package, say so. Coordinating floors with kitchen cabinets, wall panelling and doors from one source removes the arguments about which trade is responsible for where one product stops and another starts.

What a complete specification looks like in practice

Compare two enquiries. The first reads: "Please quote European oak parquet, herringbone, for a villa." The second reads: "Herringbone European oak engineered boards, 3 mm solid oak top layer, light bleached tone with a brushed lacquer finish, grade allowing limited mineral streak; laid straight except for a chevron detail at the entrance hall; one area per floor across four levels, measured drawing attached, plus a wastage allowance to be agreed; wet underfloor heating over sand-and-cement screed, moisture test not yet carried out; skirting and reducers to match; staged delivery to a Sydney site within the programme shown, storage for one pallet only." The second enquiry can be quoted accurately in one pass. The first invites three different answers, each priced against a different set of assumptions.

Sample references from our flooring range

European Oak Engineered Parquet Flooring

3 mm solid oak top layer with natural grain over a multilayer base; light oak tone suited to minimalist residential interiors.

European Oak Herringbone Engineered Wood Flooring

Light bleached tone with subtle grain; the multilayer structure is described as reducing warping in living rooms and bedrooms.

European Oak Parquet Engineered Wood Flooring

Rich deep brown grain in a classic parquet pattern, aimed at premium residential interiors.

Dark European Oak Herringbone Engineered Flooring

Deep natural grain on a high-stability base; the product page lists compatibility with underfloor heating for high-end projects.

Charcoal European Oak Engineered Wood Flooring

Bold grain with subtle knots under a deep charcoal finish for modern interiors.

Product descriptions on our pages state the top-layer thickness and general application, but board dimensions, grade definitions and heating limits are confirmed against current production specifications before an order is placed. Ask for those figures in writing rather than assuming a catalogue image represents your delivery.

How consolidated supply changes the arithmetic

Buying flooring separately from cabinets, doors, panelling and sanitaryware means separate freight bookings, separate packing standards and separate dates to police. As a one-stop furniture and building materials supplier, we consolidate those lines into one production programme and one shipment plan under our logistics and door-to-door delivery service, which covers freight forwarding by sea, air and rail, customs paperwork and container loading.

That consolidation only works if the brief is complete at the start — which brings us back to the same point. Send the pattern, the build-up, the grade, the finish, the quantity per room, the substrate condition and the programme, and a serious supplier will return a quote you can actually compare.

Before you send your enquiry

  • Pattern and layout direction, with a reference image or sample number
  • Board width, length, total thickness and top-layer thickness
  • Grade tolerance and finish system, named not implied
  • Square metres per area, wastage allowance and spares
  • Substrate type, screed age, moisture test result and heating type
  • Transitions, skirting and profiles required in matching finish
  • Delivery address, Incoterms, staging plan and site storage
  • Programme dates working back from handover

Send those details to our team with your drawings and we will quote against the specification you actually need rather than the assumptions we would otherwise have to make.