A light grey shaker kitchen rarely stalls on the drawing. It stalls in the sign-off queue. One raised panel profile, one hardware finish and one paint sample travel through a designer, a builder, a purchaser and an owner before production starts, and each of them asks a slightly different question. If cabinetry is scheduled as a single line item, those questions surface late, after carcasses are cut.

This guide sets out how to structure approvals for light grey shaker style kitchen cabinets on villa, apartment and boutique hotel work: who signs what, in which order, and which decisions have to be closed before manufacturing begins.

Why Shaker Cabinetry Draws More Sign-Offs Than It Looks Like It Needs

Shaker doors are deceptively specific. The style is defined by a flat centre panel framed by a raised border, and almost every element of that frame is a decision somebody has to approve: the width of the stile and rail, the depth of the profile, whether the corner joints are square or cope-and-stick, and how the paint is built up over the edges. Two kitchens can both be called "light grey shaker" and look completely different once those variables are set.

Then there is the colour itself. Light grey sits close enough to off-white, greige and pale blue-grey that a rendering cannot settle it. The same door in a light grey and off-white two-tone scheme reads warm under 2700K lighting and cool under 4000K, which is exactly why owners change their minds after the first delivery rather than before it.

Our light grey shaker kitchen cabinet project also carries integrated appliances — a wine refrigerator, built-in oven and microwave — plus glass display cabinets and open niches with warm LED lighting. Each of those adds another party to the approval chain: an appliance supplier for cut-out dimensions, an electrician or lighting designer for the LED feed, and whoever owns the joinery budget for the glazed units.

Map the Approvers Before You Draw Anything

On a residential renovation the owner is usually the only approver. On a villa development, a hotel fit-out or an apartment package, that role splits across several people with different authority and different concerns. Write the list down at the outset and name one decision-maker per question.

PartyWhat they are actually signing offWhere they typically block the job
Interior designer / architectDoor profile, panel proportion, colour family, hardware style, glass typeLate substitution of a door style after the elevation package is priced
Builder or site contractorSetting-out dimensions, floor and ceiling levels, services positions, delivery accessTolerances not surveyed before carcasses are made to measure
Client representative / procurementBudget allocation, unit counts, phasing across units or floorsValue-engineering finishes after tooling and samples are already paid for
End owner or operatorFinal colour and hardware sample, layout usability, display lightingColour approval deferred until a site visit, which sits on the critical path
Appliance and lighting suppliersCut-out sizes, ventilation gaps, door opening direction, transformer positionsModel selection arriving after cabinet widths are fixed

The most common failure is not disagreement — it is silence. An approver who never receives a specific question simply does not respond until the package arrives on site. Every approval round below should close with a named person, a dated deadline and an explicit statement of what happens if no response is received.

Run Approvals in Five Rounds

Splitting sign-off into five short rounds keeps each party focused on one decision set at a time, and prevents the situation where an owner approves a colour they have only ever seen as a rendering.

Round 1 — Scope and layout

Confirm the room geometry, the run lengths, the appliance list and the storage brief. This is where open niches, glass display cabinets and tall pantry units are either accepted or cut. Deciding later means re-cutting carcass widths.

Round 2 — Door style and profile

Fix the shaker door as a physical detail: stile and rail width, panel relief, edge break, and whether upper cabinets continue the same profile or switch to a glass-fronted variant. Our Shaker Kitchen Cabinets range covers solid-panel, two tone shaker cabinets, grey shaker cabinets and glazed configurations, so mixed doors within one kitchen are workable — but the mix has to be drawn before the elevation package is issued for pricing.

Round 3 — Colour and finish samples

Issue painted samples on an actual door section, not a flat chip board, because the panel relief and shadow lines change how a light grey reads. Ask the owner to view them against their own worktop, splashback and flooring samples, under both daylight and the room's intended lighting temperature. Approve in writing, with the sample reference recorded.

Round 4 — Hardware, glass and integrated lighting

Golden handles and knobs on light grey create the soft contrast that defines this scheme, so hardware is a design decision rather than a commodity purchase. Confirm handle length and fixing centres, hinge type for the door weight, glass specification for display cabinets, and where LED drivers sit — access matters more than most people expect.

Round 5 — Production drawings and make-to-measure dimensions

The final round is dimensional. Site-verified measurements, floor levels, service positions and appliance cut-outs are confirmed against the shop drawings, and the builder signs them. Nothing goes into production until this signature exists.

What Must Be Frozen Before Manufacturing Starts

Treat the list below as a hard gate. Anything still open when it closes becomes a change order, and cabinetry change orders are expensive because they arrive after panels are cut and sprayed.

  • Door profile drawing, including stile and rail widths and panel relief
  • Approved paint or lacquer sample with reference number for every colour in the scheme
  • Final appliance models with cut-out dimensions and ventilation requirements
  • Handle, knob and hinge specification with fixing centres
  • Glass type, glazing bar layout and internal shelf positions for display cabinets
  • Internal storage configuration: drawer stacks, pull-out trays, dividers, bin housings
  • Site-verified dimensions signed by the builder, including floor and ceiling levels
  • Lighting specification and driver positions for niches and glazed units

Where a project repeats the same kitchen across several apartments or guest rooms, approve one full reference kitchen completely before releasing the rest. A single approved prototype absorbs the ambiguity; approving each unit separately multiplies it.

Keep One Written Record Across Every Round

Approvals fail when decisions live in three email threads and a WhatsApp group. Use one running document per project that records, for each round: the question asked, who was asked, the response date, the approved reference (sample code, drawing revision, hardware SKU) and anything explicitly deferred.

That record also protects quality. When an owner queries a shade difference two years after handover, the sample reference in the approval log answers it immediately. When a purchasing change is proposed mid-programme, the log shows exactly which approved item is being replaced and who has to re-sign.

A practical rule: if a decision can be reversed without re-manufacturing, let it stay open. If it cannot — colour, profile, dimensions, appliance cut-outs — close it in writing before the order is released, and let nothing move past that point informally.

How a Single Supplier Simplifies the Chain

Approvals get harder when cabinetry, joinery, worktops and matching wardrobes come from different vendors, because each party waits for the others' drawings before committing. Sourcing built-in furniture through one manufacturer keeps elevations, carcass details and hardware schedules in a single revision sequence.

As a one-stop furniture and building materials supplier, SANTERSON handles custom cabinetry from dimension survey through production and delivery, with made-to-measure sizing, panel material and surface finish selected per project. Our custom built-in kitchen cabinets are supplied as interior fixtures for hotel, apartment and residential renovation work, with matching hinges, drawer slides, support legs and connecting brackets specified alongside the carcasses. For villa and boutique hotel kitchens that combine shaker doors with integrated appliances and lit display cabinets, that single coordination point is what keeps five approval rounds to five rather than fifteen.

Planning a kitchen package for a villa, apartment or hospitality project? Send us your elevations, appliance schedule and target finish, and we will return shop drawings, a sample set and a production timeline built around your approval dates — contact SANTERSON to start the first round.