A vanity mirror can look flattering in a showroom and unkind once it is installed above a bathroom basin. Shadows fall across the face, the colour of skin and stone does not match the sample board, and the fitting arrives with an electrical specification nobody checked. For buyers ordering bathroom fit-out packages for villas, serviced apartments or hotel guest rooms, vanity lighting is a small line item that decides how the whole washroom reads. The comparison below covers what to check before you place an order, and what to ask a supplier to confirm in writing.

Start with the mounting arrangement, not the fixture style

Ask first where the light will physically sit relative to the mirror and basin. Three arrangements behave very differently on site:

  • Above-mirror fitting. The simplest option, and the one most often specified by default. Light comes from a single high point, so it throws shadows downward into the eye sockets unless the fitting projects far enough beyond the mirror edge to clear the face.
  • Sconces at either side of the mirror. Two fixtures mounted at roughly face height light the front of the face evenly and are the arrangement most interior teams specify for guest rooms and powder rooms. Bathroom wall sconces in this position need a finish that matches the mirror frame, taps and other ironmongery in the room.
  • An illuminated mirror or mirror cabinet. The light source is built into the unit, so there is one product to order, wire and hand over rather than two. An LED mirror cabinet also adds enclosed storage behind the mirror, which matters in compact guest bathrooms.

Whichever arrangement you choose, record it on the drawing before pricing. A change from an above-mirror fitting to side sconces moves the electrical first-fix, and that is a wall-openings problem, not a lighting problem.

Compare what the supplier can actually vary

Catalogue vanity lights are usually offered in two or three fixed widths. On a project, the mirror width, the basin centring and the tile setting rarely allow a stock size to sit symmetrically. This is where made-to-measure work changes the outcome. When you request quotations, ask each supplier to state plainly which of the following they can change for your order:

  • Overall length and the position of the mounting centres
  • Frame finish — metal tone, glass tint, lacquer or wood veneer — so it matches other ironmongery in the same bathroom group
  • Layout of the light source, for example a single bar above the mirror or a pair of sconces with matching back plates
  • Whether the fitting can be built as part of a vanity unit, so the mirror, basin, countertop and lighting arrive as one coordinated set

SANTERSON's vanity lighting is listed within the Lighting & Accessories collection for residential bathroom projects, with made-to-measure sizing, material and finish options and a layout tailored to each project. The same configurability runs through the surrounding bathroom range: a single vanity or a double vanity can be specified to the same dimensions and finish, which is how you keep one bathroom consistent across several trades.

Put the electrical and suitability questions in writing

This is the comparison most buyers skip, and it causes the most rework. Vanity fixtures sit in a damp environment close to water, and they connect to a circuit that your local electrician must sign off. Do not assume a fixture shown online suits your zone or your supply. Ask each supplier to confirm, per project:

  • The ingress protection rating of the specific fitting in the position you have drawn
  • Wattage, colour temperature and light output for the fixture as built for your order — not the generic catalogue figure
  • Whether the driver or transformer is included, and where it will sit if it is separate
  • The supply voltage and plug or hard-wired connection required in the destination country
  • Which local standards apply to the installation, and what documentation the supplier can provide for your electrician and building certifier
Treat any electrical figure as unconfirmed until it appears on a written specification for your configuration. A product page that shows one finish photograph is not a technical submittal, and bathroom zoning rules differ by country and by state.

Judge decorative fixtures on the whole wall, not alone

Some buyers specify a purely functional strip above the mirror and stop there. In a guest bathroom or a villa principal bathroom, a decorative fitting often does more work: it sets the tone of the wall and is photographed more than anything else in the room. A sculptural illuminated piece can be both the task light beside the basin and the feature of the wall — for example the splash mirror wall lamp, a decorative LED sconce with a central mirror inside a splash-shaped transparent frame, listed for bathrooms and vanity areas. Where you go this route, confirm that the fitting still lights the face adequately at the basin, and do not rely on it as the only light source in the room.

Compare how the lighting travels with the rest of the fit-out

A vanity light ordered alone from a lighting catalogue has to be coordinated by you: finish matched to taps, size matched to a mirror made elsewhere, delivery date matched to cabinetry. Ordering the lighting inside one bathroom package removes that coordination work and reduces the number of shipments arriving on site out of sequence. Buyers sourcing several bathrooms at once usually compare suppliers on these points:

Comparison point Lighting-only supplier One bathroom package from one manufacturer
Finish consistency across mirror frame, vanity and lighting Matched by you, sample by sample Specified together in one production run
Sizes that fit the drawn mirror and basin centring Stock sizes; alterations often refused Made-to-measure sizing on request
Number of shipments and delivery dates to reconcile One per product family Consolidated for the bathroom group
Responsibility when a fitting does not match the unit Split between two vendors Single point of contact

SANTERSON is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with custom and OEM service, logistics and door-to-door delivery, and installation and after-sales support described across its service pages. That means vanity lighting can be ordered alongside vanities, basins, showers, cabinetry, wall panelling, flooring and other bathroom finishes under one project scope rather than as separate purchase orders.

A short pre-order checklist

  • Confirm the mounting arrangement on the drawing and mark the first-fix positions before any wall is closed up.
  • Request a written specification for the exact configuration you are buying, including electrical details and ingress protection.
  • Order one sample fixture and install it at site light levels before releasing the full quantity for every bathroom.
  • Ask for finish samples of frame and glass alongside the vanity and tapware samples, viewed in the actual bathroom.
  • Check that quantities are right for each bathroom type — guest, ensuite, main — and that spares are included for handover.

Talk to us about your bathroom package

Send us your bathroom layout, mirror sizes and finish direction, and we will quote vanity lighting together with the vanities, basins and other fixtures for the same project scope. Contact SANTERSON — https://www.santerson.com/contact/.