Stone and marble wall panels carry their cost in two places: the material itself, and whatever happens after the container lands. A panel that arrives intact can still fail a project if the replacement piece takes weeks, or if nobody documented which finish was approved. Before you confirm an order of stone & marble panels, the questions below are the ones that decide whether the wall is still your problem or the supplier's.

Why after-sales matters more for stone than for most finishes

Cut stone and marble are dimensional products. A panel is measured for a specific wall, cut to a specific thickness, and finished on one face. If a single piece cracks in transit or is damaged during installation, a replacement is not picked up from a shelf — it is re-cut, re-finished and shipped again. That is why the after-sales conversation should happen while the purchase order is still being drafted, not after a problem appears on site.

The same logic applies to stone & marble surfaces used as vanity tops and counter runs. These are fabricated to the millimetre against a set of drawings, so an error in the drawing becomes an error in the stone, and the remedy is a remake rather than an adjustment.

1. What exactly is covered after delivery?

Ask for the coverage in writing, itemised by failure type, and check which of these it names:

  • Transit damage — breakage or chipping found when the crates are opened at site.
  • Fabrication defects — thickness variation, lippage risk, finish inconsistency between panels from the same batch.
  • Dimensional error — a panel that does not fit the opening it was measured for.
  • Finish problems appearing later — staining, etching or sealant failure under normal use.

Then ask what voids it. Panels installed with an adhesive the supplier did not specify, or cut on site to fit a reveal that was never on the drawing, are usually treated as site-caused. Getting that boundary in writing before you order is worth more than any verbal assurance afterwards.

2. How fast can a replacement panel actually reach site?

Response time and resolution time are different numbers, and buyers routinely confuse them. A supplier may acknowledge a claim within a day and still need weeks to re-cut, re-finish and ship the piece. Ask for both: how quickly someone replies with a decision, and how many days from that decision to the moment a replacement is on the truck. Some suppliers publish response targets on their service pages; treat those as starting points and ask what applies to your specific configuration.

Then ask about the shipping route for a single small parcel. A full container has a well-worn path; one replacement panel travelling by air freight is a different cost and paperwork exercise, and knowing that figure in advance changes how you plan the programme.

3. Are spares supplied with the order, or only on request?

The practical question is not whether spares exist but whether they will still match in three years. Stone and marble come from batches: veining, background tone and surface texture vary between blocks. A panel ordered as a spare two years later may be the same species and still read visibly different on the wall.

Two habits protect you. Order cut pieces for the most exposed areas — corners of feature walls, panels beside door openings — at the time of the main order, and crate them separately with a label naming the wall they belong to. Second, ask the supplier to record the batch, finish specification and cut list for your project, so a later enquiry can reference something concrete rather than a photograph.

4. Who installs it, and who answers when the installation goes wrong?

For projects abroad this is where responsibility most often falls between two parties. Ask whether on-site installation guidance or supervision is included, whether the fitters are supplied by the supplier or hired locally, and how snags are handled during handover. A supplier offering installation and after-sales support should be able to say plainly which stage of a problem sits with their team and which sits with the local contractor.

Practical test: ask what happens if your tiler cuts a panel wrongly. The clarity of that one answer tells you more about the after-sales arrangement than any brochure paragraph.

5. What documentation comes with the panels?

DocumentWhy you want it before installation
Approved finish and material specificationThe reference point for any claim about colour, texture or sheen.
Dimensioned cut list with panel numberingLets a replacement be ordered by number instead of re-measured on site.
Batch and block referenceImproves the chance that future spares match the installed wall.
Recommended adhesive, sealant and fixing methodProtects the warranty — deviations are usually excluded.
Cleaning and sealing guidanceBecomes part of the handover pack for the building owner.

Ask for these as deliverables in the order confirmation. A supplier used to export work will have a standard set; one that hesitates is telling you something about how claims will be handled later.

6. What does care and maintenance support look like after handover?

Stone walls fail slowly rather than suddenly. Sealed surfaces lose their protection, acidic cleaners dull a polished face, and movement joints open hairline cracks. Ask what happens when the building owner calls two years in: is there a technical contact who answers with advice on re-sealing or repair, and are repair materials available? For hospitality and villa projects that change hands between management companies, having that support line documented matters more than the original price per square metre.

A short list to settle before you order

  • Written coverage, split by transit, fabrication, dimensional and finish issues.
  • Decision time and replacement delivery time, quoted for your configuration.
  • Spare cut pieces ordered with the main batch, labelled by wall.
  • Named installation responsibility and a snag process at handover.
  • Specification, cut list, batch reference and care instructions in one pack.

As part of a turnkey project package, these answers arrive together with the rest of the fit-out scope, which is easier to manage than chasing several trades for one wall. Either way, put the questions in writing before the panels are cut — that is when they still cost nothing to ask.

To confirm dimensions, finishes and after-sales terms for a specific wall or counter run, contact SANTERSON at https://www.santerson.com/contact/.