Matte acrylic cabinet doors arrive on site flat, finished and ready to install. That is exactly why the transit between our factory and your site matters so much: a soft-touch acrylic surface shows scratches, pressure marks and edge chips far more visibly than a textured one. Before production starts, buyers should settle the packaging question in writing, not leave it to whoever packs the goods at the end of the order.

As a China-based manufacturer supplying matte acrylic cabinets for villa, apartment and hospitality projects, we pack made-to-measure joinery for export every week. The checklist below reflects what we ask buyers to confirm at the specification stage, so the same details appear on your purchase order, your packing list and your inspection sheet.

Why matte acrylic behaves differently in transit

An acrylic-faced door is a substrate with a thin decorative skin bonded to it. Two failure modes dominate sea and road freight:

  • Surface marking. Abrasion from direct contact with another panel, cardboard fibre transfer, or protective film left on for months in a hot container can all leave marks that cannot be polished out of a matte finish.
  • Edge and corner damage. Chipped edges are the most common complaint on flat-packed cabinetry. Once the corner of an acrylic panel is chipped, the panel usually has to be remade rather than repaired.

Because our matte acrylic cabinets are made to your dimensions and finish selection, a damaged panel is not something you can replace from stock. Confirming the packing method before production is cheaper than arranging a replacement panel mid-project.

Seven points to confirm with your supplier

Point to confirmWhat to ask, and why it matters
Protective film on the facesAsk whether the acrylic faces ship with protective film applied, and how long the film is rated to stay on. Film left under heat and sunlight for a long voyage can become difficult to remove or leave adhesive residue. Agree when the film should be peeled: at unpacking, before installation, or only after on-site trades have finished.
Panel separationAsk what goes between door panels in a bundle. Panels stacked face-to-face with nothing between them will abrade. Confirm interleaving material and that it is clean, dry and non-shedding.
Vertical or flat orientationTall door panels travel best upright with support under the base and restraint at the top. Flat stacking across a long container voyage puts the weight of the stack on the lower panels. Ask which orientation is used for your panel sizes and how bundles are restrained inside the crate.
Edge and corner protectionConfirm protectors on corners and edge bands on visible faces, especially for dark colours where a light chip stands out against the body colour.
Crate specificationAsk what the crate is made of, whether it is fumigated or heat-treated timber where your import rules require it, and whether the crates are designed for the container height you are shipping to. For split shipments across several containers, ask how crate numbering maps back to your room-by-room drawing.
Moisture protectionA sea voyage means condensation inside the container. Confirm wrapping or desiccant use, and that panels reach the site dry. Panels that arrive damp need drying time before installation, which pushes out your site programme.
Hardware and glass packingHinges, runners, handles and any glass components should be packed separately from panels and marked with the same crate and unit references as the drawings. Loose hardware rattling against an acrylic face is a common source of marks.

Marking that matches your drawings

Made-to-measure joinery only installs quickly if every piece can be identified without opening crates. Ask for each panel to carry the same unit and item references used on the approved shop drawings, plus a crate list showing what is inside. On site, this is what lets an installer work room by room instead of unloading everything into a hallway.

The same applies to matte acrylic wardrobes, where tall full-height panels and mirror or glass inserts need different handling from shorter kitchen doors. If your project mixes cabinetry and built-in storage, ask whether the two are packed to the same standard and labelled in one consistent numbering system.

What we handle on a turnkey order

For projects where we manage both production and freight, packaging and container loading sit inside our furniture logistics and door-to-door delivery service, together with the shipping documents your customs clearance needs. That keeps one party responsible from the drawing stage to delivery at your door, rather than a handover between manufacturer and an unrelated forwarder.

If you are ordering cabinetry to a design you have already prepared, our custom and OEM service covers material and finish selection, prototyping and production to your specification. Either way, send the panel schedule early enough that the packing method can be written into the order rather than negotiated after the goods are finished.

Before you confirm: ask your supplier for a packing photo or a written packing standard for matte acrylic panels, and put it in the order file. At delivery, photograph any crate that arrives crushed or wet before signing, and check the faces of a few panels from different crates rather than only the top one.

Frequently asked questions

Should the protective film stay on during installation?
Follow the film supplier's guidance and your supplier's instruction. In practice, keep the film on while other trades work around the cabinetry, and remove it as soon as those trades have finished, so the film does not sit on the panel longer than it is rated for.

Can a scratched matte acrylic door be refinished on site?
Matte acrylic faces are not like solid timber that can be sanded back. Light surface marking may be addressed with the cleaner your supplier recommends, but deep scratches or chipped edges normally mean the panel is remade. This is why edge protection and separation in transit are worth specifying.

Do we need to inspect goods at the port or at the site?
Inspect where it is practical for you, but do it before installation begins and while a claim can still be raised. Check a sample of crates across the shipment, and record crate numbers on any damaged panel so a replacement can be identified against the drawings.

Send us your panel schedule

Share your dimensions, colour and finish selection, and we will confirm the specification and packing method for matte acrylic cabinetry on your project before production starts.

Furniture installation and after-sales support  |  WhatsApp / Phone: +86-13928214007  |  santerson@qq.com