A wall-mounted bar unit looks simple on a drawing: a run of cabinets, some glass, a worktop, a bottle store. The quotation for the same wall can vary widely between projects, because almost everything that drives cost sits behind the doors — how the carcass is sized, what the wall can carry, which appliances are being built in, and how far the finished joinery has to match the cabinetry already specified for the kitchen. If you are preparing an enquiry for Santerson Wall Mounted Bar Units, sending the right information with your first message is what turns a rough estimate into a price you can actually build to.
Start with the wall, not the cabinet
Wall-mounted bar units are made to measure for each project, so the starting point is the wall itself rather than a catalogue width. Before any sizing can be confirmed, a supplier needs a measured drawing or site survey of the recess or wall run: overall length, floor-to-ceiling height, and the position of any skirting, cornice, downlight or switch that the unit has to work around. Because these units are fixed to the structure, the wall build-up matters just as much as the dimensions — state whether it is masonry, studwork with a cavity, or an existing finished surface such as wood veneer panels, and note where structural fixings can be placed. Where a wall cannot carry the load on its own, that has to be resolved at design stage rather than discovered by the installer on site.
It is just as useful to say which side of the wall is which. A bar unit that reads as a feature in a villa living room may need a completely different back finish where it faces a corridor or a service zone, and matching an existing finish is far easier to price when the reference can be seen.
Decide the layout and what has to be stored
The next thing a supplier needs is a short list of what the unit must actually hold, because the internal fit-out — not the door style — sets most of the price. Glassware, decanters, bottled stock, bar tools, linen and consumables all want different shelf heights, drawer types and load ratings. A glass-front bar cabinet with lit display shelving is a different build from a closed unit that hides a full bottle store, and both are different again from an integrated bar system that wraps around appliances and tall storage.
It also helps to say whether the wall unit is the only bar element in the room. In open-plan villas and apartment projects a wall-mounted run is often designed alongside other pieces from the same collection, such as island bar units or compact bar cabinets, and where the whole set is quoted together the finishes, door profiles and hardware are specified once instead of reconciled later.
Specify finishes, but confirm what is available
Send the finish direction you are working to: paint colour or RAL reference, veneer species, lacquer sheen, metal accents, and the handles or handleless profile you want. Bar cabinets in this collection are offered with material and finish options selected per project, so a mood board, a finish sample reference, or simply the kitchen cabinetry the bar has to match is usually enough to start. Where you are matching an existing specification — for example a tall dining cabinet already installed in the same room — include the supplier reference or a photograph, and the manufacturer will confirm which surfaces can be reproduced before quoting, rather than promising an exact match on paper.
Appliances, glass and electrics need their own schedule
Anything with a cable or a compressor has to be declared up front. Wine storage, undercounter refrigeration, ice makers, extraction, kettles and glass-door coolers each set a minimum carcass depth, a ventilation gap, a door swing and an isolator position. Send the appliance model numbers, or at least the intended type and capacity, together with the local power supply details for the project — voltage, frequency and plug standard. This is also where integrated lighting belongs: integrated cabinet lighting has to be specified alongside the carcass so that profiles, cable routes, drivers and switching are built into the panels rather than surface-fitted afterwards. Electrical ratings and compatibility should be confirmed for the final cabinet design.
Worktops come next. State the material you want — stone, engineered stone, sintered surface or timber — along with the edge profile and whether the top is structural for the unit or sits on a separate support. Splashback returns and any joint to an adjacent wall finish should be shown on the drawing too.
Project context changes the quotation
Bar cabinetry is quoted as part of a project, not as a standalone item, so the surrounding information is genuinely useful. State the project type and location — villa, apartment, boutique hotel or office — the number of identical units required, and the room-by-room schedule the bar belongs to. A one-stop furniture and building materials supplier can hold the bar cabinetry together with the joinery, wall panelling, flooring and lighting around it under one production and shipping plan, which is what keeps finishes consistent across a development.
Delivery detail matters at this stage as well: the port or site address, the Incoterms you want quoted, and your target on-site date. For multi-unit work, send the unit schedule so that quantities per apartment or floor are clear; for a single home, one good set of measured drawings and photographs of the wall is usually enough.
What comes back from the supplier
With the measurements, storage list, finish direction, appliance schedule and delivery details in hand, a supplier can return a proposal built around your specification rather than an approximation of one. The cooperation steps run from the project brief and design proposal to quotation and detail confirmation, then production, shipment and follow-up — so the figure you approve is the figure tied to a defined drawing, material list and configuration.
If you are preparing an enquiry for wall-mounted bar units on a current project, send the measured drawings, the appliance list and the finish references together, and the response can set out what can be built, what still needs confirming, and what each option does to the price.