Corner niches are the hardest part of an Australian bedroom or dressing room to fit out properly, and hinged door corner wardrobes are one of the most requested solutions for them. For villa renovations and apartment projects in Sydney, Melbourne, Perth and Willoughby, these units are usually made-to-measure joinery supplied from overseas, so the risk sits less in the design than in what gets confirmed before production starts. This guide sets out the checks that matter when you order hinged door corner wardrobes from an offshore manufacturer.

1. Verify the measured opening, not the drawn plan

Corner joinery rarely sits in a square, plumb box. Older Australian villas and units commonly have out-of-square walls, skirting that stays in place, and floor levels that vary across the corner. Before an order is released, ask for the measurement basis in writing: which dimensions are finished-floor to underside of ceiling, whether skirting is removed or scribed around, and where the tolerance allowance sits.

A practical check is to require a marked-up dimension drawing showing both legs of the corner, the overall depth of each run, and the clear opening width for every door. If the supplier works from architectural drawings only, confirm that a site-verified set of dimensions is taken after flooring and cornices are installed.

2. Confirm how the corner carcass is built

The internal corner post or diagonal return determines whether the space is usable. Ask which carcass construction applies to your unit: a shared corner post with doors hinged off each run, a blind corner with a carousel or pull-out basket, or a diagonal end return. Each option changes shelf depth, door size and hardware.

For the internal fitout, request the layout drawing that shows hanging rails, drawer banks, shelves and any L shaped corner wardrobe return run, with every dimension stated. Confirm load ratings for shelves and drawers in the specification sheet rather than accepting a general statement about quality.

3. Check door geometry and clearance before you commit

Hinged doors need swing clearance that corner positions often do not have. Verify the required clearance for each leaf against the adjacent wall, bed, or doorway, and confirm hinge type, count and whether soft close is included. Where clearance is tight, compare your option with sliding door corner wardrobes before finalising the layout.

Also confirm handle projection and whether the door reveals are rebated or overlapped, because these details affect how two leaves meet at the corner and whether the doors bind.

4. Specify materials and finishes in writing

Material descriptions such as "wood finish" are not enough for a made-to-measure order. Ask for the board type, thickness and edge treatment for carcass, doors and shelves; the surface material (veneer, laminate, lacquer or acrylic); and the colour or grain reference code. Where the wardrobe faces an ensuite or external wall, ask what substrate and edge sealing are proposed.

A reputable supplier will confirm your selected specification per project rather than offering one fixed recipe. If you are matching the wardrobes to other joinery in the same build, request physical finish samples before production so grain direction and sheen can be compared under site lighting.

5. Clarify supply scope, packing and delivery terms

Ask exactly what arrives: assembled cabinets or flat packs, doors hung or loose, hardware boxed separately, and how many packages to expect. For offshore supply this affects on-site handling, storage and install time. Confirm the Incoterms quoted, whether door-to-door delivery to your site is included, and who handles customs clearance and duties.

Request the packing list format in advance so the site team can reconcile cartons against the drawing schedule when the consignment lands.

6. Agree installation and after-sales terms

Establish who installs: your local joiner, or the supplier's installers if available in Australia. Confirm what fixing details are provided for the wall type on site, whether packing shims and scribes are supplied, and how the snag list is handled after fitting.

Get the warranty terms, replacement-part process and response expectations in writing before payment, and check which items are excluded. Terms quoted in marketing material should be confirmed for your specific project.

7. Check the supplier's Australian project evidence

Ask for references from completed Australian work, including the project location, scope and whether wardrobes or other built-in joinery were part of it. SANTERSON publishes Australian project cases in Willoughby, Perth, North Turramurra, Melbourne and Sydney, which is one reason buyers evaluating furniture sourcing for Australian projects consider them alongside the wider range of built-in and loose furniture.

Useful evidence includes production photographs of a corner unit before packing, installation photographs, and contactable references. Project listings alone do not establish scope or performance, so ask for detail on the specific job.

A pre-production checklist

  • Site-verified dimensions taken after flooring and cornices, with tolerances stated
  • Corner carcass construction confirmed, with internal layout drawing fully dimensioned
  • Door swing clearance, hinge specification and soft-close inclusion checked against the room
  • Board type, thickness, edge treatment and finish reference codes approved from physical samples
  • Hardware make, load ratings and quantity schedule confirmed
  • Incoterms, delivery address, packing list format and carton count agreed
  • Installer identified, fixing details issued for the actual wall type
  • Warranty terms, exclusions and replacement-part process received in writing

Most disputes over corner wardrobes trace back to a small number of unconfirmed items: measurement basis, corner carcass detail and door clearance. Settle those three in writing before production is released, then hold the supplier to the approved drawing at packing.

To specify hinged door corner wardrobes for an Australian villa or apartment project, send your room dimensions and finish references through the SANTERSON contact page, and request a dimensioned layout drawing with the material specification before confirming production.