A floor-to-ceiling wall system is one of the few interior elements that cannot be ordered from a catalogue page. The opening width, the ceiling height, what sits inside the carcass and how the services are routed all change the build. That is why an enquiry for Santerson Floor to Ceiling Systems moves fastest when it arrives with the same information a workshop needs to cut panels: room dimensions, a layout intent, a finish direction and an installation plan. The list below is the practical brief we work from on residential and villa projects.
1. The wall, measured properly
Send the overall width and height of the wall in millimetres, plus the floor-to-soffit height if the ceiling is not flat. Then note everything that interrupts a clean rectangle: skirting boards, architraves, radiators, switch plates, downlights, air-conditioning grilles, uneven plaster or a column part-way along the run. A single 60 mm column in the middle of a wall changes the module split, and knowing about it before pricing avoids a second quotation.
Photographs help more than a sketch. Two straight-on shots of the full wall, plus one close-up of each obstruction, let us read the existing conditions. A simple dimensioned sketch on top of a phone photo is usually enough to start.
2. What the system has to hold
Tell us what goes in and on it, because that decides the internal make-up rather than the appearance:
- Books and heavy items — shelf spans and panel thickness are set by the load, so a library wall is built differently from a display wall.
- Television and media equipment — screen size, whether the unit is recessed or flush, and where cables and sockets need to land.
- Open display versus closed storage — most projects mix both, and the ratio drives cost more than the finish does.
- Decorative objects and lighting — niches and shelf lighting are planned at the design stage, not added afterwards.
If you are weighing open shelving against doors and drawers, our Santerson Floor to Ceiling Bookshelves page shows the configurable layout options we work with on residential projects.
3. Finish, material and hardware direction
Send the finish you want in one of three ways: a named reference from our range, a photograph of a project you like, or a physical sample or RAL/Pantone direction. Also state what it has to sit alongside — flooring, doors, kitchen cabinetry — so the tones are matched rather than merely similar. Veneer, lacquer, laminate and wood-effect panels all read differently next to the same floor, and we would rather resolve that on a drawing than on site.
Hardware choices belong in this conversation too: handleless or handled fronts, soft-close drawers, integrated door-and-paneling details, and glass-front sections. Where a wall has to disappear into the room, an integrated door and paneling approach keeps the joinery lines continuous.
4. Services, lighting and electrical points
Confirm where power, data and aerial connections are today and where you want them after installation. Shelf and niche lighting needs a driver location, a switching arrangement and a cable route decided before the panels are made — this is exactly what Santerson Integrated Lighting Systems configuration covers, and it is far cheaper to plan than to retrofit.
5. Project context: quantities, programme, delivery
A quotation also needs the commercial frame:
- How many walls or rooms are involved, and whether other joinery — wardrobes, kitchen cabinetry, media walls — is being ordered at the same time.
- The required site date and any trades that depend on the joinery arriving.
- The delivery address, access conditions and the Incoterms you want to work to, so freight and packaging are quoted realistically.
- Whether installation is by your own team or by ours, and who handles snagging and handover.
As a one-stop furniture and building materials supplier, we normally quote floor-to-ceiling systems together with the flooring, wall panelling and lighting they meet, which keeps the junction details with one manufacturer instead of three.
6. How the quotation is confirmed
With those inputs in hand, the process follows the steps we set out under our interior design services: a brief and design proposal, then drawings with dimensions, layout and finishes confirmed against your approval, then production, shipment and follow-up. Under our custom and OEM service we can also match bespoke materials, textures and branding where a project calls for it.
Dimensions, materials, hardware and electrical details are confirmed in writing for each project before manufacturing starts, so the price you approve is the specification you receive.
Ready to send your brief
Measure the wall, photograph the obstructions, decide what the system must store and how much of it should be hidden, choose a finish reference, mark up the electrical points and give us the site date. Send that to our team and we can come back with a specification and price rather than a series of questions.